Electro Harmonix Pico Rerun Manual

Electro Harmonix Ikke kategoriseret Pico Rerun

Læs gratis den danske manual til Electro Harmonix Pico Rerun (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Electro Harmonix Pico Rerun, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
RERUN
User Manual
Tape Delay
RERUN
User Manual
Tape Delay
Tails and Analog Bypass Selection
The Rerun allows you to choose between two
bypass modes:
Analog: the bypass signal is fully analog; the
delay effect instantly mutes upon entering
bypass.
to decay naturally upon entering bypass; no new
audio enters the delay block; bypass is digital.
Tails bypass is selected by default from the facto-
ry. To activate Analog bypass, do the following:
1. Press and hold the TYPE push button.
2. After two seconds, the LED enters Party Mode,
where it rapidly cycles through the three LED
colors.
3. Release the button; Analog bypass is now
active.
4. Repeat this same procedure to change back
to Tails bypass.
The bypass mode setting is remembered through
power-cycles so you can set it and forget it.
Maximum Feedback Self-Oscillation
Turn the FDBK knob up to maximum to achieve
runaway self-oscillation. When Tails bypass
mode is enabled, you can also activate maxi-
mum feedback by pressing and holding the
footswitch:
1. Press-and-hold the footswitch.
2. After 500ms, the LED begins flashing through
all three colors. Maximum Feedback is now
active.
3. Release the footswitch to stop self-oscillation
and return the feedback setting to the current
position of the FDBK knob.
Questions about this product? Email: info@ehx.com
Tails and Analog Bypass Selection
The Rerun allows you to choose between two
bypass modes:
Analog: the bypass signal is fully analog; the
delay effect instantly mutes upon entering
bypass.
to decay naturally upon entering bypass; no new
audio enters the delay block; bypass is digital.
Tails bypass is selected by default from the facto-
ry. To activate Analog bypass, do the following:
1. Press and hold the TYPE push button.
2. After two seconds, the LED enters Party Mode,
where it rapidly cycles through the three LED
colors.
3. Release the button; Analog bypass is now
active.
4. Repeat this same procedure to change back
to Tails bypass.
The bypass mode setting is remembered through
power-cycles so you can set it and forget it.
Maximum Feedback Self-Oscillation
Turn the FDBK knob up to maximum to achieve
runaway self-oscillation. When Tails bypass
mode is enabled, you can also activate maxi-
mum feedback by pressing and holding the
footswitch:
1. Press-and-hold the footswitch.
2. After 500ms, the LED begins flashing through
all three colors. Maximum Feedback is now
active.
3. Release the footswitch to stop self-oscillation
and return the feedback setting to the current
position of the FDBK knob.
Questions about this product? Email: info@ehx.com
Welcome to the Electro-Harmonix Rerun Tape Delay:
an extremely compact tape delay modeler with up
to 3 seconds of delay time. The Rerun lets you dial
in repeats with saturation and flutter for lush, organic
delay tones. The pedal features tap-tempo, to keep
the echoes in time with your music, tails mode, to
keep the repeats going after switching to bypass,
and foot accessible maximum feedback for run-
away self-oscillation.
Operating Instructions
Insert the output plug from the supplied 9VDC AC
adapter into the power jack at the top of the Rerun.
The unit must be powered to pass signal, even in
bypass. The Rerun features buffered analog bypass
or digital bypass depending on settings. Connect
an instrument cable from your instrument to the
Input jack. Connect an instrument cable between
the Output jack and a suitable amplifier. Click the
footswitch to engage the pedal and light the LED.
BLEND DELAY
FLUTTER
SAT FDBK
8
9
1 2
5
6
6
3 4
7
Power Suppy Requirements: Voltage: 9VDC Current: 100mA Polarity: Center-Negative
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter or a
plug with the wrong polarity may damage the device and void the warranty. Do not exceed 10.5VDC on the power
plug. Power supplies rated for less than 100mA may cause the device to act unreliably.
Controls & Jacks
1. BLEND Adjusts the output mix from 100% dry
to 100% wet.
2. DELAY Controls the delay time, ranging from
8ms to 3s.
3. SAT Controls the saturation, or distortion, on
the echo repeats.
4. FDBK Controls the number of echo repeats
the Rerun generates. At minimum you get one
repeat, at maximum you get runaway self-os-
cillation.
5. FLUTTER Button Flutter emulates the pitch
modulation that occurs on old, worn-down tape
machines. Press this button to set flutter depth:
Green – LOW FLUTTER
Orange – MEDIUM FLUTTER
Red – HIGH FLUTTER
6. Footswitch and Status LED The footswitch
engages or bypasses the effect. The LED indi-
cates the selected Flutter depth. In bypass
mode, the LED is off. The LED blinks at the lat-
est tap reading when the delay time is set by
tap tempo.
7. Input Jack Impedance: 2.2MΩ, Max In: +1.5 dBu
8. Output Jack Impedance: 680Ω, Max Out: +2.1 dBu
9. Power Jack Current draw: 100mA at 9.0VDC
Tap Tempo
The footswitch can be used to set the delay
time. Press and release the footswitch at least
twice, in time with your music, to set the tempo.
The LED blinks at the tempo to confirm the
delay time is set by tap-tempo. To turn off
tap-tempo, simply turn the DELAY knob to reset
the delay time. You can completely disable
tap-tempo by following these steps:
1. Power down the Rerun.
2. Press and hold the footswitch while reapply-
ing power.
3. Continue to hold the footswitch for about
two seconds; the LED will slowly blink
through all three colors twice.
4. Release the footswitch; tap-tempo is now
disabled.
5. Repeat this process to re-enable tap-tempo.
Tap-tempo disable is recalled through power
cycles so you can set it and forget it.
Welcome to the Electro-Harmonix Rerun Tape Delay:
an extremely compact tape delay modeler with up
to 3 seconds of delay time. The Rerun lets you dial
in repeats with saturation and flutter for lush, organic
delay tones. The pedal features tap-tempo, to keep
the echoes in time with your music, tails mode, to
keep the repeats going after switching to bypass,
and foot accessible maximum feedback for run-
away self-oscillation.
Operating Instructions
Insert the output plug from the supplied 9VDC AC
adapter into the power jack at the top of the Rerun.
The unit must be powered to pass signal, even in
bypass. The Rerun features buffered analog bypass
or digital bypass depending on settings. Connect
an instrument cable from your instrument to the
Input jack. Connect an instrument cable between
the Output jack and a suitable amplifier. Click the
footswitch to engage the pedal and light the LED.
BLEND DELAY
FLUTTER
SAT FDBK
8
9
1 2
5
6
6
3 4
7
Power Suppy Requirements: Voltage: 9VDC Current: 100mA Polarity: Center-Negative
This device comes equipped with an Electro-Harmonix 9.6DC-200 power supply. Use of the wrong adapter or a
plug with the wrong polarity may damage the device and void the warranty. Do not exceed 10.5VDC on the power
plug. Power supplies rated for less than 100mA may cause the device to act unreliably.
Controls & Jacks
1. BLEND Adjusts the output mix from 100% dry
to 100% wet.
2. DELAY Controls the delay time, ranging from
8ms to 3s.
3. SAT Controls the saturation, or distortion, on
the echo repeats.
4. FDBK Controls the number of echo repeats
the Rerun generates. At minimum you get one
repeat, at maximum you get runaway self-os-
cillation.
5. FLUTTER Button Flutter emulates the pitch
modulation that occurs on old, worn-down tape
machines. Press this button to set flutter depth:
Green – LOW FLUTTER
Orange – MEDIUM FLUTTER
Red – HIGH FLUTTER
6. Footswitch and Status LED The footswitch
engages or bypasses the effect. The LED indi-
cates the selected Flutter depth. In bypass
mode, the LED is off. The LED blinks at the lat-
est tap reading when the delay time is set by
tap tempo.
7. Input Jack Impedance: 2.2MΩ, Max In: +1.5 dBu
8. Output Jack Impedance: 680Ω, Max Out: +2.1 dBu
9. Power Jack Current draw: 100mA at 9.0VDC
Tap Tempo
The footswitch can be used to set the delay
time. Press and release the footswitch at least
twice, in time with your music, to set the tempo.
The LED blinks at the tempo to confirm the
delay time is set by tap-tempo. To turn off
tap-tempo, simply turn the DELAY knob to reset
the delay time. You can completely disable
tap-tempo by following these steps:
1. Power down the Rerun.
2. Press and hold the footswitch while reapply-
ing power.
3. Continue to hold the footswitch for about
two seconds; the LED will slowly blink
through all three colors twice.
4. Release the footswitch; tap-tempo is now
disabled.
5. Repeat this process to re-enable tap-tempo.
Tap-tempo disable is recalled through power
cycles so you can set it and forget it.

Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Pico Rerun

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Pico Rerun stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Electro Harmonix Manualer

Electro Harmonix

Electro Harmonix Stereo Memory Man with Hazarai Manual

6 Oktober 2025
Electro Harmonix

Electro Harmonix Next Step Volume Pedal Manual

5 Oktober 2025
Electro Harmonix

Electro Harmonix 8-Step Program Manual

28 September 2025
Electro Harmonix

Electro Harmonix Lizard King Manual

7 September 2025
Electro Harmonix

Electro Harmonix Holy Grail Neo Manual

5 August 2025
Electro Harmonix

Electro Harmonix Pico Rerun Manual

5 August 2025
Electro Harmonix

Electro Harmonix Oceans 11 Reverb Manual

5 August 2025
Electro Harmonix

Electro Harmonix Envelope Filter Manual

5 August 2025
Electro Harmonix

Electro Harmonix 9DC-100 Manual

30 Juli 2025
Electro Harmonix

Electro Harmonix C9 Manual

30 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Clarion

Clarion VT1510E Manual

6 Oktober 2025
Gamko

Gamko KFK/2CS Manual

6 Oktober 2025
Rapid

Rapid RP150 Multi Manual

6 Oktober 2025
Zoom

Zoom 504II Manual

5 Oktober 2025
Metra

Metra XSVI-9004-NAV Manual

5 Oktober 2025
CyberPower

CyberPower CS20A-EBP Manual

5 Oktober 2025
Axkid

Axkid Envirobase Manual

5 Oktober 2025
LG

LG 86QNED85ACA Manual

5 Oktober 2025
Metra

Metra 99-7401 Manual

5 Oktober 2025
Clarion

Clarion OHM1088VD Manual

5 Oktober 2025