CyberPower CP550EPFCLCD Manual

CyberPower Uafbrydelig strømforsyning (UPS) CP550EPFCLCD

Læs gratis den danske manual til CyberPower CP550EPFCLCD (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 44 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 22.5 anmeldelser. Har du et spørgsmål om CyberPower CP550EPFCLCD, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

CP550/ 13900/ 00/1500EPFCLCD

User’s Manual

K01- -030000460

This manual contains important safety instructions. Please read and follow all instructions carefully during

installation and operation of the unit. Read this manual thoroughly before attempting to unpack, install, or

operate your UPS.

CAUTION! The UPS must be connected to a grounded AC power outlet with fuse or circuit breaker

protection. DO NOT plug the UPS into an outlet that is not grounded. If you need to -energize this de

equipment, turn o and unplug the UPS.

CAUTION! DO NOT USE FOR MEDICAL OR LIFE SUPPORT EQUIPMENT! CyberPower Systems does

not sell products for life support or medical applications. use in any circumstance that would aect DO NOT

the operation safety of life support equipment, medical applications, or patient care. and

CAUTION! Hazardous live parts inside can be energized by the battery even when the AC input power is

disconnected.

CAUTION! To prevent the risk of re or electric shock, install in a temperature and humidity controlled indoor

area, free of conductive contaminants. (Please see specications for acceptable temperature and humidity

range).

CAUTION! To reduce the risk of electric shock, do not remove the cover, except to service the battery. There

are no user serviceable parts inside, except for the battery.

CAUTION! To avoid electrical shock, turn o the unit and unplug it from the AC power source before

servicing the battery or installing a computer component.

CAUTION! DO NOT USE WITH OR NEAR AQUARIUMS! To reduce the risk of re, do not use with or near

aquariums. Condensation from the aquarium can come in contact with metal electrical contacts and cause

the machine to short out.

DO NOT USE THE UPS ON ANY TRANSPORTATION! To reduce the risk of re or electric shock, do not

use the unit on any transportation such as airplanes or ships. The eect of shock or vibration caused during

transit and the damp environment can cause the unit to short out.

UNPACKING

The box should contain the following:

(1) UPS Unit 1; (2) USB Cable x User Manual 1; ) Function Setup Guide x 1 ; (5 Power Cord x 1; (3) x (4 )

(Type and quantity may dier from models.)

OVERVIEW

The 1300/1500EPFCLCD provides automatic voltage regulation for inconsistent utility power. CP550/900/

The 900/1300/1500EPFCLCD features Joules of surge protection, and provides battery backup CP550/ 405

during power outages. The 900/1300/1500EPFCLCD s consistent power to your computer CP550/ ensure

system and its included software will automatically save your open les and shut down your computer

system during a utility power loss.

SUPPORTS Active PFC POWER SUPPLIES

This CyberPower UPS system supports High Eciency power supplies with Active Power Factor Correction

(Active PFC). Active PFC is used to improve the eciency of power delivery. The current US Energy Star®

Program Requirements for Computers mandates Active PFC for all power supplies over 100 watts.

Additionally, programs such as 80 Plus® are often used to identify high eciency power supplies with Active

PFC.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor, and peripheral

equipment does not exceed t 550VA/he 900VA/ VA/ . 1300 1500VA

2. Ensure that the equipment plugged into the battery power-supplied/surge outlets does not exceed the

UPS unit's rated capacity ( A/350W for CP550EPFCLCD, 550V 900VA/540W for CP900EPFCLCD,

1300 780VA/ W for CP1300EPFCLCD, VA/ W for CP1500EPFCLCD). If the rated unit capacities 1500 900

are exceeded, an overload condition may occur and cause the UPS unit to shut down the circuit or

breaker to trip.

DESCRIPTION

1. Power Switch

Used as the master on/o switch for equipment connected to the battery power supplied outlets.

2. Power On Indicator

This LED is illuminated when the utility power is normal and the UPS outlets are providing power, free of

surges and spikes.

3. LCD Module Display

High resolution and intelligent LCD display shows all the UPS information with icons and messages. For

more information, please check the “Definitions for Illuminated LCD Indicators” section.

4. Display Switch

The switch can be used to select the LCD display contents including Input Voltage, Output Voltage and

Estimated Run Time. The toggle frequency is set to one time per 0.5 second. Press the switch to roll

down the function menu. Pressing the switch for 2 seconds will turn the LCD display on or o while in

AC/Utility power mode.

5. Silence Alarm Switch

The toggle frequency is set to one time per 0.5 second. Press the switch to roll up the function menu.

Holding the switch for more than 2 seconds will silence the buzzer.

6. Control Switch

Press the Control switch for 3 seconds in AC/Utility Power Mode to perform a Self Test of the battery.

7. USB Charging Ports

The USB Power ports provide 5V 1A power output. 2.

8. Communication Protection Ports RJ45

Communication protection ports will protect network cable from surge and spikes.

9. USB Port to PC

This port allows connection and communication from the USB port on the computer to the UPS unit. The

UPS communicates its status to the PowerPanel

® Personal Edition software.

10. Serial Port to PC

This port allows connection and communicat from the DB-9 serial on the computer to the UPS unit. es

The UPS communicates its status to the PowerPanel® Personal Edition software.

NOTE: Only one of these two ports can be used as communication and control of the UPS unit at one

time.

11. Battery and Surge Protected Outlets

The unit has several battery powered/surge suppression outlets for connected equipment to ensure

temporary uninterrupted operation of your equipment during a power failure. Check the type and quantity

of outlets for different models in the following table. (DO NOT plug a laser printer, paper shredder,

copier, space heater, vacuum, sump pump or other large electrical devices into the Battery and “

Surge Protected Outlets The power demands of these devices may overload and damage the ”.

unit.)

Model

NEMA

Outlet

Type

Quantity

*CP900EPFCLCD-AU has 3 Battery and Surge Protected Outlets and 3 Surge protected outlets

12. Circuit Breaker

Located on the back of the UPS, the circuit breaker serves to provide overload and fault protection.

13. AC Input

Connect the AC Power cord to a properly wired and grounded outlet.

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8

hours is recommended to ensure that the battery's maximum charge capacity is achieved. Charge loss

may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC

outlet. The unit will charge in both the on and o position.

Note: This UPS is designed with a safety feature to keep the system from being turned on during shipment.

The rst time you turn the UPS , you will need to have it connected to AC power or it will not power up. on

2. If you will use the software, connect the USB cable to the USB port on the UPS.

3. With the UPS unit o and unplugged, connect the computer, monitor, and any externally powered data

storage device (Zip drive, Jazz drive, Tape drive, etc. )into the battery power supplied outlets. DO NOT

plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device into the

battery power supplied outlets. The power demands of these devices will overload and possibly damage

the unit.

4. To protect network cable, connect a network cable from the wall jack outlet to the IN jack of the UPS. Then

connect network cable from the OUT jack on the UPS to the mputer or network device. co

5. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is

protected by a fuse or circuit breaker and does not service equipment with large electrical demands (e.g.

air conditioner, refrigerator, copier, etc. Avoid using extension cords.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate and the unit will

"beep".

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait

10 seconds. Make sure the circuit breaker is depressed and then turn the UPS on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the

battery will automatically recharge.

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully

charged. Recharge the battery every three months to ensure battery life.

11.

CyberPower’s Green Commitment

CyberPower is dedicated to the development of green products, and has adopted

Green practices throughout its business, including: membership in Climate Savers

Computing Initiative (CSCI), accordance with the Restriction on Hazardous

Substances (RoHS), Waste Electrical and Electronic Equipment (WEEE) protocols,

as well as ISO 14001 and IECQ QC080000. CyberPower pledges to provide the

advanced energy solution for the environment and become a leading eco-friendly

organization in the UPS industry.

Reduce Energy Cost with GreenPower UPSTM Technology

CyberPower’s goal is not only to provide eco-friendly products but also to bring the best value for consumers.

The advanced energy-saving design improves the operating efciency and eliminates waste energy

consumption As a result, consumers will enjoy signicant energy cost savings with the adoption of.

GreenPower UPSTM technology.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

IMPORTANT SAFETY INSTRUCTIONS

BATTERY REPLACEMENT

HARDWARE INSTALLATION GUIDE

CYBERPOWER GREENPOWER UPS™ TECHNOLOGY

CP550/900EPFCLCD

CP1300/1500EPFCLCD

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	CP550EPFCLCD
Bredde:	100 mm
Dybde:	275 mm
Højde:	230 mm
Vægt:	6800 g
Produktfarve:	Sort
Kontroltype:	Knapper
Batterispænding:	12 V
Batterikapacitet:	7 At
Skærmtype:	LCD
Pakkevægt:	7600 g
Pakkedybde:	365 mm
Pakkebredde:	195 mm
Pakkehøjde:	335 mm
USB-port:	Ja
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Mini Tower
Responstid:	4 ms
Ethernet LAN-porte (RJ-45):	2
Antal USB 2.0-porte:	1
Støjniveau:	35 dB
Udgangseffekt:	350 W
LED-indikatorer:	Status
Harmoniseret systemkode (HS):	8504408590
Batteritype:	RBP0078
Opladningstid for batteri:	8 t
Bæredygtighedscertifikater:	CE, EAC, RCM, RoHS
Oprindelsesland:	Kina
Indgangsfrekvens:	50/60 Hz
Overholdelse af bæredygtighed:	Ja
Varmeafgivelse:	31 BUT/t
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Over voltage, Overload, Under voltage
Effektivitet:	98.5 %
USB porttype:	USB Type-B
Strømstik:	C14 forbinder
AC udgange, antal:	6 AC stikkontakt(er)
Overspænding energivurdering:	405 J
Indgående driftsspænding (maks.):	270 V
Output strømkapacitet (VA):	0.55 kVA
Indgående driftsspænding (min.):	170 V
Udgangs driftsspænding (min.):	203 V
Udgangs driftsspænding (maks.):	230 V
UPS topologi:	Interaktivt indgangsstik
Beskyttelse ved overspænding:	Ja
Bølgeform:	Sine
Hørbare alarmtilstande:	Alarm when on battery, Low battery alarm, Overload alarm
Automatisk batteritest:	Ja
Automatisk genstart:	Ja
Automatisk spændingsregulering (AVR):	Ja
Uddgående frekvens:	50/60 Hz