INSTALLATION & OPERATING INSTRUCTIONS
1. Unpack unit. Save carton for off-season storage (if needed).
2. Assemble Stand: Pull the cord tight through the pole stand. Turn base on its side
and insert bottom threaded plastic piece into base, connecting to the threaded
plastic cap. Twist threaded plastic cap clockwise to tighten. Complete installation
by aligning upper and lower support tube and inserting the bar sections. (For
more detailed instructions, please refer to assembly guide)
3. Plug cord into an outlet or UL listed extension cord as described in
“IMPORTANT SAFETY INSTRUCTIONS”.
4. Hold the Power switch on the side of the revolving rotation door. Twist the unit
to the “Power ON” position. When you hear a “click”, the machine is turned on.
5. For best catch results leave unit on at all times, except when cleaning or servicing.
6. Catch rate activity will be higher at night. For best catch results it is
recommended to keep the unit away from competing light sources.
For household and commercial, indoor and outdoor use.
7. It is recommended to place the unit at least 20 to 40 feet away from where people will be sitting.
8. This unit is all-weather resistant - designed for indoor and outdoor use, including rainy conditions.
9. To Reduce the Risk of Electric Shock, this appliance has a polarized plug (one blade is wider than the other). This plug
will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not
fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way.
USER MAINTENANCE INSTRUCTIONS - CLEANING
Frequent cleaning will prolong the life of the unit, ensure fire prevention and provide for more efficient operation.
1. Be sure to clean the unit once per week
2. To clean, hold the switch on the revolving rotation door and turn it to the “POWER OFF” position.
After hearing the “click”, the machine is turned off. Unplug the unit.
3. For weekly cleaning, twist the cage clockwise. Remove any buildup from the inside of the retaining cage and fan with a
4 For major cleaning, remove the four screws securing the fan housing to the light housing. After removing the screws,
gently pull the fan housing away from the light housing. Using a soft brush, remove dirt and debris from the light
housing. Once the cleaning process has been completed, align the screw holes in the fan housing with the screw holes in
the lighting unit and tighten the screws to the base of the lighting unit.
5. When replacing the retaining cage – DO NOT press/push against the screen windows.
REPLACING BULB Replace With DynaTrap Bulb #41050 (or equivalent G24 Type - 56V/7W Bulb)
The light bulb life expectancy is approximately 3,000 hours (or about 4 months), and should be replaced regularly to ensure
optimal UV effectiveness. Even though the bulb’s light may be visible to you, its ability to attract mosquitoes diminishes over
1. Turn power switch to “off” position. UNPLUG UNIT, and allow bulb to cool before replacing.
2. Twist the cage clockwise. Turn the unit upside down.
3. Remove the four screws securing the fan housing to the light housing. After removing the screws, gently pull the fan
housing away from the light housing. Using a soft brush, remove dirt and debris from the light housing. Once the clean
ing process has been completed, untighten the screw securing the base of the light bulb to the light housing. Slide the
metal bracket to the side. Cover the bulb with a cloth to protect your finger and hand. Grasp the bulb (with your hand
and fingers protected by the cloth) and gently pull the bulb from the socket.
4. Remove any debris from the lamp socket with a brush before inserting the new bulb. Replace the metal plate over the
base of the bulb and tighten the retaining screw.
5. Align the screw holes in the fan housing with the screw holes in the lighting unit and tighten the screws to the base of the
6. Replace the retaining cage at the bottom of the unit.
Replacement fluorescent bulbs can be found at your local retailer or can
be ordered directly from DynaTrap by calling 1-877-403-TRAP (8727) or
visiting www.DynaTrap.com
Flying insects are attracted to the unit by the UV light and CO2 that is generated
by the photo-catalysis between the UV lamps and the special TiO2 coating.
The fan then pulls the insects into the screened base, trapping them until they
dehydrate and die. The base can be removed, allowing the contents to be
periodically emptied into the trash. The see-through screen shows the insects
trapped in the compartment, alerting you when the cage needs to be emptied.
DYNAMIC guarantees to the original purchaser that this product is free from defective materials and workmanship. This
warranty is limited to remedy any defective part for a period of one year from date of original date of purchase. Retain
your original receipt as proof of purchase. This warranty does not apply to the light bulb, nor to, in our judgment, misuse or
abuse. If this unit has been altered, no warranty is in force. This warranty does not apply if this unit is purchased outside the
United States, excluding Canada and Mexico. In no case shall DYNAMIC be liable for any accidental, punitive, consequential,
or any other damages of any kind for breach of this or any other warranty, expressed or implied, whatsoever. Some states
do not allow limitation on how long an implied warranty lasts, so the above limitation or exclusion may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights that vary from state to state.
41050 7-Watt Replacement UV Fluorescent Bulb (1 piece)
To see all replacement and accessory parts available for your DynaTrap,
including UV-bulbs, fans, retaining cages, and more, visit www.DynaTrap.com.
IMPORTANT, RETAIN FOR FUTURE
REFERENCE: READ CAREFULLY
WARNING: When using electric appliances, basic precautions should always be followed, including the following:
– To disconnect, turn all controls to the off (“O”) position, then remove plug from outlet.
– Unplug from outlet when not in use and before servicing or cleaning.
– To reduce the risk of electrical shock, do not put appliance in water or other liquid.
– This appliance is provided with double insulation. Use only identical replacement parts.
CAUTION: To reduce the risk of injury from moving parts, unplug before servicing.
WARNING: Risk of Electric Shock.
See instructions for Servicing of Double-Insulated Appliances.
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions before using the DynaTrap
Insect Trap and keep for future reference.
1. Always turn unit off and disconnect plug before servicing, cleaning, or changing bulb.
2. Do not position the unit near heat, gas, oil or other flammable materials.
3. Mount product out of reach from children.
4. Never operate this product if it has a damaged cord or plug, if it is not working properly, if it has been dropped or
damaged, or if it has been dropped into water.
5. Do not insert fingers or any foreign objects into the unit while it is connected to an electrical outlet.
6. Collected mosquitoes within the unit may contribute to fire, so clean insects from the unit frequently.
7. Do not clean this product with water spray. Do not place where it can fall into water, or near flammable materials.
8. Do not touch fan while in motion.
9. Do not abuse cord—never carry or hang unit by cord or yank it to disconnect from receptacle. Keep cord away from
heat, oil, or sharp edges.
10. Use only extension cords that are clearly marked “Suitable for Use with Outdoor Appliances” and that have plug and
receptacles that match the product plug. Replace all damaged cords.
11. Only use attachments recommended or sold by the manufacturer.
12. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
13 Do not use the machine on desk or in hand.
14. SERVICING OF DOUBLE-INSULATED APPLIANCES - In a double-insulated appliance, two systems of insulation are
provided instead of grounding. No grounding means is provided on a doubleinsulated appliance, nor should a means
for grounding be added to the appliance. Servicing of a double-insulated appliance requires extreme care and knowl
edge of the system, and should be done only by qualified service personnel. Replacement parts for a double-insulated
appliance must be identical to those parts in the appliance. A double-insulated appliance is marked with the words
“DOUBLE INSULATION” or “DOUBLE INSULATED.” The symbol
Problem: Correction:Possible cause:
1. No electrical power. 1. Check plug, receptacle, and fuse or circuit breaker.
2. Check to make sure power is switched to the “ON” position.
Bulb illuminates, but fan
1. Shorted fan. UNPLUG UNIT: Examine fan to see that it is free from
foreign material, dirt or build-up of dead insects.
Clean unit as in “CLEANING” section.
1. Check all sockets for proper bulb seating and alignment.
2. Replace bulb, if needed, following instructions under
Dynamic Solutions Worldwide, LLC
12247 W. Fairview Ave. Milwaukee, WI 53226
Visit us online at www.DynaTrap.com
©2018 Dynamic Solutions Worldwide, LLC
FOR HOUSEHOLD AND COMMERCIAL,
This device complies with
Performance Standards for Light-
Emitting Products, 21 DFR, Part
Subchapter J, Radiological Health.
This product may be covered by one or more U.S. patents
or pending patent applications. See www.DynaTrap.com/patents
