Crunch PZ2-4030.1D Manual

Crunch Modtager PZ2-4030.1D

Læs gratis den danske manual til Crunch PZ2-4030.1D (2 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Crunch PZ2-4030.1D, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Place terminal in a secure

position so that it won’t

accidentally contact the

negative battery post

Power / Ground

cable size

It is critical to use the proper

power and ground cable. Select

the size listed here for your

amplier model. Always use high

quality copper cable.

Cable size recommendations for

multi amp systems are available

on our website.

Properly route power,

speaker and RCA cables

through the vehicle.

Choose a mounting location

that will provide adequate air

ventilation. Mount the amplier to

a secure surface. Do not mount

the amplier upside down.

Bare metal

Connect the RCA cables to

the INPUT connectors. The

OUTPUT can be used to

provide input for a second

amplier.

Connect the power cable to the

positive battery terminal. The

power cable must be fused

within 18 inches of the battery

terminal.

Re-connect the negative

battery terminal making sure it

is securely tightened.

The chassis ground connection

is critical to the performance

of the amplier. Choose a

location that is close to the

amplier. Completely scrape

away the paint and use a nut

and bolt if possible.

DO NOT USE AN EXISTING

FACTORY BOLT!

Disconnect

negative battery

terminal

Run Cables

Mount Amplier

Signal Input

Low Level RCA

Positive Battery

Connection

Re-connect

Negative Battery

Terminal

Chassis Ground

Be prepared to disarm your vehicle’s alarm and

to enter your radio / source unit code.

Installation

Before you start

CAUTION

Many new and factory radios require a reset code when

disconnected from battery power. This is an anti-theft

feature. Before unplugging power, you must determine if

your radio/source unit requires a reset code. Check the

operation manual for your vehicle or contact the dealer.

Turn the LEVEL control completely

counter-clockwise to minimum.

Level Control

4ga

Model Fuse Size Cable Size

PZ2-1530.1D

PZ2-2030.1D

PZ2-3030.1D

PZ2- 4030.1D

PZ2-1030.2D

PZ2-1530.2D

PZ2-2030.2D

PZ2-1530.4D

PZ2-2030.4D

PZ 2-2030. 5D

External 60A

External 80A

External 125A

External 150A

External 40A

External 50A

External 10 0A

External 40A

External 60A

External 10 0A

Using spade terminals, connect the

+12V to the power cable from the

battery, the REM to the source unit

turn-on wire and the GND to the

chassis ground..

Using spade terminals,connect

the speaker cables to the speaker

output connectors. Follow the

diagram below that best ts your

speaker conguration.

Power

Connections

Speaker

Connections

Stereo

Monoblock single woofer multiple woofersMonoblock

Bridged

SPEAKER

CH2CH1

BRIDGED

OUTPUT

CH2CH1

BRIDGED

PEAKER OUTPUT

S EAKER OUTPUT

SPEAKER OUTPUT

CH1 CH2

POWER

The HI INPUT is for use with source

units that do not offer RCA outputs.

Use the supplied harness to connect

to the source unit’s speaker output.

Signal Input

High Level

HI-INPUT

CH1

+- - +

CH2

The information contained within this document is intended to offer some basic guidelines

for a few of the most common installations. More complex audio systems should be

installed by a competent professional. Additional installation information available at

www.maxxsonics.com

6V 0.2V

LEVEL

Crunch products are designed and engineered in the USA by

www.maxxsonics.com

WARRANTY

Maxxsonics, LLC. warrants this product, to the original consumer purchaser, to be free from

defects in material and workmanship for a period of one (1) year from the date of purchase.

Maxxsonics, LLC. will, at it’s discretion, repair or replace defective products during the warranty period. Components

that prove to be defective in materials and workmanship under proper installation and use must be returned to

the original authorized Maxxsonics, LLC. retailer from where it was purchased. A photocopy of the original receipt

must accompany the product being returned. The costs associated with removal, re-installation and freight are

not the responsibility of Maxxsonics, LLC. This warranty is limited to defective parts and specically excludes

any incidental or consequential damages connected therewith. To view the full warranty, please visit the website.

CR PZ2 2021 QSG 01 - rev1

Quick Start

Installation Guide

Congratulations on your choice of a Crunch amplier. This

“Quick Start Installation” guide is meant to help you “hook

up” and play music. For more detailed information, on

system setting, speaker and subwoofer conguration and

full specications by model visit the website,

http://crunchcaraudio.com/manuals

PZ2-1530.1D

PZ2-2030.1D

PZ2-3030.1D

PZ2-4030.1D

PZ2-1030.2D

PZ2-1530.2D

PZ2-2030.2D

PZ2-1530.4D

PZ2-2030.4D

PZ2-2030.5D

Common System Setup

2ch - Full Range

4ch - Full Range

4ch - Mixed Mono

5ch

Mono

40Hz 300Hz10Hz 40Hz

LPF/HPF

LPF

HPF LPF FULL

40Hz 400Hz

CH1 CH2 CH3 CH4

CH1 CH2

HPF LPF FULL

CH1 CH2 CH3 CH4 CH5

CH 1/2

CH 5

CH 3/4

AT- U-01

6V 0.2V

LEVEL

40 300Hz

LPF

0 12dB

BASS

BOOST

0 12dB

SUBSONIC

40 400Hz

HPF

6V 0.2V

LEVEL

6V 0.2V

LEVEL

40 400Hz

HPF

Setup

The input MODE switch will “sum” or

combine the right and left channel signals

in the MONO position to improve bass

performance. Select MONO only when the

amp is being used for subwoofers.

The XOVER Mode switch sets the type

of crossover that will be active. 4 channel

models will have two switches, one for each

set of channels.

The HPF(high pass lter) control will limit the

output below the selected frequency. This

is typically used to protect midrange and hi

frequency speakers from damage and to

allow a smooth transition from a subwoofer.

The LPF(low pass lter) control will limit

output above the selected frequency. This

is used to allow a smooth transition to the

higher frequency speakers.

1. If possible, with the source unit off, conrm that the primary volume control is

turned down (counter clockwise).

2. Turn on the source unit (CD, or MP3 player). Re-conrm that the volume is

turned down. Make sure the source unit controls; balance, fader, bass and

treble are all set to center or “0” adjustment. Make sure that the green LED on

the end of the amplier is illuminated.

3. Play a clean musical selection of which you are very familiar. CD is preferred.

Do not use radio signals for level setting. Hit play and start turning the volume

of the source unit up.

4. Stop increasing the source unit volume when you reach 3/4 (about 75%) or until

you hear speakers begin to slightly start producing distortion.

5. Increase the amplier level (clockwise) until distortion is heard, then back

the level down (counter clockwise) until the distortion is eliminated. Small

adjustments may need to be made to balance the levels of multiple ampliers.

The BASS BOOST or BASS EQ control

will increase the output at 45Hz for more

pronounced bass. Exercise caution.

Increase the level in small amounts until

distortion is noticed, then back off a little.

Some models include a bass

remote. Avoid adjusting the bass

remote while operating vehicle.

Input Mode

Xover Mode

High pass

Adjustment

Low pass

Adjustment

Bass Boost

Remote Level

Control

This is a critical step to insure your amplier

is properly adjusted to match the signal

output level of your source unit.

THIS IS NOT A VOLUME CONTROL!

Level Setting

MONO STEREO

MODE

FULL LPF HPF

XOVER

60Hz 1.2KHz

HPF

30Hz 250Hz

LPF

0dB 9dB

BASS

BOOST

6V 0.2V

LEVEL

0dB 12dB

40Hz 400Hz

30Hz 250Hz

HPF LPF FULL

MONO STEREO

Produkt Specifikationer

Mærke:	Crunch
Kategori:	Modtager
Model:	PZ2-4030.1D

Har du brug for hjælp?

Hvis du har brug for hjælp til Crunch PZ2-4030.1D stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Crunch Manualer

Crunch Gravity GTX1600.4D Manual

8 Juni 2025

Crunch Gravity GTX2400.4D Manual

8 Juni 2025

Crunch DR-1325.4D Manual

6 September 2024

Crunch DR-2525.4D Manual

6 September 2024

Crunch DR-1325.1 Manual

6 September 2024

Crunch DR-3725.1D Manual

6 September 2024

Crunch DR-2725.1D Manual

6 September 2024

Crunch DR-2125.1D Manual

6 September 2024

Crunch DR-2125.2D Manual

6 September 2024

Crunch PZ2-3030.1D Manual

20 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Planet Audio TR4000.1D Manual

15 Juni 2025

Planet Audio PL3000.1D Manual

15 Juni 2025

Planet Audio PSX18 Manual

15 Juni 2025

Planet Audio MB600.2D Manual

15 Juni 2025

Planet Audio AC1600.4 Manual

15 Juni 2025

Planet Audio PL2400.4 Manual

15 Juni 2025

Rane Zone Power Eight Manual

14 Juni 2025

Blaupunkt Melbourne 130 Manual

14 Juni 2025

NVX NDA12001 Manual

14 Juni 2025

Denon AVC-1930 Manual

14 Juni 2025