Cotech DT8800IP44-5M Manual

Cotech Ikke kategoriseret DT8800IP44-5M

Læs gratis den danske manual til Cotech DT8800IP44-5M (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Cotech DT8800IP44-5M, eller vil du spørge andre brugere om produktet?

Side 1/5
GREAT BRITAIN CUSTOMER SERVICE tel. 020 8247 9300 e-mail customerservice@clasohlson.co.uk internet www.clasohlson.co.uk
postal 10 13 Market Place, Kingston Upon Thames, Surrey, KT1 1JZ
1 2 3
4
5
Ver. 20170920
Flexible RGB LED Strip
Art.no 36-6703 Model DT8800IP44-5M
Please read theentire instruction manual before using theproduct
and then save it for future reference. We reserve theright for
any errors in text or images and any necessary changes made
to technicaldata. In theevent of technical problems or other
queries, please contact our Customer Services.
Safety
Theproduct should only be connected to a230 V AC,
50Hz electrical outlet.
Never immerse theproduct in water or other liquid.
Do not place theproduct where there is arisk of it falling
into water or other types of liquid.
Theproduct may only be used with thesupplied mains adaptor.
Theproduct must not be changed or modified in anyway.
Never hang anything on theproduct.
Do not look directly into thelight source as there is arisk
for eye damage.
Never attempt to interconnect theproduct with other light strips.
Make sure that thepower adaptor is not pinched or
damaged in any other way duringuse.
Never use theproduct if it, its power adaptor or plug are
damaged in anyway.
Never let children play with theproduct.
Operating instructions
3. Connect theLED strip to thepower adaptor according to
thefigure (thearrow in thepicture shows theIR receiver for
theremote control).
3. [ ON/OFF ] Power switch
4. [ R, G, B, W ] Solid colour selections
5. [ FLASH ], [ STROBE ], [ FADE ], [ SMOOTH ] Light modes with
7 colours which transition quickly, slowly, smoothly,etc.
Care and maintenance
Unplug thepower adaptor from thewall socket before
wiping it clean with adrycloth.
If thepower adaptor is not to be used for anextended
period, it should be unplugged and stored in adry location
out of reach of children.
Changing theremote control batteries
1. Follow theillustration on theback of theremote control.
2. Press in thebattery compartments latch and slide it to
release and pull thebattery holder from thecompartment.
3. Insert anew battery into thebattery holder. Makesure that
thepositive (+) terminal is facing upwards, towardsyou.
4. Reinsert thebattery holder back into theremote control.
Responsible disposal
This symbol indicates that this product should not
be disposed of with general householdwaste.
Thisapplies throughout theentire EU. Inorder to
prevent any harm to theenvironment or health
hazards caused by incorrect waste disposal,
theproduct must be handed in for recycling so
that thematerial can be disposed of in aresponsible manner.
Whenrecycling your product, take it to your local collection
facility or contact theplace of purchase. Theywill ensure that
theproduct is disposed of in anenvironmentally sound manner.
Specifications
Note: Withtheexception of theremote control, theproduct
itself has anIP44 rating.
LED strip with RGB controller, designed to be powered
from a12 V DC, max 1.8 Apower source.
Theincluded power adaptor delivers 12 V DC, max 2 A, 24 W.
Bulb: 150LEDs with a460–620 nm wavelengthrange.
Size: length 5 m, width 12.5 mm, height 4mm. Acertain
amount of deviation in size can be present due to
theglue’s elasticity and thesilicone housing.
Remote control battery 1×CR2025, 3 V.
1. Thelight strip can be
cut to adesired length.
Note:Cutonly where
marked as shown in
thefigure.
2. Use theincluded adhesive
to glue theprotective
cover over theopen
end of thelightstrip.
Lettheadhesive cure for
at least 12 hours before
subjecting it toload.
4. Hang up thestrip with theincluded cableclips. Becareful
not to damage thecable or mounting surface during
hanging.
5. Plug themains adaptor into anelectrical outlet.
Remote control
Pull theplastic film tab away from thebattery compartment in
order to activate thebattery.
1. Press repeatedly to increase
thebrightness of solid
colours. Increase thespeed
of colour transitions in
thefollowingmodes:
FLASH, STROBE, FADE and
SMOOTH.
2. Press repeatedly to decrease
thebrightness of solid
colours. Decrease thespeed
of colour transitions in
thefollowingmodes:
FLASH, STROBE, FADE and
SMOOTH.


Produkt Specifikationer

Mærke: Cotech
Kategori: Ikke kategoriseret
Model: DT8800IP44-5M

Har du brug for hjælp?

Hvis du har brug for hjælp til Cotech DT8800IP44-5M stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Cotech Manualer

Cotech

Cotech HT7715 Manual

18 September 2024
Cotech

Cotech K-CPL-LS4W-IR-S3 Manual

16 September 2024
Cotech

Cotech J1x-JF2-210/20 Manual

14 September 2024
Cotech

Cotech TD9511-3 Manual

12 September 2024
Cotech

Cotech S1J-AJ8-10 Manual

31 August 2024
Cotech

Cotech J5218D Manual

27 August 2024
Cotech

Cotech 50053 Manual

27 August 2024
Cotech

Cotech 51097X23 Manual

27 August 2024
Cotech

Cotech 36-6286 Manual

27 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer