Electro Harmonix EHX Tortion Manual

Electro Harmonix Ikke kategoriseret EHX Tortion

Læs gratis den danske manual til Electro Harmonix EHX Tortion (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 21 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 11 anmeldelser. Har du et spørgsmål om Electro Harmonix EHX Tortion, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

EHX TORTION

JFET Overdrive/Preamp

Congratulations on your purchase of the EHX TORTION, the most advanced and

dynamic overdrive pedal on the market today. The EHX TORTION uses analog

JFET technology to reproduce the overdrive and distortion character of a tube

amplifier, all in a compact, durable die-cast chassis. Three-band EQ and a Pre-

Gain switch hone your sound, and a footswitchable BOOST mode adds a second

channel of modern high-gain tones.

WARNING: Your EHX TORTION comes equipped with an Electro-Harmonix 9.6DC-200BI

power supply (same as used by Boss

& Ibanez

: 9.6 Volts DC 200mA). The EHX

TORTION requires 27mA at 9VDC with a center negative plug. Using the wrong adapter

may damage your unit and void the warranty. The EHX TORTION also accepts 9V

batteries, we recommend alkaline.

- MODES OF OPERATION: NORMAL VS. BOOST -

The EHX TORTION operates in two modes: NORMAL and BOOST. The NORMAL

mode uses three JFET stages for low to medium gain sounds. The volume and

gain controls for NORMAL mode are located in the top row of knobs. The boost

mode is activated with the BOOST footswitch, and adds a fourth gain stage for

modern high-gain tones. The BOOST volume and gain knobs are on the bottom

row of the controls. The volume and gain controls for each mode are completely

independent, allowing the two modes to function like two separate channels on a

tube amplifier.

- CONTROLS -

GAIN Knob – The NORMAL GAIN knob is on the top row. This knob controls the

amount of input gain when the pedal is in NORMAL mode. This knob is disabled

when in BOOST mode.

PRE-GAIN Switch This switch controls the level and tone of the initial input –

signal to the EHX TORTION. This switch has four settings. The two leftmost

settings select a lower input level, for vintage plexi tones. The two rightmost

settings are higher gain for a modern, hot-rodded sound. Each pre-gain setting

has two tone selections: Full or Tight, indicated by and . The Full setting has F T

more bass for a bigger sound. The Tight setting focuses the bass frequencies for

a more modern tone.

BASS Knob Controls the level of the bass frequency range. –

MID Knob Controls the level of the middle frequency range. –

TREBLE Knob Controls the level of the treble frequency range. –

VOL Knob The NORMAL VOL knob is on the top row. This knob controls the –

output level of the EHX TORTION when in NORMAL mode. This knob is disabled

when in BOOST mode.

BOOST GAIN Knob The BOOST GAIN knob is on the bottom row. This knob –

controls the amount of input gain when the pedal is in BOOST mode. This knob

is completely independent from the NORMAL GAIN knob, and is disabled when in

Normal mode.

BOOST VOL Knob The BOOST VOL knob is on the bottom row. This knob –

controls the output level of the EHX TORTION when in BOOST mode. This knob

is completely independent from the NORMAL VOL knob, and is disabled when in

Normal mode.

BYPASS Footswitch LED and red – footswitch selects whether the EHX This

TORTION is engaged or in buffered bypass mode. When the effect is engaged,

the red LED will be lit.

BOOST Footswitch and blue LED – This footswitch toggles Boost mode on

and off. When in Boost mode, the blue LED will be lit.

INPUT Jack EHX TORTION. The input – This ¼” jack is the audio input for the

impedance is . 1M

OUTPUT Jack ck is the audio output from the EHX TORTION. The – This ¼” ja

output impedance depends on the VOLUME setting, ranging from k . 250to 25 

BOOST SW Jack Allows an external momentary footswitch to control toggling –

Boost mode on and off. The external switch should be normally open. Upon

engaging the switch, it should create a short circuit between the Tip and Sleeve

of the plug inserted into the BOOST SW jack on the EHX TORTION. Releasing

the switch should open the circuit between the Tip and Sleeve. The BOOST SW

jack is connected in parallel with the BOOST Footswitch so they can both work at

the same time. A suggested momentary footswitch that has been tested with the

EHX TORTION is the Boss FS-5U Momentary Foot Switch.

DI OUTPUT Jack This is a low impedance output capable of driving 600 to –

plug directly into a mixing console or recording equipment. The DI output uses

an all-analog amp/cabinet simulator to create the sound of a real 4x12 cabinet.

Produkt Specifikationer

Mærke:	Electro Harmonix
Kategori:	Ikke kategoriseret
Model:	EHX Tortion

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix EHX Tortion stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Electro Harmonix Manualer

Electro Harmonix Lizard King Manual

7 September 2025

Electro Harmonix Holy Grail Neo Manual

5 August 2025

Electro Harmonix Pico Rerun Manual

5 August 2025

Electro Harmonix Oceans 11 Reverb Manual

5 August 2025

Electro Harmonix Envelope Filter Manual

5 August 2025

Electro Harmonix 9DC-100 Manual

30 Juli 2025

Electro Harmonix C9 Manual

30 Juli 2025

Electro Harmonix EU12AC-1000 Manual

30 Juli 2025

Electro Harmonix Nano Deluxe Memory Man Manual

30 Juli 2025

Electro Harmonix 40DC-100 Manual

30 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Mahlkönig E80S Manual

17 September 2025

Vestil PLB/S-7 Manual

17 September 2025

Quick Dam Flood Gate QDFG30 Manual

17 September 2025

Vestil VHSR-4 Manual

17 September 2025

Kemo M012 Manual

17 September 2025

Vestil COL-4-36-23 Manual

17 September 2025

Vestil BOL-42-4.5 Manual

17 September 2025

Wesco 272937 Manual

17 September 2025

Vestil COL-4-36-44-HDG Manual

17 September 2025

Vestil DR-LOCK Manual

17 September 2025