Draper Access FIT V Manual

Draper Projektionsskærm Access FIT V

Læs gratis den danske manual til Draper Access FIT V (8 sider) i kategorien Projektionsskærm. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Draper Access FIT V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

Contents

Overview - Components .......................................................................................1

Section 1 - Removing Shipping Brackets

(Tab-Tensioned, "V" Surfaces only)

.......2

PLEASE READ - Safety Information ....................................................................2

Section 2 - Hanging Screen .................................................................................3

Section 3 - Bottom Access FIT Panel Installation/Removal ..........................3

Section 4 - Motorized Roller/Fabric Installation ..............................................4

Section 5 - Motorized Roller/Fabric Removal ...................................................4

Section 6 - Operation............................................................................................5

Section 7 - Tab-Tension Adjustment Procedure ..............................................5

Section 8 - Limit Adjustments .............................................................................6

Section 9 - Case Length Dimensions ................................................................. 7

Section 10 - Case Width Dimensions .................................................................7

Section 11 - Mounting Bracket Dimensions......................................................7

Section 10 - Wiring Diagrams: 110-120V Motor and Quiet Motor ..................8

Overview - Components

CAUTION

Read and understand all warnings

(Page 2)

before beginning installation.

Electrical

Cutout

Tab Tensioning

“V” Dowel

“E” Dowel

Mounting Bracket

Mounting Bracket Hoisting Bracket

Leveling Brackets

Hoisting Bracket

“E” Free Hanging

Viewing Surface

“V” Flexible Vinyl

Viewing Surface

Trim Flange

Shipping Brackets Attached

to Dowel and Screen Case

(V Screens Only)

Please Note: Shipping brackets must remain

in place until product has been mounted and

connected to power

(see Sections 1 and 4 in this

document.)

Also, DO NOT operate screen before removing

shipping brackets from screen case.

TOOLS REQUIRED

POW R RILE D L

PENCIL

TAP ASUE E M RE

HAR ARDW E

(b oth rs)y e

L LEVE

Draper, Inc. | 411 S. Pearl St. Spiceland, IN 47385

draperinc.com | 765.987.7999 | 800.238.7999

Access FIT E and V

Electric projection screen

INSTRUCTIONS

INSTALLATION & OPERATION

If you have any difﬁculties installing or servicing your

Access FIT screen, call your dealer or Draper, Inc.

PLEASE READ - Safety Information

WARNING

Improper installation and use of the Access Fit E and V screen can result in serious injury or death. Primarily, injuries can occur if the unit falls due to

imprecise installation, mishandling of the unit during installation, or installation on an insufﬁcient wall or ceiling structure. Please use extreme care.

Please read the following installation guidelines thoroughly and follow them

carefully. Failure to do so may cause product to fall or otherwise fail, and could

result in serious injury.

Installation and calibration of the unit should only be performed by an

authorized, qualiﬁed, and experienced professional. In particular, electrical

work and wiring [indicated in diagram by dashed lines] must be completed only

by a qualiﬁed professional electrician who has read this manual completely

and is familiar with the construction and operation of this equipment and the

hazards involved.

Do not afﬁx the unit to walls or ceilings that have inadequate strength

to permanently hold the unit during use. It is the owner’s and installer’s

responsibility to conﬁrm the wall or ceiling to which the unit attaches is

sufﬁcient to permanently hold the weight and stress loads of the unit at all

times. Draper, Inc., is not responsible for improper installation, application,

testing, or workmanship related to the product at place of installation.

It is the installer’s responsibility to make sure appropriate fasteners are used

for mounting.

All hardware must be installed level. Unit must be level and square.

Never leave the area while operating the unit during installation, maintenance,

or normal operation, unless it is secure and safe.

Before testing or operation, carefully inspect the entire area and path

(especially

underneath)

of unit to be sure no persons or objects are in the area.

Turn off power and any nearby equipment or cables carrying electricity before

connecting switches, wires, controls, or electrical components.

Do not wire motors in parallel without written permission from Draper, Inc.

10.

During testing or operation, carefully watch the surrounding area for any

potential safety concerns including nearby persons or objects.

11.

After installation, the entire system, including all sensors, should be carefully

tested to ensure safe and normal operation. Extreme care should be taken

during testing to remain clear of moving parts to avoid possible injury.

12.

Operation of unit should be performed only by authorized and qualiﬁed

personnel, who have been trained in its safe and effective operation and

understand its safety features.

13.

The safety features of the unit should never be disabled, bypassed, or

overridden. The system should not be operated until all safety features are

properly and completely installed, calibrated, and tested.

14.

Unit may need to comply with local, state, or district rules and regulations, in

particular when installed in schools. All applicable rules and regulations should

be reviewed before installation and use.

15.

Failure to precisely follow installation guidelines invalidates all

warranties.

16.

Custom products/installations may not be reﬂected in this manual. Call Draper,

Inc., if you have questions about the installation of custom products or any

questions about your installation.

Before Beginning Installation

Look for any job site conditions that could interfere with installation or

operation of the system.

Read carefully and be sure to understand all installation instructions and

all related operations manuals. These instructions are intended to serve

as a guide for the installer and owner. They should be followed closely and

combined with the expertise of experienced qualiﬁed installers. Draper, Inc., is

not responsible for improper installation, application, testing, or workmanship

related to the product at place of installation. Please retain all instructions for

future use.

Open cartons lengthwise.

Locate and lay out all pieces.

Inspect all boxes to make sure you have received the proper unit and parts.

Controls may be shipped separately, or in same carton as unit.

If you have any difﬁculties with installing, servicing, or operating your unit, call

your dealer or Draper, Inc., 765-987-7999.

Important Safety Information Important Safety Information

Remove

fasteners from

bracket clamps.

Run screen

DOWN to expose

dowel screws.

Loosen screws

and remove

shipping bracket.

Retighten

dowel endcap

screws.

Section 1 - Removing Shipping Brackets

(Tab-Tensioned, "V" Surfaces only)

CAUTION: DO NOT remove shipping

brackets until product has been

mounted and connected to power

(see

Section 4 in this document.)

Also, DO NOT OPERATE SCREEN

BEFORE REMOVING SHIPPING

BRACKETS FROM SCREEN CASE.

page 2 of 8

Access FIT E and V

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionsskærm
Model:	Access FIT V
Vægt:	34000 g
Produktfarve:	Hvid
Pakkevægt:	41000 g
Naturligt aspektforhold:	16:9
Monteringstype:	Loft
Skærmoverflade:	Mat hvid
Drevtype:	Motoriseret
Synlig skærmbredde (W):	2030 mm
Synlig skærmhøjde (H):	1140 mm
Diagonal:	92 "
Format:	HDTV
Sort fald:	305 mm
Boks L1:	2720 mm
Farve på etui:	Hvid
Spændt skærm:	Ja