CyberPower BR700ELCD Manual

CyberPower Uafbrydelig strømforsyning (UPS) BR700ELCD

Læs gratis den danske manual til CyberPower BR700ELCD (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 70 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 35.5 anmeldelser. Har du et spørgsmål om CyberPower BR700ELCD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

BR700ELCD / BR1000ELCD / BR1200ELCD

User’s Manual

K01-C000108-03

This manual contains important instructions that should be followed during installation and maintenance of

the UPS and batteries. Please read and follow all instructions carefully during installation and operation of

the unit. Read this manual thoroughly before attempting to unpack, install, or operate.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker

protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to de-energize this

equipment, turn off and unplug the UPS.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does

not sell products for life support or medical applications. use in any circumstance that would affect DO NOT

the operation or safety of any life support equipment, with any medical applications, or patient care.

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is

disconnected.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor

area, free of conductive contaminants. (Please see specifications for acceptable temperature and humidity

range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. There

are no user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before

servicing the battery or installing a computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of fire, do not use with or near

aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause

the machine to short out.

CAUTION! DO NOT USE WITH LASER PRINTERS! The power demands of laser printers are too large for

a UPS.

UNPACKING

The box should contain the following:

(1) UPS Unit x 1; (2) Phone Line x 1; (3) USB Cable x 1; (4) User Manual x 1; (5) Cable Collector x 1;

(6) Warranty Card x 1;

*PowerPanel® Personal Edition software is available on our website. Please visit www.cyberpower.com and

go to the Software Section for free download.

OVERVIEW

The BR700ELCD/ BR1000ELCD/ BR1200ELCD provides automatic voltage regulation for inconsistent utility

power. The BR700ELCD/ BR1000ELCD/ BR1200ELCD features 125 Joules of surge protection, and

provides battery backup during power outages. The BR700ELCD/ BR1000ELCD/ BR1200ELCD ensures

consistent power to your computer system and its included software will automatically save your open files

and shutdown your computer system during a utility power loss.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor, and peripheral

equipment does not exceed 700VA/1000VA/1200VA.

2. Ensure that the equipment plugged into the battery power-supplied/surge outlets does not exceed the

UPS unit's rated capacity (700VA/420W forBR700ELCD,1000VA/600W for BR1000ELCD,

1200VA/720W for BR1200ELCD). If the rated unit capacities are exceeded, an overload condition may

occur and cause the UPS unit to shut down and the circuit breaker to trip.

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8

hours is recommended to ensure that the battery's maximum charge capacity is achieved. Charge loss

may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC

outlet. The unit will charge in both the on and off position.

2. If you will use the software, connect the USB cable to the USB port on the UPS.

3. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data

storage device (Zip drive, Jazz drive, Tape drive, etc. into the battery power supplied outlets. DO NOT

plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device

into the UPS. The power demands of these devices will overload and possibly damage the unit.

4. To protect a fax, telephone, modem line or network cable, connect a telephone cable or network cable

from the wall jack outlet to the IN jack of the UPS. Then connect a telephone cable or network cable from

the OUT jack on the UPS to the modem, computer, telephone, fax machine, or network device.

5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc.) Avoid using extension cords.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will

"beep".

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait

10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the

battery will automatically recharge.

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the

battery every three months to ensure battery life.

DESCRIPTION

1. Power Switch

Press the switch for two seconds to turn the UPS ON or OFF.

2. LCD Display Selected Switch

The switch can be used to select the LCD display contents including Input Voltage, Output Voltage and

Estimated Run Time. The toggle frequency is set to one time per second. Holding the switch for more than

two seconds while running on battery will silence the buzzer.

3. LCD Display

High resolution and intelligent LCD display shows all the UPS information with icons and messages. For

more information please review the “Definitions for Illuminated LCD Indicators” section.

4. Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network cable from

surge and spikes.

5. AC Outlets

The UPS provides 4 outlets for connected equipment to insure temporary uninterrupted operation during a

power failure and against surges and spikes and another 4 outlets against surges and spikes only.

6. USB Charger Port

The UPS provides charging for external equipment via this port.

7. Cable Collector

Collect the cables connected from the AC outlets in the cable collector.

8. Led Indicators

The power on LED lights up when the UPS is ON.

9. USB Port To PC

This port allows connection and communication from the USB port on the computer to the UPS unit. The

UPS communicates its status to the PowerPanel® Personal Edition software.

10. Input Circuit Breaker

The Circuit Breaker provides optimal overload protection.

11. Input Power Cord

Connect to utility power

Model BR700ELCD-UK BR1000ELCD-UK BR1200ELCD-UK

Capacity (VA) 700VA 1000VA 1200VA

Capacity (Watts) 420W 600W 720W

Input

Input Voltage Range 165-290Vac

Frequency Range 47~63Hz (Auto Sensing)

AVR Function Boost @ 200+/-10V

Output

On Battery Output Voltage Simulated Sine Wave at 230Vac +/-10%

On Battery Output Frequency 50/60Hz +/-1%

Transfer Time 4ms Typical

Overload Protection On Utility: Circuit Breaker and Internal Current Limiting

On Battery: Internal Current Limiting

Surge Protection

Lightning / Surge Protection Yes

Network/ Phone/ Fax/ Modem

Protection RJ11/RJ45 (One In/ One Out)

Operating Temperature +32F to 104F ( 0C to 40C )

Physical

Total # of UPS outlets 6 (3 for battery backup and surge, 3 for surge only)

Dimensions (WxHxD) (mm) 166x 118x288

Weight (kg) 5.3 6.5 8.2

Wall-mounted Distance(mm) 163

Battery

Sealed Maintenance Free

Lead Acid Battery RBP0083 RBP0006 RBP0063 x 1 x 1 x 2

Typical Recharge Time 8 hours

User Replaceable Yes

Status Indicators

Indicators Power On, LCD Display

Audible Alarms On Battery, Low Battery, Overload

Communication

PowerPanel

Personal Edition

Software Windows 8/7/Vista/XP/2000,Server 2012/2008/2003, Linux

Management

Auto-Charger Yes

Auto-Restart Yes

USB interface Yes

TECHNICAL SPECIFICATIONS

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	BR700ELCD
Bredde:	166 mm
Dybde:	288 mm
Højde:	118 mm
Vægt:	5300 g
Produktfarve:	Sort
Skærmtype:	LCD
USB-port:	Ja
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Responstid:	4 ms
Opbevaringstemperatur (T-T):	-20 - 50 °C
Relativ luftfugtighed ved drift (H-H):	0 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	0 - 90 %
Ethernet LAN-porte (RJ-45):	2
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 40 °C
Husmateriale:	Plast
Udgangseffekt:	420 W
Certificering:	CE\nRoHS
LED-indikatorer:	Ja
Opladningstid for batteri:	8 t
Medfølgende software:	PowerPanel® Personal Edition
Driftshøjde:	0 - 3000 m
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
Nominel udgangsspænding:	230 V
Modem-porte (RJ-11):	2
AC udgange, antal:	6 AC stikkontakt(er)
Overspænding energivurdering:	125 J
Indgående driftsspænding (maks.):	290 V
Output strømkapacitet (VA):	0.7 kVA
Indgående driftsspænding (min.):	165 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	- V
UPS topologi:	Interaktivt indgangsstik
Beskyttelsesfunktioner mod strømstød:	Digital Subscriber Line (DSL), Fax, Modem, Network, Telephone
Beskyttelse ved overspænding:	Ja
Bølgeform:	Sine
Hørbare alarmtilstande:	Alarm when on battery, Fault, Low battery alarm, Overload alarm
Typisk backup tid ved halv styrke:	6 min.
Typisk backup tid ved fuld styrke:	2 min.
Koldstart:	Ja
Seriegrænseflade:	Ingen
Automatisk spændingsregulering (AVR):	Ja
Uddgående frekvens:	50/60 Hz
EMI/RFI støjfiltrering:	Ja