Electro Harmonix 8-Step Program Manual

Electro Harmonix Ikke kategoriseret 8-Step Program

Læs gratis den danske manual til Electro Harmonix 8-Step Program (25 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Electro Harmonix 8-Step Program, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/25

Set up your MIDI master device to control MIDI CC #24. CC #24 controls the

RATE slider on the 8-STEP.

Send out a range of values on CC #24 from 0 to 127. As the values increase, the

RATE will increase on the 8-STEP.

Now set your MIDI device to output MIDI Program Change #100, this may be

#101 on some devices.

Send MIDI PC #100. When you do the 8-STEP will immediately begin playback,

as if you had pressed the PLAY FSW on the unit. Send PC #100 again to pause

playback.

Check the MIDI chart at the end of this manual for a complete list of all of the

MIDI command assignments and the parameters they control on the 8-STEP.

Changing the 8-STEP’s MIDI Channel

Press and hold the RESET FSW. After 3 seconds you will see the GL and SL LEDs

blink, while the DIR LED is off. At this point the current MIDI channel is

displayed on the digit display.

While continuing to hold down the RESET FSW, turn the MODE knob clockwise to

increment the MIDI channel and counter-clockwise to decrement the MIDI

channel.

The range of available channels is 1 through 16 plus a setting displayed as

where all MIDI channels are recognized. Since there is only one digit available on

the display, the digit’s decimal LED lights up to indicate the tens placeholder. So

Channel 12 is shown by displaying the number 2 plus the decimal LED:

(2.)

Channel 2 would be shown by displaying only the number 2

(2)

To enable all MIDI channels, turn MODE clockwise past Channel 16. An

will be

displayed on the digit, now all MIDI channels are recognized.

Once you have selected your chosen MIDI channel, release the RESET FSW. The

MIDI channel selection remains in memory even after power cycling.

The MIDI channel is a global parameter; it is not saved with presets.

- CONTROLS, INDICATORS & I/O-

The following descriptions detail all of the sliders, knob, switches, LEDs (lights) and I/O jacks

on the 8-STEP PROGRAM:

STEP 1-8 SLIDERS & LEDS

8-STEP’s sequences are composed of up to 8 Steps. Each step has its own independent slider

for setting the expression or CV level. As you push a step slider upward, its output level

increases. When used as an expression pedal replacement, the maximum and minimum

range of each step is equal to the toe (maximum) and heel (minimum) range of an expression

pedal. When the 8-STEP is used as a CV sequencer, the output range is 0V (minimum) to 5V

(maximum).

8-STEP PROGRAM

Analog Expression/CV Sequencer

Congratulations on your purchase of the Electro-Harmonix 8-STEP PROGRAM. The 8-STEP is

an analog sequencer that connects to the expression pedal input of many different types of

effects pedals, keyboards and other devices. Think of the 8-STEP as replacing your

expression pedal, controlling parameters in a sequential fashion rather than continuously as

you normally do with an expression pedal. Additionally, the 8-STEP can be connected to

devices that have Control Voltage (CV) inputs.

Special Features of the 8-STEP PROGRAM:

•

Sequence length is selectable between 1 and 8 steps

•

Four available Direction Modes: Forward, Reverse, Bounce and Random

•

Depth and Glide of the sequence output is encoder adjustable

•

Tap Tempo Footswitch allows you to set the tempo with your foot and can be

divided down for faster tempos from the same tap tempo

•

Three available Play Modes: Loop, 1-Shot and Step-Thru (Manual)

•

Reset Footswitch instantly resets the sequence back to its beginning

•

Expression In allows external control over Rate, Depth, Glide or Sequence Length

•

Expression In doubles as an External CV Clock input allowing the 8-STEP to be

synced to an external clock

•

MIDI IN jack allows the 8-STEP tempo to be synced to MIDI Clock

•

Full MIDI control over every parameter on the 8-STEP

•

Comes supplied with a TRS cable for expression control. Use a standard ¼” TS

instrument cable for CV control (0-5V)

•

Save and load up to 10 presets. Add the optional 8-STEP FOOT CONTROLLER to

save and load up to 100 presets

WARNING:

Your 8-STEP PROGRAM comes equipped with an Electro-Harmonix

9.6DC-200BI power supply (same as used by Boss® & Ibanez®:

9.6 Volts DC 200mA). The 8-STEP requires 100mA at 9VDC with a center

negative plug. The 8-STEP does not take batteries. Using the wrong adapter

may damage your unit and void the warranty.

Produkt Specifikationer

Mærke:	Electro Harmonix
Kategori:	Ikke kategoriseret
Model:	8-Step Program

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix 8-Step Program stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro Harmonix Manualer

Electro Harmonix J Mascis Ram's Head Manual

8 Oktober 2025

Electro Harmonix Anniversary Big Muff Pi Manual

6 Oktober 2025

Electro Harmonix Grand Canyon Manual

6 Oktober 2025

Electro Harmonix Doctor Q Manual

6 Oktober 2025

Electro Harmonix Stereo Memory Man with Hazarai Manual

6 Oktober 2025

Electro Harmonix Next Step Volume Pedal Manual

5 Oktober 2025

Electro Harmonix 8-Step Program Manual

28 September 2025

Electro Harmonix Lizard King Manual

7 September 2025

Electro Harmonix Holy Grail Neo Manual

5 August 2025

Electro Harmonix Pico Rerun Manual

5 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Siemens WG46G2Z9IL Manual

7 December 2025

Atoll DC200 Manual

7 December 2025

Atosa SSTW-2448 Manual

7 December 2025

Advantech ARK-3534B Manual

7 December 2025

Fostex FE166NV2 Manual

7 December 2025

Federal Vision VNSS7260C-SLD Manual

7 December 2025

Metabo RP 18DA Manual

7 December 2025

Alfatron ALF-HDMI-D Manual

7 December 2025

Atosa SSTW-2436 Manual

7 December 2025

SkyRC Immersion GO Manual

7 December 2025