Draper Onyx Manual

Draper Projektionsskærm Onyx

Læs gratis den danske manual til Draper Onyx (3 sider) i kategorien Projektionsskærm. Denne vejledning er vurderet som hjælpsom af 59 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 30 anmeldelser. Har du et spørgsmål om Draper Onyx, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Assembly/Mounting Instructions

Onyx Permanently Tensioned Projection Screen by Draper

Caution

1 Read instructions through completely before proceeding.

2 Follow instructions carefully. Installation contrary to instructions

invalidates warranty.

3 Screen should be accessible for complete removal should fabric

become damaged or should other service be required.

4 Screen should be installed level (using a carpenter’s level).

5 Nothing should be fastened to screen frame or viewing surface.

6 Make sure you have received all parts (see parts list below and

exploded diagram on page 2).

7 Tools Required:

" Allen wrench (included); #2 Phillips screwdriver.

Optional tools: Flat blade screwdriver or small putty knife.

8 Installer is responsible for providing appropriate hardware for mounting.

9 When lifting assembled screen, do not lift at only one corner; lift at

both corners. Lifting by one corner could result in damage to the

screen frame, especially on large screens.

 The ideal temperature range for assembling folding screens to prevent

damaging the surface is 68°-78° F (20°-26° C). Assembling below

recommended temperatures may damage surface and void warranty.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

If you encounter any difﬁculties installing or servicing your Onyx screen, call your

dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

Onyx—Hardware and Parts List

Frame Preparation

1 Clean area and place frame assembly pieces face down. Insert corner

brackets into aluminum frame extrusions as indicated in Figures 1 through

4. For easier assembly insert the inner connectors ﬁrst.

Figure 1

2 Make sure corner brackets are fully seated (see Fig. 5).

Figure 3

Frame Extrusions - 4

Wall-Bra ets - 2 Viewing Surface - 1ck

Plastic Tubing - 4

Surface Retention Extrusions

Typically 4, ries with va

some veiwing surfaces

Front

Back

1/ " Allen Wrench - 18

Corner Brackets - 8

Figure 4

Figure 7

Figure 5

(Continued on Page 2)

Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310.

Caution: When lifting assembled screen, do not lift at only one corner; lift

at both corners. Lifting by one corner could result in damage to the screen

frame, especially on large screens.

Figure 2

3 Secure corner brackets by tightening setscrews (see Fig. 6).

Figure 6

4 Repeat steps 1-3 for the remaining corners (see Fig. 7).

The Onyx has a precision cut mitered corner.

Please Note: If corner gaps exist (painted frame only) readjusting the frame

and/or applying a small bead of black silicone to ﬁll the gap is the best solu-

tion. Apply a very small bead of black silicone to area where frame gap exists.

Work silicone into gap (using your ﬁnger or a cloth). Remove ALL silicone on

face of frame; only silicone inside gap should remain.

Please Note: If corner brackets do not slide into frame extrusions, make sure

that setscrews are backed out enough to allow proper clearance.

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionsskærm
Model:	Onyx
Vægt:	13000 g
Produktfarve:	Hvid
Naturligt aspektforhold:	4:3
Monteringstype:	Væg
Betragtningsvinkel:	100 °
Synlig skærmbredde (W):	1600 mm
Synlig skærmhøjde (H):	1190 mm
Samlet skærmstørrelse (højde x bredde):	127 x 168 cm
Diagonal:	78 "
Skærmforstærkning:	1.5