CyberPower OP1500 Manual

CyberPower Uafbrydelig strømforsyning (UPS) OP1500

Læs gratis den danske manual til CyberPower OP1500 (8 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om CyberPower OP1500, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Office Tower Series with AVR UPS

OP1500AVR-T4

User Manual K01-1500A2A

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit.

Read this manual thoroughly before attempting to unpack, install, or operate your UPS.

. CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive

contaminants. (Please see specifications for acceptable temperature and humidity range).

CAUTION! To reduce the risk of electric shock, do not remove the cover except to service the battery. No user serviceable parts inside

except for battery.

CAUTION! UPS must be connected to an AC power outlet with fuse or circuit breaker protection. Do not plug into an outlet that is not

grounded. If you need to de-energize this equipment, turn off and unplug the unit.

CAUTION! To avoid electrical shock, turn off the unit and unplug it from the AC power source before servicing the battery or installing a

computer component.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

UPS Unit¯1; PowerPanel Plus Software Disk¯1; PowerPanel Software Disk¯1; Serial Interface Cable (DB-9)¯1; Telephone Cable¯1;

User Manual¯1; PowerPanel Plus Software User Manual¯1; PowerPanel Software User Manual¯1.

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS unit’s rated capacity (1500VA/950W).

If rated unit capacities are exceeded, an overload condition may occur and cause the UPS unit to shut down or the circuit breaker to trip.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert Watts (W) or Amps (A) into VA by doing

the calculations below. Note: The below equation only calculates the maximum amount of VA that the equipment can use, not what is

typically used by the equipment at any one time. Users should expect usage requirements to be approximately 60% of below value.

TO ESTIMATE POWER REQUIREMENTS

1. Watts (W) x 2.0 = VA or

Amps (A) x 120 =

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual requirements. There are many factors that can

affect the amount of power that your computer system will require. The total load that you will be placing on the battery-powered outlets

should not exceed 80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

1. Connect the equipment to your UPS outlets. Items such as copiers, laser printers, vacuums, space heaters, paper shredders, or other large

electrical devices should not be connected to the UPS. Please assure that the total load of your equipment is less than the maximum total

power capacity of your UPS.

2. Connect your UPS power cord into a two-pole, three-wire grounded

receptacle only. Please avoid using extension cords and adapter plugs.

(To maintain optimal battery charge, leave the UPS plugged in at all

times.)

3. Press the UPS power button to turn it on. The “Power On” indicator will

be illuminated in “Green”.

4. Install your optional software and accessories. To use the software,

simply connect the enclosed serial interface cable to the serial port on

the UPS and an open serial port on the computer.

BASIC OPERATION

FRONT PANEL DESCRIPTION

 Power Switch

Press the ON/OFF button to turn the UPS on or off.

 Test Switch

This UPS performs a self-test automatically when power is turned on. If the UPS passes the

test, it returns to on-line operation. If the UPS fails the self-test, please recharge the battery

for 4 hours and perform another self-test. If it fails after recharging, please replace the

batteries.

 Battery Indicators

These indicators are a visual indication of the battery charge. If battery capacity is under 20%, no indicator LED will illuminate

and the UPS will beep.

 Load Level Indicators

These LED indicators are a visual depiction of the UPS load. The load indicator LED will turn orange if the load is between 80

and 100%. If the load is under 20%, no indicator LED will illuminate.

 Wiring Fault Indicator

This LED indicator will illuminate to warn the user that a wiring problem exits with the AC outlet, such as bad ground, missing

ground or reversed polarity. If this is illuminated, the user is advised to disconnect all electrical equipment from the outlet and

have an electrician check the outlet to insure proper wiring.

 Using Battery Indicator

This illuminates during utility failure, indicating that the battery is supplying power to the battery-power supplied outlets.

 AVR Indicator

This LED indicates that the UPS is operating in automatic voltage regulation mode. When the LED is illuminated continuously,

it indicates input over-voltage and the UPS unit bucks the voltage. When the LED is flashed in rotation, it indicates that the

UPS unit is boosting input voltage.

 Power On Indicator

This LED is illuminated when the utility condition is normal and the UPS outlets are providing “clean power”, free of surges and

spikes.

REAR PANEL DESCRIPTION

 Battery Backup and Surge Protection Outlets

This unit provides 6 battery-powered, surge-protected and AVR outlets for connected equipment and insures

uninterrupted operation of connected equipment during a power failure.

 Circuit Breaker Reset for Overload Protection

Re-settable circuit breakers provide optimal overload protection.

 Communication Protection Ports

Combination RJ-45/RJ11 Protection Ports protect your Phone, Fax , Modem, or Ethernet device from surges over the Ethernet orPhone line.

 Serial Ports

The OP1500AVR-T4 provides two serial ports to allow connection and communication between the UPS and two computers. This allows the

simultaneous shutdown of two computer systems. These interfaces are also compatible with the UPS service provided by Windows 2000,

Windows NT, Windows XP, Windows Server 2003 and Mac OS 10X.

1. The Primary PC

To control the UPS and make any change to the operation of the UPS, please install

the PowerPanel Plus in your primary computer and then connect it to the Serial Port I of

the UPS.

2. The Secondary PC

The secondary computer with PowerPanel installed should be connected to the serial

port II. This PC will shutdown following the user settings in PowerPanel Software when a

power failure occurs.

When a power failure occurs, one of the following shutdown sequences will be executed:

1. If the Primary and Secondary serial ports are both in use: the Primary computer will start to count down (user controlled delay) for shutdown

(User Control delay can be set in the PowerPanel Plus software. Recommended time is 5 minutes). Once the Primary computer is shutdown,

the UPS will signal the Secondary computer and initiate the Secondary to shutdown. The UPS default shutdown time is 2 minutes. Therefore,

it is recommended that Secondary computer is set to shutdown within 1 minute in PowerPanel Software.

2. If only the Secondary serial port is in use: the Secondary computer will shutdown following the user settings in PowerPanel Software.

However, the Secondary computer will not able to signal the UPS to shutdown. Therefore, the UPS will only power off when it is in low

battery.

TROUBLE SHOOTING

Problem Possible Cause Solution

Batteries are not fully charged. Recharge the battery by leaving the UPS plugged in. The UPS does not perform

expected runtime. Battery is slightly worn out. Contact CyberPower Systems at tech@cyberpowersystems.com.

The on/off switch is designed to

prevent damage by rapidly

turning it off and on.

Turn the UPS off.

Wait 10 seconds and then turn the UPS on.

The unit is not connected to an

AC outlet.

The unit must be connected to a 110/120v 60Hz outlet.

The battery is worn out. Contact CyberPower Systems at tech@cyberpowersystems.com.

The UPS will not turn on.

Mechanical problem. Contact CyberPower Systems at tech@cyberpowersystems.com.

Circuit breaker is tripped due to

overload

Turn the UPS off and unplug at least one piece of equipment. Wait 10

seconds, reset the circuit breaker and then turn the UPS on.

Batteries are discharged Allow the unit to recharge for at least 4 hours.

Outlets do not provide

power to equipment

Unit has been damaged by a

surge or spike.

Contact CyberPower Systems at tech@cyberpowersystems.com.

The serial cable is not

connected. Connect the serial cable to the UPS unit and an open serial port on the back

of the computer. You must use the cable that came with the unit.

The serial cable is connected to

the wrong port.

Check the back of the computer for an additional serial port. Move the

cable to this port.

The unit is not providing battery

power. Shutdown your computer and turn the UPS off. Wait 10 seconds and turn the

UPS back on. This should reset the unit.

PowerPanel Plus™ is

inactive (all icons are gray).

The serial cable is not the cable

that was provided with the unit. You must use the cable that was included with the unit for the software and

the unit to be able to communicate.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

Power On

AVR

Using

Battery

Circuit

Breaker

Alarm

Condition

On Off Off Set Off Normal

On Slow flash Off Set Off AVR- Max. boost 13% of input voltage for output regulation while input

voltage is from 5% to 14% under nominal.

ON On Off Set Off AVR- Max. buck 11% of input voltage for output regulation while input

voltage is from 8% to 25% over nominal.

Off Off On Set Two Beeps Utility Failure- The UPS is providing battery power to the Battery-Powe

Supplied outlets.

Off Off On Set Rapid Beeps Utility Failure- The UPS is providing battery power. Rapid beeps

indicate the battery will run out of charge within a few minutes.

On/Off On/ Off

/Flash On/Off Set Long Beep

Overload- Turn the UPS off and unplug at least one piece of equipment

from the UPS. Wait 5 seconds, reset the circuit breaker and restart the

UPS.

Off Off On Up Long Beep

Overload- Turn the UPS off and unplug at least one piece of equipment

from the UPS. Wait 5 seconds, reset the circuit breaker and restart the

UPS.

Off Off Off Set Off Surge Protection Malfunction- Power surge has damaged the unit.

Please contact CyberPower Systems.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	OP1500
Bredde:	177.8 mm
Dybde:	419.1 mm
Højde:	241.3 mm
Vægt:	25401.1 g
Produktfarve:	Sort
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Tower
Relativ luftfugtighed ved drift (H-H):	0 - 95 %
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	1
Driftstemperatur (T-T):	0 - 35 °C
Udgangseffekt:	950 W
Certificering:	UL1778, cUL, FCC DOC Class B, ROHS
LED-indikatorer:	Ja
Kabellængde:	3 m
Batteritype:	BB 12V/7.0AH
Opladningstid for batteri:	8 t
Medfølgende software:	PowerPanel Plus
Kompatible operativsystemer:	Windows 200x, Server, XP, Vista, Windows 7.
Indgangsfrekvens:	60 Hz
Lydalarmer:	Ja
Input forbindertype:	NEMA 5-15P
Antal serielle porte:	2
Nominel udgangsspænding:	120 V
Output-forbindere:	6 x NEMA 5-15R
Administrationsplatform:	SNMP, HTTP
Modem-porte (RJ-11):	1
Overspænding energivurdering:	1796 J
Output strømkapacitet (VA):	1.5 kVA
Beskyttelse ved overspænding:	Ja
Typisk backup tid ved halv styrke:	18 min.
Typisk backup tid ved fuld styrke:	6 min.
EMI/RFI støjfiltrering:	Ja