Chapin 4163 Manual

Chapin Ikke kategoriseret 4163

Læs gratis den danske manual til Chapin 4163 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Chapin 4163, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Pump gasket

Empaquetadura para

labomba

Joint d’étanchéité de

pompet

O-ring

Anillo en “o”

Anneau torique

Plunger cup

Cupde émbolo

Plongeur piston

1. Pre-Use Check

2. Filling

1) Turn pump handle counterclockwise and remove pumpDo:

2) Do: Prepare spray solution following all directions and safety warnings on chemical label.

3) Fill tank to no more than the proper gallon marker. Do NOT: overﬁll to accommodate pump. Do:

4) Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank Do:

and tighten securely.

O-ring

Anillo en “o”

Anneau torique

Spring

Resorte del

émbolo

Ressortde tige

Pump gasket

Empaquetadura para labomba

Joint d’étanchéité de pompe

Spring

Resorte del

émbolo

Ressortde tige

Nut (2)

Tuerca

Ecrou

Check valve

Válvula de

retención

Clapet anti-retour

Fibre gasket (2)

Boquilla abancio

Joint de ﬁbre

O-ring (2)

Anillo en “o”

Anneau torique

Cup disc

Disco esparicidor

Disque

d’ecartment

Washer

Arandela de

soporte

Rondelle

1) Check tightness of hose nut to be sure hose is securely attached to the tank outlet. Do:

2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found,

replace hose before using. Replace with original manufacturer’s parts only.

3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior

of tank for signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank

weakening and could result in explosive bursting under pressure. If any of these signs are found,

discard tank immediately and replace. Do not attempt to patch leaks, etc., as this could result in

serious injury.

4) Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 Do:

strokes and inspect for leaks).

5) Direct shut-off away from you and open to make sure discharge is not clogged. Do:

6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and

proceed with Filling, Pressurizing and Spraying Instructions.

7) Inspect all metal parts including the wand, nozzle and ﬁttings for rust, corrosion and pitting. Do:

If any of these conditions are found, replace affected part with original manufacturer’s part

before using.

Lock

Position

TO LOCK HANDLE: Push handle down

to depress coil spring and turn handle

1/4 turn clockwise, then allow handle to

raise into lock position.

3A 3B

TO LOCK PUMP: Place pump prongs down into slots in funnel, turn

clamp clockwise to furthest position under bottom slot, then turn

handle clockwise until tightly locked and sealed in place.

3C3C

TO RELEASE HANDLE: Push down to depress coil spring and turn

handle counterclockwise 1/4 turn, then lift handle.

Pump until you feel resistance.

TO UNLOCK PUMP: Turn handle counterclockwise until 3-prong clamp is

loose. Then rotate clamp counterclockwise to stop and lift out.

3D3D

3. Pressurizing and Spraying

3E3E

3F3F

3. Pressurizing and Spraying, continued

018262R0122

Parts, Piezas, Pièces

Sk-1154-1

WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious

eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a

pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.

Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants

and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.

Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump

assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than

the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer’s original

parts. Never spray ﬂammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,

pressure, or gas producing chemicals. Always read and follow chemical manufacturer’s instructions

before use with this sprayer as some chemicals may be hazardous when used with this sprayer.

WARNING

Congratulations!

You have just purchased a quality Chapin product.

Call us @ 1-800-950-4458 or www.chapinmfg.com

Note: Your particular sprayer may not include all parts pictured above.

Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.

Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.

6-4627

Repair Parts Kit Gaskets and Seals (not included)

Juego de piezas de reparación, empaquetaduras y juntas (no incluido)

Kit de pièces de réparation, joints et garniture d’étanchéité (non inclus)

P.O. Box 549 700 Ellicott St.

Batavia, NY 14021-0549 U.S.A.

1-800-950-4458 www.chapinmfg.com

FOR HELP USING TRI-LOCK PUMP SEE VIDEO

https://chapinmfg.com/pages/industrial-videos

4. To Release Pressure

1) With pump facing away, turn locked handle counterclockwise until air begins to escape. Do:

Stop turning handle when you hear air escaping.

2) Do: Stay away from the sprayer until all air has escaped.

5. Care, Storage and Maintenance

1) Do: Follow chemical manufacture’s instructions for cleaning. Rinse thoroughly with

recommended solvent. Follow Filling, Pressurizing and Spraying Instructions, except pump unit

only 8-10 strokes. Be sure that the wand and nozzle are thoroughly rinsed after each use.

2) Do: Open shut-off and allow recommended solvent to run through discharge assembly.

3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.

4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.

5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening

in cover.

Produkt Specifikationer

Mærke:	Chapin
Kategori:	Ikke kategoriseret
Model:	4163

Har du brug for hjælp?

Hvis du har brug for hjælp til Chapin 4163 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Chapin Manualer

17 September 2025

27 August 2025

27 August 2025

26 August 2025

26 August 2025

22 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

20 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Witt Smart Touch Air Pump Manual

3 November 2025

ANCEL HD3400 Manual

3 November 2025

Fromm & Starck STAR_MCAB_16 Manual

3 November 2025

Slingshot R (2022) Manual

3 November 2025

Beverage-Air WTFCS52HC-60 Manual

3 November 2025

ANCEL V6 PRO Manual

3 November 2025

Leviton 5304M-2N7 Manual

3 November 2025

ANCEL BST500 Manual

3 November 2025

Beverage-Air Horizon HRP1HC-1S Manual

3 November 2025

FreeMotion P50 Manual

3 November 2025