Crestron AMP-2100-70 Manual

Crestron Modtager AMP-2100-70

Læs gratis den danske manual til Crestron AMP-2100-70 (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Crestron AMP-2100-70, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

DO GUIDE

AMP-150-70/AMP-150-100/AMP-225/AMP-1200-70/AMP-1200-100/

AMP-2100/AMP-2100-70/AMP-2100-100

Modular Ampliers

The Crestron

Modular Amplier Series can be congured for individual module use on a at surface or

ganged together (one or more modules) with the slide-lock system for installation in a 1U rack space.

The ampliers are functionally similar to each other with varying capabilities. For simplicity within this

guide, the term “amplier” is used except where noted.

DO Assemble the Device

If a single amplier is to be used on a at surface, refer to “Placing onto a Flat Surface.” Otherwise,

continue below for instructions on creating an amplier assembly that can be placed in a standard

equipment rack. The only tools needed are a #1 or # 2 Phillips screwdriver, and a 1/4" nut driver.

Gang Ampliers Together

Perform the following procedure to gang ampliers together. Refer to the diagrams.

1. Remove the two screws securing rail 1 to the amplier (unit 1).

2. Remove rail 1 from unit 1 by sliding it off the side of the amplier.

3. Attach rail 1 to unit 2 using the three included Phillips-head screws. Make sure that the screw

holes on the underside of rail 1 are on the bottom.

NOTE: Do not remove rail 2.

4. Slide unit 1 into the unit 2 assembly.

5. Secure unit 1 to the unit 2 assembly with the two screws removed in step 1.

6. Repeat steps 1 through 5 for additional ampliers.

Congure for Rack Installation

Before an amplier can be installed in a rack, additional hardware must be installed.

Assemble Faceplates

When an amplier or group of ampliers is not wide enough to mount in a rack, faceplates must be

assembled to “widen” the amplier to t. Assemble a faceplate by attaching an extrusion plate to a

quarter-width or half-width rack ear, as shown in the following diagrams. Secure the extrusion plate to

the rack ear using a 1/4" nut driver and the included nuts.

Attach Rack Ears to Ampliers

Attach the faceplate bracket(s) or rack ears, as required, to the amplier(s). Refer to the following

diagram for details.

NOTE: Do not attach faceplates to rack ears that are attached to the length of the amplier.

DO Install the Device

Once assembled, the amplier can be mounted into a rack, mounted onto a at surface, or placed onto

a at surface.

Mount into a Rack

Each amplier occupies 1U of rack space. Using a #1 or #2 Phillips screwdriver, mount the device into

the rack using four mounting screws (not included).

Mount onto a Flat Surface

1. Install the wall mount brackets with three Phillips-head screws (included) per side.

2. Secure the amplier to a at surface using four mounting screws (not included).

Place onto a Flat Surface

Attach the included feet to place the amplier(s) on a at surface.

DO Check the Box

QUANTITY ITEM PART NUMBER

1 Attenuator Cover, Magnetic, Security 4525789

2 Bracket, Wall Mount 2046992

1 Connector, 5-Pin 2003577

1 Extrusion Plate, Half-Width 4525245

1 Extrusion Plate, Quarter-Width 4525244

4 Foot, 0.5" x 0.5" x 0.23", Adhesive 2002389

4 Nut, 04-40, Keps 2004878

1 Power Cord, 6' 7" (2 m) 20 01134

1 Rack Ear, 1U, Half-Width 2046652

1 Rack Ear, 1U, Quarter-Width 2046651

6 Screw, 6-32 x 3/8", Undercut Head, Phillips 2007235

AMP-150 -70, AMP-15 0-10 0, AMP-1200-70, and AMP-120 0-100 Only

1 Connector, 2-Pin 2044402

AMP-225, AMP-2100, AMP-2100-70, and AMP-2100-100 Only

2 Connector, 2-Pin 2044402

Remove these

screws.

Unit 1

Rail 1

Unit 1

Rail 1

Unit 2

Rail 2

Rail 1

Unit 1

Unit 2 assembly

Unit 1

Unit 2 assembly

Quarter-size rack ear

(no faceplate attached)

Half-size faceplate bracket

Quarter-size faceplate bracket Half-size faceplate bracket

Produkt Specifikationer

Mærke:	Crestron
Kategori:	Modtager
Model:	AMP-2100-70

Har du brug for hjælp?

Hvis du har brug for hjælp til Crestron AMP-2100-70 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Crestron Manualer

Crestron DM-RMC-100-S Manual

24 September 2025

Crestron DM-RMC-200-C Manual

24 September 2025

Crestron AMP-X750 Manual

24 September 2025

Crestron AMP-X1000 Manual

23 September 2025

Crestron AMP-X75 Manual

23 September 2025

Crestron AMP-4600 Manual

23 September 2025

Crestron AMP-8075 Manual

23 September 2025

Crestron AMP-X300 Manual

23 September 2025

Crestron AMP-X500 Manual

23 September 2025

Crestron AMPI-8150 Manual

23 September 2025

Modtager Manualer

Nyeste Modtager Manualer

Nady PRA-8 Manual

4 November 2025

Blustream SP24AB-8K Manual

4 November 2025

DS18 FRP-8K Manual

4 November 2025

DS18 FRP-1.2K4 Manual

4 November 2025

Fosi Audio BOX X1 Manual

4 November 2025

BINIZE AO-BOX Manual

4 November 2025

Kohler K-99696-NA Manual

3 November 2025

Sommer 4796V000 Manual

3 November 2025

PEMP E70 Manual

3 November 2025

Taramp’s The Big Boss 8 Bass Manual

3 November 2025