Columbus P-1 Mark II Manual

Columbus Ikke kategoriseret P-1 Mark II

Læs gratis den danske manual til Columbus P-1 Mark II (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Columbus P-1 Mark II, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
• Power on: Green, always on
• Sleeping: Green, flashing
• Low battery: Red, flashing
• Charging: Red, always on
• Fully charged: Green, always on
• Spy mode: Blue
Parts Description
Main Status Lamp
MicroUSB connector
MicroSD slot
Reset
Log Lamp
GNSS Status Lamp Motion Detection Lamp
1
• Acquiring satellite: Always on
• GNSS is fixed: Green, flashing
• GNSS is fixed (Best Positioning):
Blue, flashing
• Motion Detection Mode On/Off:
Always On/Off
• Device is in motion: Flashing
Logging a track
Long press the "Power button" to
power on.
Long press the "Power button" to
turn the device off and save the
track.
Do not remove the memory
card while it is turned on,
which will result in data loss!
5
Power button Point of interest button
2
On
Reset
Function button
If the memory card fails to log, the Log lamp will flash continuously
with continuous warning sound. In such case, please format or replace
the card.
• Long press: Turn On/Off .
• Short press: Turn On/Off Motion
Detecting Mode.
• Short press: Mark the current
position as a point of interest (POI).
(for CSV files only)
• Long press: Start a new track.
• If the device stops responding, use a
pin to press the reset hole to reset.
• Short press: Pause / continue
logging (default).
• This button can be configured to
other functions, see page 6.
Short press the "Power button" to
turn On/Off the Motion Detection
Mode.
Wait for GNSS positioning in the
open air. The cold start needs 1-3
minutes. When the "GNSS status
lamp" and the "Log lamp" start
flashing, it indicates track logging
has started.
Off
The notch
is on the left.
P-1 M2 supports high capacity SDXC MicroSD card, we recommend the 4G-32G.
Insert the MicroSD card into the slot. Please note the direction of the card. The
notch of the card should be leftward.
CAUTION
GB
This manual is intended to guide you through the safe and
correct use of the product and its accessories, avoiding improper
operations that may result in injury of yourself or any other
person or cause device damage.
The protection class is IP66, P-1 M2 can work normally in rain,
snow and high dust environments. The rubber connector cover
must be fully covered.
Do not immerse P-1 M2 in water. Do not try to damage or
puncture the device, otherwise, electrolyte in its built-in battery
may leak or combust, causing injury or environmental pollution.
As a precision electronics, the product contains no component
that can be repaired by your own. Any attempt to disassemble
the product will void the original manufacturer's warranty.
Thank you for choosing our product.
Point of interest button
Log lamp
Main status lamp
GNSS status lamp
Motion detection lamp
Function button
Power button
Hand strap hole
Rubber connector cover
Quick
Quick
Quick
Quick Quick Star
Star
Star
StarStart
t
t
tt
Quick
Quick
Quick
Quick Quick Star
Star
Star
StarStart
t
t
tt
Pr
Pr
Pr
PrPro
o
o
oofe
fe
fe
fefes
s
s
sss
s
s
ssi
i
i
iion
on
on
onona
a
a
aal G
l G
l G
l Gl GNS
NS
NS
NSNSS D
S D
S D
S DS Da
a
a
aat
t
t
tta Lo
a Lo
a Lo
a Loa Log
g
g
ggge
ge
ge
geger
r
r
rr
Pr
Pr
Pr
PrPro
o
o
oofe
fe
fe
fefes
s
s
sss
s
s
ssi
i
i
iion
on
on
onona
a
a
aal G
l G
l G
l Gl GNS
NS
NS
NSNSS D
S D
S D
S DS Da
a
a
aat
t
t
tta Lo
a Lo
a Lo
a Loa Log
g
g
ggge
ge
ge
geger
r
r
rr
• High speed log: Flash every 1 second
(10Hz/5Hz)
• Normal log: Flash every 3 seconds
(1Hz/distance interval)
• MicroSD card error or no card:
Continuous flashing
• Pause: Always on
3
P-1 M2 has three operating modes: Normal Mode, Motion
Detection Mode and Spy Tracking Mode.
Motion Detection Mode
How to enter this mode: Power on, short press the "Power
Button", the motion detection lamp (white) lights up.
When P-1 M2 is stationary, the lamp is on. When P-1M2 is in
motion, the lamp is flashing. When P-1 M2 stops moving or
loses the satellite signal more than 5 minutes, it enters the
standby mode automatically. Once P-1 M2 detects motion, it
automatically wakes up and continues to log. This mode is
suitable for long time records of vehicles and other large
objects.
Spy Tracking Mode
How to enter this mode: In the power-off state, press the
"Power button" and the "Function button" simultaneously for
about 3 seconds.
In this mode, P-1 M2 gets positioned and logs 8 way points at a
certain time interval*. When P-1 M2 is standby, the main status
lamp intermittently flashes in blue. All other lamps on the
device are off and the speaker is mute. This mode is suitable for
tracking your car for an extended period, or for places where
charging is unavailable, e.g. in a long hiking.
* See page 5 for the value of the interval can be customized. See page 9 for the battery
life under different intervals. Spy tracking mode is only recorded at 1Hz, CSV format.
+
Log Mode
Power-off
Long press Long press
Motion Detection
Mode SPY Tracking
Mode
Normal Mode
Short press
For the first use, visit the link to obtain the default
configuration file which is named as CONFIG.TXT:
Obtain the configuration file
http://cbgps.com/p1m2/q
Details about configuration
[SETTINGS]
TimeZone
SpeedAlert
AutoPowerOn
Beeper
-12:00, -11:00, -10:00, -09:30, -09:00, -08:00, -07:00,-06:00,
-05:00, -04:30, -04:00, -03:30, -03:00, -02:30, -02:00, -01:00,
, +01:00, +02:00, +03:00, +03:30, +04:00, +04:30,+00:00
+05:00, +05:30, +05:45, +06:00, +06:30, +07:00, +08:00,
+08:45, +09:00, +09:30, +10:00, +10:30, +11:00, +11:30,
+12:00, +12:45, +13:00, +13:45, +14:00
OFF or value 1 200 : -
OFF, ON
OFF, ON
Values for conguration (the blue value is default)
Time zone. The default is UTC time (+00:00), please check your local time
zone in advance (for CSV les only).
Speed alarm. When the speed exceeds the value, the P-1 M2 will alert.
Short press the "POI Button" to temporarily stop.
Auto power on. When connecting to the MicroUSB cable, P-1 M2
automatically turns On/Off with the power status.
Beeper. Turn On/Off the beeper.
+
x3 x3
Configuring the Device
Press simultaneously Long beep
e.g.: The track recorded in January, 2022 is saved in the "2022-
01" folder. "0208050.CSV" means the CSV track is recorded at
08:20:50 on 2nd January.
Track file naming
View the current configuration
Make sure there is no CONFIG.TXT under the root directory of the MicroSD card.
In the power-off state, press the "Power button" and the "POI button"
simultaneously until you hear 3 short beeps and then one long beep, then P-1
M2 will be turned off, which indicates that the current configuration file has
been exported successfully. The current configuration file (INFO.TXT) is stored
under the root directory of the MicroSD card.
+
It takes about 10-30 seconds (4G-32G) be
recognized by computer, depending on the size
of the TF card, please wait patiently for the
connection.
The data can only be read when P-1 M2 is
turned off.
INFO
TXT
Long press Long beep
x3
If the AutoPowerON is configured as ON, press and hold the POI button
to connect the data cable.
USB disk mode
The USB port of P-1 M2 supports two operating modes
Read files from the MicroSD card in P-1 M2.
GNSS receiver mode
P-1 M2 can be used as an external GNSS receiver, and users can
view the real-time location data.
Power on P-1 M2 first, then connect it to the computer via a USB cable.
For more information please visit
http://cbgps.com/p1m2/q
Turn off P-1 M2. Connect P-1 M2 to the computer, copy the configuration file
under the root directory of the MicroSD card, and eject the device.
In the power-off state, press the "Power Button" and the "POI Button"
simultaneously until you hear 3 short beeps, then the 3 lamps will flash three
times at the same time, and finally you hear one long beep, indicating the
configuration is successfully completed.
Configuration steps
4
4
4
4445
5
5
55
Connect to End Devices

Produkt Specifikationer

Mærke: Columbus
Kategori: Ikke kategoriseret
Model: P-1 Mark II

Har du brug for hjælp?

Hvis du har brug for hjælp til Columbus P-1 Mark II stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Columbus Manualer

Columbus

Columbus P-1 Mark II Manual

22 August 2024
Columbus

Columbus P-7 Pro Manual

22 August 2024
Columbus

Columbus P-10 Pro Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Miele

Miele WTV 417 Manual

10 Oktober 2025
Miele

Miele EBA 7747 Manual

10 Oktober 2025
Panasonic

Panasonic MX-HG4401 Manual

10 Oktober 2025
Fresh 'n Rebel

Fresh 'n Rebel Selfie Stick Manual

10 Oktober 2025
TOA

TOA VX-3308WM Manual

10 Oktober 2025
Teka

Teka EWH 100 DHH Manual

10 Oktober 2025
Xerox

Xerox App Gallery Manual

10 Oktober 2025
Miele

Miele WTV 511 Manual

10 Oktober 2025
Miele

Miele WTV 601 Manual

10 Oktober 2025
Miele

Miele GaLa-S Manual

10 Oktober 2025