CyberPower CyberShield CSN30C12V-E Manual

CyberPower Uafbrydelig strømforsyning (UPS) CyberShield CSN30C12V-E

Læs gratis den danske manual til CyberPower CyberShield CSN30C12V-E (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 52 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 26.5 anmeldelser. Har du et spørgsmål om CyberPower CyberShield CSN30C12V-E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

User’s Manual for

CyberShield

CSN30C12V-E

IMPORTANT SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important instructions regarding the installation and operation of this device.

Read this manual thoroughly before attempting to unpack , install or operate this device

CAUTION!

INSTALLATION

BATTERY REPLACEMENT

This battery is hot-swappable. As long as utility power is on , you may leave the Battery Backup

Power Supply and connected equipment on while replacing a new battery.

Step 1:

a. Remove the case screw.

b. Open the battery cover.

Step 2:

a. Loosen strap from battery.

b. Slide battery off of the shelf.

c. Remove battery cable connector.

Step 1:

a. Remove the case screw.

b. Open the battery cover.

Step 2:

a. Loosen the battery strap.

b. Disconnect battery cable connector

to remove battery.

c. Replace with new battery and

reconnect the battery connector.

Step 3:

a. Tighten the battery strap.

b. Close the battery cover and

lock the case screw.

CAUTION! Power Cable Selection:

A power cable (4.5m max.) being identified as 18AWG, "OUTDOOR" or "WATERPROOF"

should be selected while necessary.

CAUTION!

The battery can energize hazardous live parts inside even when the AC input power is

disconnected.

To reduce the risk of electric shock, keep the cover on. there are no user serviceable

parts inside the unit, including the battery. Please contact us or our dealer for service.

When replacing batteries, the replacement should have the same rating:

Listed/Certified Valve Regulated Lead Acid Battery, 12V, max. 9Ah.

CAUTION! Before replacing batteries, remove conductive jewelry, such as chains, watches and rings,

and use tools with insulated handles. High energy passed through conductive materials

can cause severe burns.

CAUTION! Don’t dispose of batteries in a fire. Batteries may explode if improperly disposed.

Recycle batteries in accordance with local regulations.

The UPS battery is charging when it’s connected to utility power. The battery is charging

during its first 24 hours of normal operation. Don’t expect full battery capacity during this

initial charging period.

CAUTION!

Step 3:

a. Use the enclosed installation template to mark an installation location for the unit.

b. The unit can only be wall-mounted in one direction with the connector facing down.

d. Tighten the screws to secure the unit.

e. Reconnect the battery cable connector and place the battery back.

CAUTION! Keep the gap around the UPS for air circulation.

CyberShield UPSs are designed to provide a local power solution for

cable telephony, wireless local loop (WLL), and fiber to the home

(FTTH) broadband equipment.

c. Mount the unit on the wall with 3 mounting screws into the keyhole slots.

13/32”

3/16”

Runtimes based on testing fully-charged, new batteries at normal operating conditions.

Runtime curve is approximate and varies based on battery age, level of charge at test,

environment, and other variables.

CAUTION!

OPERATION

Please refer to the following recommendations to connect equipment and power source.

Step3. Plug the UPS power cord into the utility power cord inlet.

Step4. Plug the UPS power cord into the wall outlet.

Step2. Refer to the to setup the connector and connect equipmentCOMMUNICATION SIGNALS

Step1. Refer to the to connect the battery. BATTERY REPLACEMENT

to the UPS.

To avoid electric shock, unplug power cable from the AC power source before servicing

the battery or installing a computer component.

CAUTION!

COMMUNICATION SIGNALS

The communication signals of this unit are isolated from the internal circuitry via open collector opto-

coupled transistors. The connection “SIG RTN” (Signal Return) is a common return point for all

communication signals. In the typical application, the attached equipment digital ground connects to

Signal Return, and pull-up resistors turn the open collector signals into logic levels.

12V

12V RTN

SIG RTN

ON BATTERY

REPLACE BATTERY

BATTERY MISSING

LOW BATTERY

+ Voltage output

- Voltage output

Signal return

Low when operating from utility line.

Open when operating from battery.

Low when battery is charged.

Open when battery fails the Self Test.

Low when battery is present.

Open when battery is missing.

Low when battery is near full charge capacity.

Open when operating from a battery with < 10% capacity.

Utility power cord inlet

Communication signals

MessageSignal

It is recommended to connect the unit to the required equipment and battery before

plugging in the utility power.

CAUTION!

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	CyberShield CSN30C12V-E

Har du brug for hjælp?

Hvis du har brug for hjælp til CyberPower CyberShield CSN30C12V-E stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Uafbrydelig strømforsyning (UPS) CyberPower Manualer

CyberPower ALT750EILCDRT1U Manual

6 December 2025

CyberPower OL1KRTHD Manual

5 December 2025

CyberPower OL3KRTHD Manual

3 December 2025

CyberPower OL750RTHD Manual

3 December 2025

CyberPower OL2K2RTHD Manual

2 December 2025

CyberPower RB1290X2D Manual

2 Oktober 2025

CyberPower HSTP3T30KEBCWOB Manual

20 August 2025

CyberPower RT33020KE Manual

20 August 2025

CyberPower Value2200EILCD Manual

20 August 2025

CyberPower OR1000ELCDRM1U Manual

20 August 2025

Uafbrydelig strømforsyning (UPS) Manualer

Nyeste Uafbrydelig strømforsyning (UPS) Manualer

Atlantis Land HostPower 1102 Manual

28 November 2025

MKC MK-2000UPS Manual

6 November 2025

Tripp Lite SMART1500RMXL2U Manual

6 November 2025

APC Smart-UPS SMT3000RMT2U Manual

30 Oktober 2025

ATen EC1000 Manual

28 September 2025

Riello SEP 1500 Manual

20 September 2025

Riello Dialog Vision Manual

20 September 2025

Panamax MB1000 Manual

4 September 2025

Panamax MB1500 Manual

4 September 2025

Akyga AK-ND-41 Manual

30 August 2025