Draper Silhouette V Manual

Draper Projektionslærred Silhouette V

Læs gratis den danske manual til Draper Silhouette V (5 sider) i kategorien Projektionslærred. Denne vejledning er vurderet som hjælpsom af 39 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 20 anmeldelser. Har du et spørgsmål om Draper Silhouette V, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

Silhouette fully engaged

on "Z" Clip

Ceiling bracket

Mounting fasteners

(supplied by others, 2 per bracket)

(front of Silhouette case)

(right end of Silhouette case)

Installation/Operating Instructions

Silhouette/Series E & V Electric Projection Screen by Draper

Installation

Your Draper screen can be mounted on a wall or suspended from the ceiling,

or mounted on 6" or 10"-14" extension brackets. Extension brackets must be

ordered separately from Draper. With each method of installation, the case

must be mounted level and with the ﬂat back parallel to the wall.

To reduce the risk of personal injury, use only the hardware which comes with

the screen or is speciﬁed in these instructions.

The screen (or wall extension brackets) should be mounted into studs or

blocking in the wall/ceiling, or in drywall (minimum thickness

") with speci-

ﬁed anchors. For any other type of installation, follow all local building and

safety codes.

Steel studs, concrete or cinder block walls and all other types of non-wood

frame construction require the use of special screws or anchors. The selection

of appropriate mounting hardware should be made by a qualiﬁed professional

installer.

When locating viewing surface and checking clearance for screen’s operation,

remember surface is centered in case.

Take care to install wall/ceiling electrical box and conduit so they will be fully

concealed by the screen case after installation.

Handle case carefully to avoid scratching.

Regardless of mounting method, screen should be positively and securely

supported so that vibration or even abusive pulling on the viewing surface will

not cause case to work loose or fall. Installer must insure that fasteners used

are of adequate strength and suitable for the mounting surface chosen.

Ceiling/Suspended Mounting

Locate two offset ceiling brackets (supplied) and slide these into the chan-

nel on top of screen case by aligning the chamfered edges of each bracket

parallel to the channel length. Allow bracket to drop against bottom of channel

and then rotate bracket counter-clockwise. Slide one bracket to each end of

screen case until it stops against end cap of case. Tighten two set screws

to lock bracket in place. Make sure that the ﬂange of the ceiling bracket that

has four holes is extended beyond the end caps of the case. Repeat above

procedure for second ceiling bracket, making sure to slide it towards opposite

end of case.

Wall Mounting

Mount two, three or four aluminum brackets provided (“Z” Clips) on the wall

at desired height, using appropriate fasteners. Verify that they are in line and

level to fully engage with the mounting lip on back of screen case. 1

" of free

space is required above the “Z” Clips to allow case lip to be engaged over the

lip of the “Z” Clips.

Engage the lip on back of screen case with lip of “Z” Clip and gently pull down

to fully engage case to brackets.

These instructions are meant as a guide only. They do not imply any

responsibility on the part of Draper, Inc. for improper installation or faulty

workmanship at the jobsite.

Caution

1 Read instructions through completely before proceeding; keep them for

future reference. Follow instructions carefully. Installation contrary to

instructions invalidates warranty. Care in mounting and correct oper-

ation will mean long and satisfactory service from your Draper screen.

2 Screen should be accessible for complete removal should fabric

become damaged or should other service be required.

3 Screen should be installed level (using a carpenter’s level).

4 Nothing should be fastened to screen dowel or viewing surface

5 Operating switch(es) packed separately in screen carton. Do not

discard with packing material.

6 Screen operates on 110-120V, 60 hz., 1.1 amp current draw.

NOTE: Screen has been thoroughly inspected and tested at factory and

found to be operating properly prior to shipment.

Lip on back of case

"Z" Clip

(wall mounting bracket

supplied with Silhouette)

Ceiling bracket in

channel of case

To mount against ceiling, hold screen case against ceiling and mark mount-

ing hole locations. Each bracket has two holes towards the front edge and

two holes towards the back edge. Installer must use at least two fasteners

per bracket with one fastener in one of the two holes closest to back edge

of bracket, and one fastener in one of the two hole closest to front edge of

bracket. Installer must insure that fasteners are of adequate strength and suit-

able for the mounting surface chosen.

If you encounter any difﬁculties installing or servicing your screen, call your dealer

or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142.

To mount suspended from ceiling, the brackets need to be installed on

screen case as noted on page 1. Use “S” Hooks through the holes in the

brackets to attach to ceiling. Select the set of holes that allows the screen to

hang in a vertical position. The installer is to provide the "S" Hooks and the

materials and fasteners to attach the “S” Hooks to the ceiling. Installer must

insure that the fasteners and suspension material is of adequate strength and

suitable for the mounting surface chosen.

US Patent Nos. 5,296,964; 6,111,694

Silhouette/Series E & V by Draper

Page 2 of 5

Removing Case Fascia

Caution: When removing or reattaching fascia, do not handle fascia

by unpainted ends.

Case fascia is removable to access roller assembly. To remove fascia, depress

outward the spring lip located inside lower front corner of screen case and

pull lower corner of fascia outward. Repeat this at right end of case. Support

fascia from center and rotate lower front edge upward approximately 40° to

disengage the Roll-Lok hinge at the top front of screen case. Fascia can now

be completely removed from case.

To install fascia, generally reverse instructions above making sure the Roll-

Lok hinge is completely engaged before rotating fascia down towards the

closed position. Depress spring clips outward, push lower corners of fascia

inward until lips of spring clips hook behind fascia.

Please Note: Be sure the clips are completely up against the ends of the

fascia.

Electrical Connections

Screen operates on 110-120V, 60 Hz., 1.1 amp current draw. Duty Cycle: ON

28 seconds/OFF 4 minutes.

Junction box is located at left end of screen. It is accessible through front

of screen case after fascia is removed (see instructions above for removing

fascia).

Electrical supply wires can enter through the back or top of case. For top

entry, remove plug from top conduit hole and snap plug into hole on back side

of case.

Junction box contains red, black, and white pigtail leads and green internal

ground wire per wiring diagram attached.

If optional low voltage control or video interface control is speciﬁed, please

refer to wiring diagrams on pages 4-5.

Wall or ceiling electrical box should be installed so as to be fully concealed by

screen case after installation.

Screen is shipped with internal wiring complete and control switch(es) fully

boxed. Wire to connect screen to switch(es) and switch(es) to power supply

should be furnished by installer. Please Note: Screen must be installed in

accordance with the requirements of the Local Building Codes, the Cana-

dian Electrical Code (CEC), CAN/CSA C22.1 and the National Electric Code

(NEC), NFPA 70. An appropriate disconnect device shall be provided as part

of the building installation.

All operating switches should be “off” before power is connected.

Plug-in power cord option available on units with built-in low voltage controller.

For Reconﬁguration/Conversion of Non-detachable Power Cord to

Field Wiring for Models SLE-28, SLE-30, SLV-28 and SLV-30 Only:

1 Disconnect cord plug from outlet.

2 Remove junction box cover.

3 Disconnect wire nut connections from black, white and green wires.

4 Remove power cord and strain relief.

5 Connect the black from motor to "hot" supply wire.

6 Connect white wire from motor to "neutral" supply wire.

7 Connect green/yellow ground to "ground" supply wire.

8 Replace junction box cover.

Operation

Before operating screen, remove any shipping brackets or tape securing fab-

ric and dowel to the roller. If viewing surface hangs out of case 8" or 9", tape

has probably been broken by rough handling in shipment, allowing surface to

“unwrap” one turn off the roller. Manually wrap fabric back around the roller

without turning the roller itself.

When screen is ﬁrst operated, Cycle unit down and up several be cautious!

times to conﬁrm satisfactory operation.

110-120V SINGLE STATION CONTROL—3-position UP-OFF-DOWN switch

permits operation to be stopped at any point. Factory adjusted limit switches

automatically stop screen when fully down or fully up.

110-120V MULTIPLE STATION CONTROL—Switches are similar in ap-

pearance to 110-120V Single Station Control. Screen stops when switch

is released and may be restarted in either direction. Factory adjusted limit

switches stop screen automatically when fully down or fully up.

24V MULTIPLE STATION CONTROL—Three-button UP-STOP-DOWN

switches stop at any point desired, operate in any sequence. Factory adjusted

limit switches automatically stop screen when fully down or fully up.

110-120V & 12V VIDEO INTERFACE CONTROL—Allows screen to be con-

trolled by a trigger signal—when the signal comes on, the screen descends

automatically. Two versions: Model VIC115 integrates screen operation with

a DRAPER video projector lift or a video projector or tuner with a 110-120V

switch outlet. Model VIC12 interfaces with a 12V switch outlet. Both available

with an override switch (VIC–OS), permitting independent operation. VIC–OS

not available with factory installed VIC115 & VIC12.

KEY OPERATED SWITCHING—Two kinds of key-operated switches are

optionally available with this unit.

1 The key-operated power supply switch controls power to the screen and

switches. When it is “off”, the switches will not operate screen.

Key may be removed from the switch in either “on” or “off” position.

2 A three-position key switch permits the screen to be operated directly by

key. In this case, the screen’s operator must always have a key.

RS232/ETHERNET—Serial communication and network communication

optionally available with wall switches, RF or IR remote.

PLUG & PLAY

—Provided with handheld IR remote control transmitter and

10' (3m) cord. No wiring necessary except to connect to RS232. Screen is

equipped with a handheld remote or 3-position operating switch (see below).

Three positions (up-off-down) permit operation to be stopped at any point.

Factory adjusted limit switches automatically stop screen when fully down or

fully up.

Limit Adjustments—Standard Motor

Please Note: Screen limits are factory set for optimum performance of

the screen. A procedure is outlined below for minor tweaks, but any ad-

justment of these limits may negatively affect the ﬂatness of the screen

surface and could also void the warranty. Please check with Draper prior

to resetting screen limits.

CAUTION: Always be prepared to shut screen off manually when new

adjustment is being tested. Screen may be severely damaged if viewing

surface is allowed to run too far up or too far down.

CAUTION: Be sure all switches are in “off” position before adjusting

limit switches.

The motor limit screws are normally located on the audience left of screen

roller.

www

.draperinc.com (765) 987-799

Extension Wall Brackets

6" or 10"-14" Extension Wall Brackets are needed to mount Silhouette

extended from wall. Wall Brackets are not supplied with screen and must be

ordered separately. Specify “Silhouette Extension Wall Brackets”.

1 Mount the Wall Brackets to the wall, making sure they are level and verti-

cally plumb. Installer must insure fasteners (not included) are of adequate

strength and suitable for chosen mounting surface.

2 Attach hanging bracket to wall bracket as shown.

3 Attach (1) “Z” Clip and (1) Support Plate (supplied with screen) to hanging

bracket as shown.

4 Engage the lip on back of screen case with lip of “Z” Clip and gently pull

down to fully engage case to brackets.

5 Install hook bracket as shown making sure the two tabs of this bracket

hook over the case extrusion.

6 Install #10-24 hex head screw through hook bracket, hanging bracket, and

support plate as shown.

Hook

Bra tcke

CB ¼"-20 x 1¾" Z Keg,

Flat Washer,

¼"-20 Nylock Nut

#10-24 x

Phillips Pan Head

Scre Nylock Nutw,

#10-24 x ½"

Hex Head Screw

Z Clip

Wall

Bra tcke

Support

Plate

Hanging

Bra tcke

Produkt Specifikationer

Mærke:	Draper
Kategori:	Projektionslærred
Model:	Silhouette V

Har du brug for hjælp?

Hvis du har brug for hjælp til Draper Silhouette V stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Projektionslærred Draper Manualer

Draper Clarion Manual

22 September 2024

Draper Luma 207008 Manual

6 September 2024

Draper DR230109 Manual

4 September 2024

Draper Luma 207009 Manual

9 August 2024

Draper Traveller 230107 Manual

1 August 2024

Draper Silhouette/Series M Manual

31 Juli 2024

Draper Luma Manual

30 Juli 2024

Draper Premier XL Manual

30 Juli 2024

Draper Consul Manual

28 Juli 2024

Draper DR230107 Manual

28 Juli 2024

Projektionslærred Manualer

Nyeste Projektionslærred Manualer

EPV PMT110HT3-ISF Manual

3 April 2025

EPV EF125C-A4K Manual

3 April 2025

ORAY DRAGONFLY 101 x 180 Manual

2 April 2025

Da-Lite Cinema Vision Manual

1 Oktober 2024

Da-Lite Perm-Wall 78676 Manual

26 September 2024

Pyle PRJSM1006 Manual

19 September 2024

EPV PGF106WH1-A4K Manual

5 September 2024

EPV PGF84WH1 Manual

5 September 2024

KHOMO GEAR GER-1252 Manual

4 September 2024

KHOMO GEAR GER-1273 Manual

4 September 2024