Columbus P-10 Pro Manual

Columbus Ikke kategoriseret P-10 Pro

Læs gratis den danske manual til Columbus P-10 Pro (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Columbus P-10 Pro, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

•Power on: Green, always on

•Sleeping: Green, flashing

•Low battery: Red, flashing

•Charging: Red, always on

•Fully charged: Green, always on

•Spy mode: Blue

Parts Description

Main Status Lamp

MicroUSB connectorMicroSD slot

Reset

Log Lamp

GNSS Status Lamp Motion Detection Lamp

•Track logging: Flash every 3 seconds

•Pause: Always on

•MicroSD card error or no card:

Continuous flashing

•Acquiring satellite: Always on

•GNSS is fixed: Green, flashing

•GNSS is fixed (Best Positioning):

Blue, flashing

•Motion Detection Mode On/Off:

Always On/Off

•Device is in motion: Flashing

Logging a track

Long press the "Power button" to

power on.

Long press the "Power button" to

turn the device off and save the

track.

Do not remove the memory

card while it is turned on,

which will result in data loss!

Power button Point of interest button

Reset

Function button

If the memory card fails to log, the Log lamp will flash continuously

with continuous warning sound. In such case, please format or replace

the card.

•Long press:Turn On/Off .

•Short press: Turn On/Off Motion

Detecting Mode.

•Short press: Mark the current

position as a point of interest (POI).

(for CSV files only)

•Long press: Start a new track.

•If the device stops responding, use a

pin to press the reset hole to reset.

•Short press: Pause / continue

logging (default).

•This button can be configured to

other functions, see page 5.

Short press the "Power button" to

turn On/Off the Motion Detection

Mode.

Wait for GNSS positioning in the

open air. The cold start needs 1-3

minutes.When the "GNSS status

lamp" and the "Log lamp" start

flashing, it indicates track logging

has started.

Off

The notch

is on the left.

P-10 Pro supports high capacity SDXC MicroSD card, we recommend the 4G-32G.

Insert the MicroSD card into the slot. Please note the direction of the card.The

notch of the card should be leftward.

CAUTION

Thank you for choosing our product.

This manual is intended to guide you through the safe and

correct use of the product and its accessories, avoiding improper

operations that may result in injury of yourself or any other

person or cause device damage.

As a precision electronics, the product contains no component

that can be repaired by your own. Any attempt to disassemble

the product will void the original manufacturer's warranty.

The protection class is IP66, P-10 Pro can work normally in rain,

snow and high dust environments. The rubber connector cover

must be fully covered.

Do not immerse P-10 Pro in water. Do not try to damage or

puncture the device, otherwise, electrolyte in its built-in battery

may leak or combust, causing injury or environmental pollution.

Quick

QuickQuick Star

Star

StarStart

Quick

QuickQuick Star

Star

StarStart

Prof

ProfProfessional

essional

essionalessional HD GNSS

HD GNSS

HD GNSS HD GNSS Data L

Data L

Data L Data Logger

ogger

oggerogger

Quick

QuickQuick Star

Star

StarStart

Prof

ProfProfessional

essional

essionalessional HD GNSS

HD GNSS

HD GNSS HD GNSS Data L

Data L

Data L Data Logger

ogger

oggerogger

Point of interest button

Log lamp

Main status lamp

GNSS status lamp

Motion detection lamp

Function button

Power button

Hand strap hole

Rubber connector cover

P-10 Pro has three operating modes: Normal Mode, Motion

Detection Mode and Spy Tracking Mode.

Motion Detection Mode

How to enter this mode: Power on, short press the "Power

Button", the motion detection lamp (white) lights up.

When P-10 Pro is stationary, the lamp is on. When P-10 Pro is in

motion, the lamp is flashing. When P-10 Pro stops moving or

loses the satellite signal more than 5 minutes, it enters the

standby mode automatically. Once P-10 Pro detects motion, it

automatically wakes up and continues to log. This mode is

suitable for long time records of vehicles and other large

objects.

Spy Tracking Mode

How to enter this mode: In the power-off state, press the

"Power button" and the "Function button" simultaneously for

about 3 seconds.

In this mode, P-10 Pro gets positioned and logs 8 way points at

a certain time interval*. When P-10 Pro is standby, the main

status lamp intermittently flashes in blue. All other lamps on

the device are off and the speaker is mute. This mode is suitable

for tracking your car for an extended period, or for places where

charging is unavailable, e.g. in a long hiking.

* See page5 for thevalue ofthe interval canbe customized. See page 9for the battery

life under different intervals. Spy tracking mode is only recorded at 1Hz, CSV format.

Log Mode

Power-oﬀ

Long press Long press

Motion Detection

Mode SPY Tracking

Mode

Normal Mode

Short press

Obtain the configuration file

For the first use, visit the link to obtain the default

configuration file which is named as CONFIG.TXT:

http: cbgps com/p10/config en.htm// .

Details about configuration

[SETTINGS]

TimeZone

SpeedAlert

AutoPowerOn

Beeper

-12:00,-11:00, -10:00,-09:30, -09:00, -08:00,-07:00,-06:00,

-05:00, -04:30, -04:00, -03:30, -03:00, -02:30, -02:00,-01:00,

, +01:00, +02:00, +03:00,+03:30, +04:00, +04:30,+00:00

+05:00, +05:30, +05:45, +06:00,+06:30, +07:00, +08:00,

+08:45, +09:00, +09:30, +10:00,+10:30, +11:00, +11:30,

+12:00, +12:45, +13:00, +13:45,+14:00

OFF or value 1 200: -

OFF, ON

Values for conguration (the blue value is default)

Time zone. The default is UTC time (+00:00), please check your local time

zone in advance (for CSV les only).

Speed alarm.When the speed exceeds the value, the P-10Pro willalert.

Short press the "POI Button" to temporarily stop.

Auto power on. When connecting to the MicroUSB cable, P-10 Pro

automatically turns On/Oﬀ with the power status.

Beeper. Turn On/Oﬀ the beeper.

Configuration steps

Turn off P-10 Pro. Connect P-10 Pro to the computer, copy the configuration file

under the root directory of the MicroSD card, and eject the device.

In the power-off state, press the "Power Button" and the "POI Button"

simultaneously until you hear 3 short beeps, then the 3 lamps will flash three

times at the same time, and finally you hear one long beep, indicating the

configuration is successfully completed.

+x3 x3

Configuring the Device

Press simultaneously Long beep

444

FunctionButton Pause, POI

Function Button. It can be congured for two purposes: POI or Pause.

Pause: Press this button to pause logging, press again to continue.

POI: Press this button to m arkthe current position as the second type of

POI (for CSV les only).

[RECORD]

Format

LogMode

SpeedMask

SpyModeTimer

OneTrackPerDay

1Hz,

5m, 10m, 20m, 50m, 100m

20ft, 50ft, 100ft, 200ft, 500ft

OFF or value 200: -1

1 - 60, default: 5

Values for conguration (the blue value is default)

Track format. P-10 Pro oﬀers three original le formats: CSV (plain code

format), GPX (common exchange format), NMEA (NMEA 0183 format).

Log mode. By frequency, e.g.: 1Hz (1 trackpoint per second);By distance,

e.g.: 5m, 10m(Metric) / 20ft, 50ft(Imperial), (for CSV, GPX les only).

Speed mask: Only record the track points whose speed exceeding the

value .(for CSV, GPX les only)

Interval of SpyTracking Mode: Set up the wake up interval (minute).

OFF, ON

One track per day. OFF: A new le is generated each time it is turned on.

ON: Only one le is generated per day, and all the tracks are automatically

merged into one track.

CSV, GPX, NMEA

[UNIT]

Speed

Values for conguration (the blue value is default)

km/h, mi/h

Tips about configuration error

Users can customize the configuration, only limited to the contents and formats

listed in the above table (case sensitive).

Attention! The configuration cannot take effect if the configuration value does not

conform to the format and content requirements. In case of abnormality, the main

status lamp will flash in red, and the buzzer will give 5 short beeps as an error

prompt. Please check the configuration values and fix it.

x5+Red

flashing Configuration

failure

Check the

configuration

555

Speed Unit: km/h (Metric),mi/h (Imperial).

This conguration is only valid for SpeedAlert and SpeedMask.

Produkt Specifikationer

Mærke:	Columbus
Kategori:	Ikke kategoriseret
Model:	P-10 Pro

Har du brug for hjælp?

Hvis du har brug for hjælp til Columbus P-10 Pro stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Columbus Manualer

Columbus P-1 Mark II Manual

22 August 2024

Columbus P-7 Pro Manual

22 August 2024

Columbus P-10 Pro Manual

22 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

10 Oktober 2025

Oras Saga 3970 Manual

10 Oktober 2025

TOA AT-4030B-EB Manual

10 Oktober 2025

TOA VX-030DA Manual

10 Oktober 2025

TOA RS-481 Manual

10 Oktober 2025

TOA AT-4200B-EB Manual

10 Oktober 2025

Xerox DocuShare Manual

10 Oktober 2025