Denver TRC-1460 Manual

Denver Vejrstationer TRC-1460

Læs gratis den danske manual til Denver TRC-1460 (32 sider) i kategorien Vejrstationer. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Denver TRC-1460, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/32

~P.1~

INDOOR & WIRELESS OUTDOOR THERMOMETER

WITH REAL TIME CLOCK & SNOOZE ALARM

MODEL: TRC-1460

INSTRUCTION MANUAL

1 . INTRODUCTION

Thank you for purchasing our In/Outdoor thermometer with wireless thermometer sensor and real time clock. The main unit

is designed to receive temperature signals from maximum 3 remote sensors in different locations, and it is also equipped with

a snooze alarm. To ensure proper operations, please read this instruction manual carefully and save it for future reference.

2 . DESCRIPTION OF BUTTONS

Main Unit

A . [SNOOZE/LIGHT] button

Activate the snooze function when an alarm sounds or turn on the backlight for 5 seconds.

B. [CLOCK] & [ALERT] button

Press the [CLOCK] side to display the real time clock, calendar or alarm time. When display the real time clock, press

and hold the [CLOCK] side for 2 seconds to activate the clock setting mode. When display the alarm time, press and

hold the [CLOCK] side for 2 seconds to enter the alarm setting mode.

Press the [ALERT] side to toggle to display high temperature alert and then low temperature alert for indoor thermom-

eter, channel 1, 2, 3 remote thermometers respectively and then return to normal thermo display mode.

Press & hold [ALERT] side for 2 seconds at the desired alert temperature display to enter its setting mode, use [+] / [-

] keys to change the settings, press [ALERT] again to confirm the setting or press no key for 10 seconds to auto-exit to

normal thermo display and confirm the setting.

C. [(°C/°F) MEM] button

Press the [(°C/°F)] side to select the temperature display in Celsius (°C) or Fahrenheit (°F).

Press the [MEM] side to toggle for max or min temperature memory reading for both IN & OUT thermometers. Press

ENG

~P.2~

and hold 2 seconds to clear both IN/OUT temperature memory.

D. [+] & [-] button

Press the [-] side to decrease the setting when enter setting mode of clock, alarm or temperature alert.

When display the alarm time, press [-] side to turn Daily Alarm on/oﬀ.

When display the temperature alert, press [-] side to turn the corresponding temperature alert on/off.

Press the [+] side to increase the setting when enter setting mode of clock, alarm or temperature alert.

E. [CHANNEL] button

Toggle to display remote thermo channel from channel 1, channel 2, channel 3 to Auto-scroll mode which alternately

display 3 channels;

Press and hold 2 seconds to activate searching mode for remote sensor;

Remote Sensor

The remote sensor has 3 function buttons inside the battery compartment.

a. [CH] button

After the battery installation, the LED blinks slowly every 1.5 seconds and channel number shows ‘1’ to indicate it is now

under channel setting mode and is set to channel 1 by default. If the user presses no key within ten seconds, the unit

will auto-exit the channel setting.

If the user press [CH] button once during the channel setting, the channel number is changed to ‘2’ to indicate the unit

is set to channel 2. If the user press [CH] button again, the channel number will be advanced to channel ‘3’ and so on.

b. [C/F] button (for sensor with LCD)

Press to toggle unit °C or °F

c. [RESET] button

Press to hardware reset the unit to factory setting

3. BATTERY INSTALLAT IO N

BATTERY INSTALLATION FOR MAIN UNIT

a. Remove the battery door;

b. Insert 2 pieces AAA size 1.5V alkaline battery as indicate by the polarity;

c. Close the battery door.

BATTERY INSTALLATION FOR REMOTE SENSOR UNIT

a. Lift off the bracket stand of the remote sensor unit by releasing the 2 fixing snaps at the bottom;

b. Use a small Philips type screwdriver to remove the battery cover screws;

c. Insert 2 pieces of AAA size batteries according to the “+” and “-” polarity marks shown in the battery compartment and

then close the battery door.

WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE

a. Insert p2-x2 AAA batteries first to the main unit. The temperature display shows ‘—.-C‘ while the wave icon will keep

blinking for 2 minutes indicate the main unit is in sensor searching mode.

b. In a second step, insert the p2-x2 AAA batteries into the sensor unit. The LED on the front panel will start ﬂashing at a rate

of one time per around 2 seconds indicates channel-1 is in use.

c. While the LED is flashing, press once the [CH] key will change the sensor channel setting to 2. Keep toggle on [CH] key

can change channel setting up to 3. The LED is blinking at a frequency to indicate the channel setting. i.e. continuous

blinks 2 times indicate channel-2 is selected.

4 . HOW TO SET TIME AND CALENDAR

a. Make sure the 1st line of the LCD displays the clock time, press & hold [CLOCK] button for 2 seconds to enter clock setting

mode. Flashing 24 hours will appear.

b. Press [ + ] or [ - ] button to switch between 24 hours and 12 hours format, and then press [CLOCK] button to conﬁrm.

c. The hour digits will flash. Use the [ + ] button to increase by one hour or [ - ] button to decrease by one hour to your

desired hours. Holding down either button will change the increment rapidly. Press [CLOCK] button to confirm.

d. The minute digits will flash. Use the [ + ] button or [ - ] button to set your desired minutes. Holding down either button

will change the increment rapidly. Press [CLOCK] button to confirm.

e. The year digit will flash and Yr icon appears. Press [ + ] or [ - ] button to set your desired year. Press [CLOCK] button to confirm.

f. D and M icons will flash. Press [ + ] or [ - ] to select D M (Date Month) or M D (Month Date) format. Press [CLOCK]

button to confirm.

Note: Never set the channel to ‘4’ & ‘5’ which would not be applied in this model

NOTE: Please insert batteries for the main unit first, then the RF remote sensor.

Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the RF signal.

The main unit will register the temperature reading.

Note: Every change of minute digit will automatically reset the seconds to zero.

Note: Year range is from 2000 to 2099.

ENG

Produkt Specifikationer

Mærke:	Denver
Kategori:	Vejrstationer
Model:	TRC-1460

Har du brug for hjælp?

Hvis du har brug for hjælp til Denver TRC-1460 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstationer Denver Manualer

Denver TRC-1480 Mk2 Manual

5 Oktober 2022

Denver TRC-1470 Manual

5 Oktober 2022

Denver WS-72 Manual

5 Oktober 2022

Denver TRC-1460 Manual

5 Oktober 2022

Denver TRC-1480 Manual

5 Oktober 2022

Vejrstationer Manualer

Nyeste Vejrstationer Manualer

AcuRite 02022WB Manual

15 Januar 2025

Hama EWS-1500 Manual

13 Januar 2025

Techno Line WS 6820 Manual

12 Januar 2025

Technoline WS 6740 Manual

13 Oktober 2024

AcuRite 02040 Manual

13 Oktober 2024

Alecto WS-2500 Manual

13 Oktober 2024

Prologue YT6981 Manual

12 Oktober 2024

Cotech E0336WST4H4PR Manual

12 Oktober 2024

Irox EBR808C Manual

10 Oktober 2024

Techno Line WS 6600 Manual

8 Oktober 2024