CyberPower CPS1000AVR Manual

CyberPower Uafbrydelig strømforsyning (UPS) CPS1000AVR

Læs gratis den danske manual til CyberPower CPS1000AVR (13 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om CyberPower CPS1000AVR, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/13

CPS1000AVR

Guaranteed Uninterruptible Power System

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Make sure that the total Volt-Amp (VA) requirements of your computer, monitor and peripheral equipment does

not exceed 1440VA.

2. Insure that the equipment plugged into the three battery power-supplied outlets does not exceed the UPS unit’s

rated capacity (1000VA/500W for CPS1000AVR). If rated unit capacities are exceeded, an overload

condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

3. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or

Amps (A) into VA by doing the calculations below. Note: The below equation only calculates the maximum

amount of VA that the equipment can use, not what is typically used by the equipment at any one time. Users

should expect usage requirements to be approximately 60% of below value.

TO ESTIMATE POWER REQUIREMENTS:

Watts (W) x 1.82 = VA or Amps (A) x 120 = VA

Add the totals up for all pieces of equipment and multiply this total by .6 to calculate actual requirements There are

many factors that can affect the amount of power that your computer system will require. The total load that you will

be placing on the battery-powered outlets should not exceed 80% of the unit’s capacity.

INSPECTION

The box should contain the following:

(1) PowerPanel Plus™ software (floppy disk); (1) serial interface cable (DB-9); (1) serial to USB adapter cable; (1) telephone

communication cable; (1) user manual; (1) warranty registration card; (1) UPS unit.

DESCRIPTION

HARDWARE INSTALLATION GUIDE

7. Electrical Wiring Fault Indicator

This LED indicator will illuminate to warn the user

that a wiring problem exists with the AC outlet.

If this LED is illuminated, user is advised to

unplug all electrical equipment from the outlet and

have an electrician check the outlet to insure

proper wiring.

8. AVR Indicator

This LED indicates that the UPS is operating in

automatic voltage regulation mode.

9. Using Battery Indicator

This illuminates during a utility failure, indicating

that the battery is supplying power to the battery

power supplied outlets.

10. Check Battery

This illuminates indicating a weak battery. If the

indicator is still illuminated after allowing the unit

to charge for 12 hours, replace the battery

according to the instructions in the Replacing the

Battery section of this manual.

11. Serial Port to PC

This port allows connection and

communication from the DB-9 serial or USB port

on the computer to the UPS unit. The UPS

communicates its status to the PowerPanel

Plus™ software. This interface is also

compatible with the UPS service provided by

Windows NT, Windows 2000 and Windows XP.

12. Communication Protection Ports

Communication protection ports will protect any

standard modem, fax, or telephone line.

1. Battery Backup and Surge Protection Outlets

Provides three battery-supplied outlets with

Automatic Voltage Regulation for consistent output

power to connected equipment.

2. “Always-On” Surge Protection Outlets

Provides three surge-protected outlets to protect

connected equipment against surges and spikes.

3. All outlets Designed for AC Adapters

Allows six AC power adapter blocks to be plugged

into the UPS without making adjacent outlets

inaccessible.

4. Resettable Circuit Breaker

Located on the side of the UPS, the circuit breaker

provides circuit overload and fault protection.

Under normal operating conditions, the circuit

breaker is depressed.

5. Power Switch

Can be used as the master on/off switch for

computer equipment connected to the battery power

supplied outlets.

6. Power On Indicator

This LED is illuminated when the utility condition is

normal and the UPS outlets are providing “clean”

power, free of surges and spikes.

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least four

hours is recommended to insure that the battery’s maximum charge capacity is achieved. Charge loss may

occur during shipping and storage. To recharge the battery, simply leave the unit plugged into an AC outlet.

The unit will charge in both the on, as well as the off, position.

2. If you wish to use the software, connect either the enclosed serial

interface or USB adapter cable to the serial port on the UPS and an

open serial or USB port on the computer. If you are not going to

use the software, you do not need to connect a cable.

3. With the UPS unit off and unplugged, connect your computer,

monitor, and any externally powered data storage device (Zip drive, Jazz

drive, Tape drive, etc…) into the battery power supplied outlets. Plug

your peripheral equipment (printer, scanner, speakers) into the full-time

surge protection outlets. DO NOT plug a laser printer, copier, space

heater, vacuum or other large electrical device into the UPS. The

power demands of these devices will overload and possibly damage

the unit.

4. To protect a fax, telephone or modem line, connect a telephone

cable from the wall jack outlet to the in jack of the UPS. Connect a

telephone cable the out-jack on the UPS with the CPU icon to the

modem port of the computer. The out-jack with the telephone icon

can be used to protect a telephone or fax machine line.

5. Plug the UPS into a properly grounded wall outlet. Make sure the

wall outlet is protected by a fuse or circuit breaker and does not

service equipment with large electrical demands (e.g. refrigerator, copier, etc…). Avoid using extension

cords. If used, the extension cord must be rated for 15 amps.

6. Depress the power switch to turn the unit on. The power on indicator light will illuminate.

7. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this,

turn the UPS off and unplug at least one piece of equipment from the battery power supplied outlets. Wait 10

seconds. Make sure the circuit breaker is depressed and then turn the UPS on.

8. Your UPS is equipped with an auto-charge feature. When the UPS is plugged into an AC outlet, the battery

will automatically recharge.

9. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

10. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the

battery every three months to insure battery life.

POWERPANEL PLUS™ SOFTWARE INSTALLATION GUIDE

(Note: Use of the software is optional. The UPS will provide surge suppression and battery backup without the

software. You must use the software if you wish to have the automatic shutdown feature).

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	CPS1000AVR

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower CPS1000AVR stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) CyberPower Manualer

CyberPower LX1500GU3 Manual

5 August 2025

CyberPower LX1325GU3 Manual

4 August 2025

CyberPower OL3000ERTXL2U Manual

22 Juli 2025

CyberPower OLS3000 Manual

22 Juli 2025

CyberPower OL1000ERTXL2U Manual

21 Juli 2025

CyberPower OLS1000EA Manual

21 Juli 2025

CyberPower PR3000ELCDSL Manual

21 Juli 2025

CyberPower OLS1500EA Manual

21 Juli 2025

CyberPower OLS3000EA Manual

21 Juli 2025

CyberPower PR1500ERTXL2U Manual

21 Juli 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

APC E3MCBC10B Manual

6 August 2025

APC Back-UPS BE700G3 Manual

5 August 2025

APC GVSBPIT75 Manual

5 August 2025

APC GVLMBCA200K500H Manual

4 August 2025

APC E3SBPAR10K40F Manual

4 August 2025

APC BE650G2-GR Manual

4 August 2025

4 August 2025

4 August 2025

4 August 2025

4 August 2025