CyberPower VALUE2200E-GP Manual

CyberPower Uafbrydelig strømforsyning (UPS) VALUE2200E-GP

Læs gratis den danske manual til CyberPower VALUE2200E-GP (2 sider) i kategorien Uafbrydelig strømforsyning (UPS). Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om CyberPower VALUE2200E-GP, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

1200E/1500E/2200E

User’s Manual

K01-0000032-01

SAFETY WARNINGS

(SAVE THESE INSTRUCTIONS)

This manual contains important safety instructions. Please read and follow all instructions carefully

during installation and operation of the unit. Read this manual thoroughly before attempting to unpack,

install, or operate your UPS.

This equipment can be operated by any individuals with no previous training.

The socket-outlet shall be installed near the equipment and easily accessible.

During the installation of this equipment it should be assured that the sum of the leakage currents of the

UPS and the connected loads does not exceed 3.5mA.

Attention, hazardous through electric shock. Also with disconnection of this unit from the mains,

hazardous voltage still may be accessible through supply from battery. The battery supply should be

therefore disconnected in the plus and minus pole at the quick connectors of the battery when

maintenance or service work inside the UPS is necessary.

Do not dispose of batteries in a fire, the battery may explode.

Do not open or mutilate the battery or batteries, released electrolyte is harmful to the skin and eyes.

INSTALLING YOUR UPS SYSTEM

UNPACKING

Inspect the UPS upon receipt. The box should contain the following:

UPS Unit¯1; IEC Power Cord¯1;USB Cable¯ ¯1;User Manual 1; Management software Disk¯1

HOW TO DETERMINE THE POWER REQUIREMENTS OF YOUR EQUIPMENT

1. Insure that the equipment plugged into the battery power-supplied outlets does not exceed the UPS

unit’s rated capacity (1200VA/720W for Value 1200E, 1500VA/900W for Value 1500E,

2200VA/1320W for Value 2200E). If rated unit capacities are exceeded, an overload condition may

occur and cause the UPS unit to shut down or the fuse blow.

2. If the power requirements of your equipment are listed in units other than Volt-Amps (VA), convert

Watts (W) or Amps (A) into VA by doing the calculations below. Note: The below equation only

calculates the maximum amount of VA that the equipment can use, not what is typically used by the

equipment at any one time. Users should expect usage requirements to be approximately 60% of

below value.

TO ESTIMATE POWER REQUIREMENTS

Watts (W) x 1.67 = VA or

Amps (A) x 230 =

2. Add the totals up for all pieces of equipment and multiply this total by 0.6 to calculate actual

requirements. There are many factors that can affect the amount of power that your computer system

will require. The total load that you will be placing on the battery-powered outlets should not exceed

80% of the unit’s capacity.

HARDWARE INSTALLATION GUIDE

Before installation, please read and understand the following instructions:

1. Placement

The UPS must be installed in a protected environment away from heat- emitting appliances such

as a radiator or heat register. Do not install this product where excessive moisture is present.

2. Ventilation

The location should provide adequate air flow around the UPS with one inch minimum clearance

on all sides for proper ventilation.

3. Charge the Battery

Your new UPS may be used immediately upon receipt. However charge loss may occur during

shipping and storage. So charging the battery for at least 8 hours is recommended to insure that

the battery is fully charged. (To recharge the battery, simply leave the unit plugged into an AC

outlet.)

This UPS can be charged even when UPS is not turn on.

4. Connect to AC

Use German power cord to connect the UPS to a wall

outlet. Please avoid using extension cords and

adapter plugs. (To maintain optimal battery charge,

leave the UPS plugged in at all times.)

5. Connect the Load

Connect the equipment to your UPS outlets. The IEC

power cord coming with the unit are used to connect

your computer and monitor to the UPS. Items such

as copiers, laser printers, vacuums, space heaters,

or other large electrical devices SHOULD NOT be connected to the UPS. Please make sure

that the total loads of your equipments are less than the maximum total power load of your UPS.

6. Connect to Computer:

Install your software and accessories. To use the software, simply use the enclosed serial interface

or USB cable to connect the UPS unit and your computer.

BASIC OPERATION

FRONT PANEL DESCRIPTION

1. Power Switch

Press the power switch to turn the UPS ON or OFF.

2. LCD Function Selected Switch

The switch can be used to select the LCD display contents Including input/output voltage

and estimated run time, etc.

REAR PANEL DESCRIPTION

1. AC Inlet

Connect to utility power through the input power cord

2. Input Circuit Breaker

The circuit breaker provides optimal overload protection.

3. AC outlet

The UPS provides 6 outlets for connected equipment to insure temporary uninterrupted operation

during a power failure and against surges and spikes.

4. Serial Port to PC

This port allows connection and communicates

from the DB-9 serial on the computer to the

UPS unit. The UPS communicates its status to

the PowerPanel® Personal Edition software. This

interface is also compatible with the UPS service

provided by Windows 98, Windows ME,

Windows NT, Windows 2000, Windows XP,

Windows Server 2003, Windows Vista.

5. USB Port to PC

This port allows connection and communication

from the USB port on the computer to the UPS

unit. The UPS communicates its status to the

PowerPanel® Personal Edition software. This

interface is also compatible with the UPS service

provided by Windows 98, Windows ME,

Windows NT, Windows 2000, Windows XP,

Windows Server 2003, Windows Vista.

NOTE: Only one of these two ports

can be used as communication and

control of the UPS unit at one time.

6. Communication Protection Ports RJ11/RJ45

Communication protection ports will protect any standard modem, fax, telephone line, or network

cable.

Produkt Specifikationer

Mærke:	CyberPower
Kategori:	Uafbrydelig strømforsyning (UPS)
Model:	VALUE2200E-GP
Bredde:	140 mm
Dybde:	326 mm
Højde:	160 mm
Vægt:	15100 g
Produktfarve:	Sort
Skærmtype:	LCD
Batteriteknologi:	Blybatterier (VRLA)
Formfaktor:	Kompakt
Responstid:	4 ms
Ethernet LAN-porte (RJ-45):	1
Antal USB 2.0-porte:	1
Udgangseffekt:	1320 W
LED-indikatorer:	Power,Battery replacement
Opladningstid for batteri:	8 t
Medfølgende software:	PowerPanel Personal
Indgangsfrekvens:	50/60 Hz
Lydalarmer:	Ja
Strømbeskyttelsesfunktioner:	Overbelastning
Antal serielle porte:	1
Strømstik:	C14 forbinder
Modem-porte (RJ-11):	1
Beskyttelse mod overspænding:	Ja
AC udgange, antal:	6 AC stikkontakt(er)
Indgående driftsspænding (maks.):	265 V
Output strømkapacitet (VA):	2.2 kVA
Indgående driftsspænding (min.):	160 V
Udgangs driftsspænding (min.):	230 V
Udgangs driftsspænding (maks.):	230 V
Beskyttelsesfunktioner mod strømstød:	Fax,Modem,Network,Telephone
Beskyttelse ved overspænding:	Ja
Hørbare alarmtilstande:	Erstatningsbatteri
Typisk backup tid ved halv styrke:	7 min.
Typisk backup tid ved fuld styrke:	1 min.