Cotech LS9A123-1-01 Manual

Cotech Ikke kategoriseret LS9A123-1-01

Læs nedenfor 📖 manual på dansk for Cotech LS9A123-1-01 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 31 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Side 1/4
UNITED KINGDOM www.clasohlson.co.uk
Ver. 20220728
Care and maintenance
Unplug themains lead from thewall
socket before cleaning.
The product should be cleaned using
adry cloth or vacuum cleaner.
Responsible disposal
This symbol indicates that
theproduct should not be
disposed of with general
household waste. This applies
throughout theentire EU. In
order to prevent any harm
to theenvironment or health
hazards caused by incorrect waste
disposal, theproduct must be handed
in for recycling so that thematerial
can be disposed of in aresponsible
manner. When recycling your product,
take it to your local collection facility or
contact theplace of purchase. They will
ensure that theproduct is disposed of in
anenvironmentally sound manner.
Specifications
Mains adapter
Power supply 230 V AC, 50/60 Hz
Output 24 V DC, 1 A, 24 W
Strip light
36-7974
Dimensions 6000 x 10 mm
Light source 324 xLED
36-7975
Dimensions 3000x10 mm
Light source 162 xLED
Remote control
Range Max 7 m from straight
ahead, 3 m from thesides.
Battery 1 x CR2025 (included)
Risk of eye damage. Do not look directly at thelight source.
The product is not suitable for illuminating aroom.
The product is intended for indoor use only.
Class II mains adapter.
Class III strip light
Installation
Information
The LED strip light can be mounted using thedouble-sided adhesive tape (mounted).
For best adhesion, ensure that thesurface is clean, dry and free of grease.
The length of thelight strip can be adjusted by cutting it at one of thesoldering
points which are spaced every 33 cm along its length.
Note: Once thestrip light has been cut and shortened, it is no longer possible to
extend it with additional strip lights.
1. Strip light: Remove theprotective film from thetape on theback of thelight
strip and attach it to aclean, grease-free surface. The strip light may also be
screwed on with plastic clips.
2. Connectors. Connect thestrip light and thecontrol box together.
Note: Make sure thestrip light is connected in theright way, with thearrows
pointing towards each other. Otherwise thestrip light will not work.
3. IR Receiver.
Note: Make sure there are no obstacles between theIR receiver on theLED
control unit and theremote control.
4. Control unit
5. Connection cable: Connect theconnection cable to theLED control unit.
6. Mains adapter: Plug themains adapter into anelectrical outlet.
LED strip light extension set
Art. no: 36-7975 (sold separately)
1. Unplug theadapter from theelectrical outlet.
Extendable RGBW LED Strip Light
Art.no 36-7974 Model LS9A123-1-01
36-7975 LS9A123-2-01
Read theentire instruction manual before use and save it for future reference.
We apologise for any text and picture errors and any changes of technical data.
If you have any questions concerning technical problems please contact our
Customer Services.
Safety
Warning:
Neither theproduct nor its mains adapter may be dismantled or modified in
any way.
Never use theproduct or themains adapter if it is in any way damaged or
malfunctioning. Unplug theproduct immediately if it is damaged.
Do not use theproduct in environments where explosive or flammable gases
are stored or used.
The product must only be connected to theincluded mains adapter.
Never connect several or other types of devices to themains adapter.
The product must not be installed on awet or electrically conductive surface.
Make sure that thecables are not damaged whilst theproduct is being installed.
Always unplug themains adapter from thewall socket when theproduct is
not in use.
Do not carry theproduct using themains lead and do not use it for other
unsuitable purposes.
Never let children play with theproduct.
The product may be used by persons with reduced physical, sensory or
mental capabilities or persons with alack of experience or knowledge which
could jeopardise their safety, provided they have been instructed in thesafe
operation of theproduct and understand thehazards involved.
Important
The LEDs cannot be replaced. When theLEDs have reached theend of their
service life, theentire product must be discarded.
This product is intended only for private use.
5 6321 4
2. Remove theprotective film
from thetape on theback
of thestrip light and attach
thestrip to aclean, grease-
free surface. The strip light
may also be screwed on with
plastic clips.
3. Connect thestrip lights together with one another.
Note: Make sure thestrip light is connected in theright way.
Otherwise thestrip light will not work.
Remote control
1. 12 colour tones within theRGB spectrum
2. [ R ] Red light
[ G ] Green light
[ B ] Blue light
[ W ] White light
3. [ ] Increase light intensity
[ ] Decrease light intensity
4. [ OFF ] Turn thestrip light off
[ ON ] Turn thestrip light on
5. [ FLASH ] Change slowly between all thecolours
6. [ STROBE ] Change quickly between all thecolours
7. [ FADE ] Change between all thecolours, thecolours fade into one another
8. [ SMOOTH ] Change between all colours with no visible transition
5
6
7
8
1
2
34


Produkt Specifikationer

Mærke: Cotech
Kategori: Ikke kategoriseret
Model: LS9A123-1-01

Har du brug for hjælp?

Hvis du har brug for hjælp til Cotech LS9A123-1-01 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Cotech Manualer

Cotech

Cotech EMP416S Manual

25 April 2024
Cotech

Cotech LS9A123-1-01 Manual

19 Februar 2024
Cotech

Cotech CT-2410 Manual

4 Februar 2024
Cotech

Cotech HT8711 Manual

10 November 2023
Cotech

Cotech 32-2610 Manual

28 Oktober 2023
Cotech

Cotech SPH01-10E Manual

25 Oktober 2023
Cotech

Cotech PT260 Manual

16 September 2023
Cotech

Cotech EMP426SATT Manual

14 September 2023

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer