DeWalt DW902 Manual

DeWalt Lommelygte DW902

Læs gratis den danske manual til DeWalt DW902 (8 sider) i kategorien Lommelygte. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16 anmeldelser. Har du et spørgsmål om DeWalt DW902, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

If you have any questions, call 1-800-4-DEWALT (1-800-433-9258)

English

9.6, 12, 14.4, 18 Volt Heavy Duty

Flashlights

DW902 (9.6 V), DW904 (12 V), DW906 (14.4 V),

DW908 (18 V)

– Extra bulb stored in light behind

lens.

– Use with DEWALT power packs and

chargers (both sold separately).

IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS

OR ANY DeWALT TOOL, CALL US TOLL FREE AT:

1-800-4-DEWALT (1-800-433-9258)

NOTE: DEWALT heavy duty flashlights operate on the following

battery packs.

WARNING: When using electric tools, basic safety precautions

should always be followed to reduce risk of fire, electric shock,

and personal injury, including the following:

READ ALL INSTRUCTIONS

Safety Rules for Heavy Duty Flashlights

WARNING: DO NOT OPERATE FLASHLIGHT OR CHARGER

NEAR FLAMMABLE LIQUIDS OR IN GASEOUS OR

EXPLOSIVE ATMOSPHERES. INTERNAL SPARKS MAY

IGNITE FUMES.

WARNING: Lens and bulb become hot during use.

• During or immediately after use, don’t lay flashlight flat on lens

surface.

• Don’t touch lens surface when bulb is lit.

• Handle flashlight with care around any flammable surface.

• If bulb has been lit, let flashlight cool for several minutes

before changing bulb.

Safety Rules for Chargers

1. Before using charger, read all instructions and cautionary

markings on (1) charger, (2) battery pack, and (3) product

using battery pack.

2. DANGER: 120 volts present at charging terminals. Do not

probe with conductive objects. Danger of electric shock or

electrocution.

3. If battery pack case is cracked or damaged, do not insert into

charger. Danger of electric shock or electrocution.

4. The charger and battery pack are specifically designed to

work together. DO NOT attempt to charge the battery pack

with any chargers other than the ones in this manual.

5. Do not expose charger to rain or snow.

6. To reduce risk of damage to electric plug and cord, pull by

plug rather than cord when disconnecting charger.

7. Make sure cord is located so that it will not be stepped on,

tripped over, or otherwise subjected to damage or stress.

8. An extension cord should not be used unless absolutely

necessary. Use of improper extension cord could result in risk

of fire, electric shock, or electrocution.

9. Two wire cords can be used with 2 or 3 wire extension cords.

Only round jacketed extension cords should be used, and we

recommend that they be listed by Underwriters Laboratories

(U.L.) (C.S.A. in Canada.) The letters WA on the cord jacket

indicate that the cord is suitable for outdoor use.

10. An extension cord must have adequate wire size (AWG or

American Wire Gauge) for safety. The smaller the gauge

number of the wire, the greater the capacity of the cable, that

is 16 gauge has more capacity than 18 gauge. When using

more than one extension to make up the total length, be sure

each individual extension contains at least the minimum wire

size.

CHART FOR MINIMUM WIRE SIZE (AWG) OF EXTENSION CORDS

NAMEPLATE RATING AMPS - 0 - 10.0

Total Extension Cord Length (feet) 25 50 75 100 125 150 175

Wire Gauge 18 18 16 16 14 14 12

11. The charger is ventilated through slots in the top and the

bottom of the housing. Do not place any object on top of the

charger or place the charger on a soft surface that might block

the ventilation slots and result in excessive internal heat.

Place the charger in a position away from any heat source.

12. Do not operate charger with damaged cord or plug — have

them replaced immediately.

13. Do not operate charger if it has received a sharp blow, been

dropped, or otherwise damaged in any way; take it to an

authorized DeWalt service center.

14. Do not disassemble charger; take it to an authorized DeWalt

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock, electrocution

or fire.

15. To reduce risk of electric shock, unplug charger from outlet

before attempting any cleaning. Removing the battery pack

will not reduce this risk.

16. NEVER attempt to connect 2 chargers together.

17. DO NOT store or use the tool and battery pack in locations

where the temperature may reach or exceed 105°F (such as

outside sheds or metal buildings in summer).

18. The charger is designed to operate on standard household

electrical power (120 volts). Do not attempt to use it on any

other voltage!

Safety Rules for Batteries

1. Do not incinerate the battery pack even if it is severely

damaged or is completely worn out.The battery pack can

explode in a fire.

2. A small leakage of liquid from the battery pack cells may occur

under extreme usage or temperature conditions. This does

not indicate a failure. However, if the outer seal is broken and

this leakage gets on your skin:

a.Wash quickly with soap and water.

b.Neutralize with a mild acid such as lemon juice or

vinegar.

c.If battery liquid gets into your eyes, flush them with clean

water for a minimum of 10 minutes and seek immediate

medical attention. ( The liquid is 25-35%Medical note:

solution of potassium hydroxide.)

3. Never attempt to open the battery pack for any reason. If the

plastic housing of the battery pack breaks or cracks,

immediately discontinue use and do not recharge.

4. Do not carry extra battery packs in aprons, pockets, or tool

boxes along with other metal objects. Battery pack could be

short circuited causing damage to the battery pack and

possibly causing severe burn or fire.

NOTE: Battery storage and carrying caps are provided for use

whenever the battery is out of the tool or charger. Remove cap

before placing battery in charger or tool.

WARNING: Do not store or carry battery so that metal

objects can contact exposed battery terminals.

For example, do not place battery in aprons, pockets,

tool boxes, product kit boxes, drawers, etc. with loose

nails, screws, keys, etc. without battery cap. Without

cap in place, battery could short circuit causing fire or

burns or damage to battery.

SAVE THESE INSTRUCTIONS FOR

FUTURE USE

Charging Procedure

Chargers require no adjustment and are designed to be as easy

as possible to operate. Simply place your battery pack into the

receptacle of a plugged in charger and it will automatically charge

the pack.

15 MINUTE CHARGER

1. Plug the charger into an appropriate AC power outlet. The

charger will beep twice, the red light will blink and go off.

2. Insert the battery pack into the charger, making sure the pack

is fully seated in the charger. The red light will blink and the

charger will beep once indicating the charging process has

started.

3. The battery pack will be fully charged in less than 15 minutes

under most conditions. This will be indicated by the red light

remaining ON and 3 beeps. The pack is fully charged and may

be used at this time or left in the charger.

Weak Battery Packs: (DW9115). The charger can also detect a

weak battery. Such batteries are still usable but should not be

expected to perform as much work. In such cases, about 10

seconds after battery insertion, the charger will beep rapidly 8

times to indicate a weak battery condition. The charger will then

go on to charge the battery to the highest capacity possible.

ONE HOUR CHARGERS

1. Plug the charger into an appropriate AC power outlet.

2. Insert the battery pack into the charger, making sure the pack

is fully seated in the charger. The red (charging) light will blink

continuously indicating that the charging process has started.

3. The completion of charge will be indicated by the red light

remaining ON continuously. The pack is fully charged and may

be used at this time or left in the charger.

Leaving the battery pack in the charger: When the red light

remains ON, the charger has switched to its "equalize charge"

mode which lasts approximately 4 hours, after which the charger

will switch to "maintenance charge" mode. The battery pack can

be removed at any time during these charge cycles, but will only

be fully charged if the red light is continuously ON. The charger

and battery pack can be left connected with the red light glowing

indefinitely. The charger will keep the battery pack fresh and fully

charged. A battery pack will slowly lose its charge when kept out

of the charger. If the battery pack has not been kept on

maintenance charge, it may need to be recharged before use. A

battery pack may also slowly lose its charge if left in a charger

that is not plugged into an appropriate AC source.

Trouble Indicators: These chargers are designed to detect

certain problems that can arise with battery packs which would be

indicated by the red light flashing at a fast rate (and continuous

beeping for DW9115, DW9107, DW9108). If this occurs, re-insert

battery pack. If problem persists, try a different battery pack to

determine if the charger is OK. If the new pack charges correctly,

then the original pack is defective and should be returned to a

service center for recycling. If the new battery pack elicits the

same trouble indication as the original, have charger tested at an

authorized service center.

PROBLEM POWER LINE (DW9107)

When these chargers are used with some portable power sources

such as generators or sources that convert DC to AC, the

chargers may temporarily suspend operation, flashing the red

light with two fast blinks followed by a pause. This indicates

the power source is out of limits.

Battery Insertion and Removal

To insert the power pack into your flashlight, slide it into the end of

the light until it snaps into place. To remove the power pack,

depress the release buttons shown and withdraw the power pack.

If you have any questions, call 1-800-4-DEWALT (1-800-433-9258)

FIG. 1

FIG. 3

LENS HOLDER

PORTE-LENTILLE

SUJETADOR DE LA LENTE

BULB

AMPOULE

BOMBILLA

BATTERY RELEASE BUTTON

BOUTON DE DÉGAGEMENT DE LA PILE

BOTON DE LIBERACION DE LA BATERIA

SPARE BULB STORAGE

RANGEMENT DE L’AMPOULE DE RECHANGE

COMPARTIMIENTO PARA BOMBILLA DE REPUESTO

POWER PACK (NOT INCLUDED)

ENSEMBLE DE PILES

(NON COMPRIS)

BATERIA (NO INCLUIDA)

PIVOTING HEAD

TÊTE PIVOTANTE

CABEZA GIRATORIA

SWITCH

INTERRUPTEUR

INTERRUPTOR

FIG. 2

Produkt Specifikationer

Mærke:	DeWalt
Kategori:	Lommelygte
Model:	DW902

Har du brug for hjælp?

Hvis du har brug for hjælp til DeWalt DW902 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Lommelygte DeWalt Manualer

9 Juni 2025

22 September 2024

3 September 2024

7 August 2024

29 Juli 2024

23 Juli 2024

20 Juli 2024

18 Juli 2024

3 August 2023

5 November 2022

Lommelygte Manualer

Nyeste Lommelygte Manualer

PNI Adventure F750 Manual

16 Juni 2025

PNI Adventure F550 Manual

15 Juni 2025

PowerSmith PHL15F Manual

14 Juni 2025

PowerSmith PHL23FRGS Manual

14 Juni 2025

PNI Adventure F650 Manual

9 Juni 2025

NightStick USB-558XL Manual

9 Juni 2025

PNI Adventure F420 Manual

8 Juni 2025

Ledlenser P4 Manual

1 Juni 2025

Draper 70299 Manual

31 Maj 2025

NEO Tools 99-130 Manual

30 Maj 2025