CyberPower UT650E Manual

CyberPower Uafbrydelig strømforsyning (UPS) UT650E

Læs gratis den danske manual til CyberPower UT650E (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om CyberPower UT650E, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

UT650E User’s Manual K01-C000347-00

IMPORTANT SAFETY INSTRUCTIONS

This manual contains important safety instructions. Please read and follow all instructions carefully during installation and operation of the unit. Read this

manual thoroughly before attempting to unpack, install, or operate your UPS.

CAUTION! To prevent the risk of fire or electric shock, install in a temperature and humidity controlled indoor area free of conductive contaminants. (See the

specifications for the acceptable temperature and humidity range.)

CAUTION! To reduce the risk of overheating the UPS, do not cover the UPS' cooling vents and avoid exposing the unit to direct sunlight or installing the unit

near heat emitting appliances such as space heaters or furnaces.

CAUTION! Do not attach non-computer-related items, such as medical equipment, life-support equipment, microwave ovens, or vacuum cleaners to UPS.

CAUTION! Do not allow liquids or any foreign object to enter the UPS. Do not place beverages or any other liquid-containing vessels on or near the unit.

CAUTION! In the event of an emergency, press the OFF button and disconnect the power cord from the AC power supply to properly disable the UPS.

CAUTION! Unplug the UPS prior to cleaning and do not use liquid or spray detergent.

CAUTION! Servicing of batteries should be performed or supervised by personnel knowledgeable of batteries and the required precautions. Keep

unauthorized personnel away from batteries.

UNPACKING

The box should contain the following: (1) UPS Unit x1; (2) User Manual x1; (3) USB Cable x1

HARDWARE INSTALLATION GUIDE

1. Your new UPS may be used immediately upon receipt. However, recharging the battery for at least 8 hours is recommended to ensure that the battery's

maximum charge capacity is achieved. Charge loss may occur during shipping and storage. To recharge the battery, simply leave the unit plugged into

an AC outlet. The unit will charge in both the on and off position.

2. With the UPS unit off and unplugged, connect the computer, monitor, and any externally powered data storage device (Zip drive, Jazz drive, Tape drive,

etc. into the battery power supplied outlets. DO NOT plug a laser printer, copier, space heater, vacuum, paper shredder or other large electrical device

into the battery power supplied outlets. The power demands of these devices will overload and possibly damage the unit.

3. Plug the UPS into a 2 pole, 3 wire grounded receptacle (wall outlet). Make sure the wall branch outlet is protected by a fuse or circuit breaker and does

not service equipment with large electrical demands (e.g. air conditioner, refrigerator, copier, etc. Avoid using extension cords.

4. Press the power switch to turn the unit on. The power on indicator light will illuminate and the unit will "beep".

5. If an overload is detected, an audible alarm will sound and the unit will emit one long beep. To correct this, turn the UPS off and unplug at least one piece

of equipment from the battery power supplied outlets. Wait 10 seconds. Make sure the circuit breaker / fuse is normal and then turns the UPS on.

6. To maintain optimal battery charge, leave the UPS plugged into an AC outlet at all times.

7. To store your UPS for an extended period, cover it and store with the battery fully charged. Recharge the battery every three months to ensure battery

life.

1. Power Switch

Press the switch for 2 seconds to turn the UPS ON or OFF.

Alarm setting: The audible alarm can be turned OFF or ON by quickly pressing the POWER button twice. The default setting is for the Alarm

On. To turn the Alarm Off, quickly press the power button twice. You will hear two short beeps

when the Alarm is turned off. To turn the Alarm back on, quickly press the power button twice.

You will hear a single short beep when the Alarm is turned on.

2. Led Indicators This LED is illuminated when the UPS is working.

3. Input Power Cord Connect to utility power.

4. AC outlet

The UPS provides outlets for connected equipment to insure temporary uninterrupted

operation during a power failure and against surges and spikes.

5. USB Port

This port allows connection and communication from the USB port on the computer to the

UPS unit. The UPS communicates its status to the PowerPanel® Personal Edition software.

DEFINITIONS FOR ILLUMINATED LED INDICATORS

LED Alarm Condition

On Off Normal

Flash Beep Twice Utility Failure - The UPS is providing battery power to outlets.

Flash Rapid Beeping Utility Failure - The UPS is providing battery power. The rapid beeps indicate the battery will run out of power shortly.

On/Flash Constant Tone Overload - Occurs when connected equipment exceeds the rating of the unit. Turn the UPS off and unplug at least one

piece of equipment from the UPS.

BASIC OPERATION

INSTALLING YOUR UPS SYSTEM

TECHNICAL SPECIFICATIONS

TROUBLE SHOOTING

Problem Possible Cause Solution

The UPS does not perform

expected runtime.

Batteries are not fully charged. Recharge the battery by leaving the UPS plugged in.

Battery is slightly worn out. Contact CyberPower Systems Technical Support.

The UPS will not turn on.

The unit is not connected to an AC

outlet. The unit must be connected to a 220-240V outlet.

The battery is worn out. Contact CyberPower Systems Technical Support.

Mechanical problem. Contact CyberPower Systems Technical Support.

Outlets do not provide

power to equipment

Fuse is blown or breaker is tripped

due to overload.

Turn the UPS off and unplug at least one piece connected equipment. Unplug

the power cord of the UPS then replace the blown fuse with a spare one or press

the circuit breaker knob. Connect power cord then turn the UPS on. Make sure

that your spare fuse meets the specification.

Batteries are discharged Allow the unit to recharge for at least 4 hours.

Unit has been damaged by a surge

or spike. Contact CyberPower Systems Technical Support.

For more information, visit www.cyberpower.com

Model UT650E-AS

Capacity (VA/W) 650/360

Input

Voltage Range 165~290Vac

Nominal Frequency 50 Hz

Output

On Battery Output Voltage 220–240Vac

On Battery Output

Frequency 50 Hz +/-1%

Overload Protection Fuse

Physical

Total # of UPS

Receptacles 3

Dimensions (W x H x

D)(mm) 84x159x252

Weight 3.7 kg

Battery

Sealed Maintenance Free

Lead Acid Battery RBP0119 p2-x1

Typical Recharge Time 8 Hours

Warning Diagnostics

Indicators Power On / Using Battery

Audible Alarms On Battery, Low Battery, Overload, Fault

Environmental

Operating Temperature 0C to 40C

Operating Relative

Humidity 0 to 90%

Management

Auto-Charger Yes

Auto-Restart Yes

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	UT650E
Bredde:	84 mm
Dybde:	252 mm
Højde:	159 mm
Vægt:	3800 g
Produktfarve:	Sort
Batterispænding:	12 V
Batterikapacitet:	4.5 At
Formfaktor:	Mini Tower
Ethernet LAN-porte (RJ-45):	1
Udgangseffekt:	360 W
LED-indikatorer:	Ja
Opladningstid for batteri:	8 t
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
Effektivitet:	95 %
Modem-porte (RJ-11):	1
AC udgange, antal:	2 AC stikkontakt(er)
Indgående driftsspænding (maks.):	290 V
Output strømkapacitet (VA):	0.65 kVA
Indgående driftsspænding (min.):	165 V
Udgangs driftsspænding (min.):	- V
Udgangs driftsspænding (maks.):	230 V
UPS topologi:	Interaktivt indgangsstik
Bølgeform:	Sine
Hørbare alarmtilstande:	Alarm when on battery, Low battery alarm, Overload alarm
Automatisk batteritest:	Ja
Automatisk genstart:	Ja
Automatisk spændingsregulering (AVR):	Ja
Uddgående frekvens:	50/60 Hz