Electro Harmonix Ring Thing Manual


Læs gratis den danske manual til Electro Harmonix Ring Thing (16 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Electro Harmonix Ring Thing, eller vil du spørge andre brugere om produktet?

Side 1/16
1
RING THING
Single Sideband Modulator
Congratulations on your purchase of the Electro-Harmonix Ring Thing. The Ring Thing has
four selectable modes that utilize either frequency or pitch shift modulation: Ring
Modulation, Single Sideband Upper Band, Single Sideband Lower Band and Pitch Shift. – –
The Ring Modulator section builds upon the original EHX Frequency Analyzer adding to it
selectable carrier waveforms, a sweepable filter, presets and expression pedal control.
Single-sideband modulation is a new effect based on Ring Modulation but where only one
band is present, making it a more harmonious effect. Finally, we have a powerful
modulatable pitch shifter that can do detune effects, vibrato, chorus, transpose or even
whammy when you use an external expression pedal.
Special Features of the Ring Thing:
Four selectable modes: Ring Modulation (RM), Upper Band Modulation (UB),
Lower Band Modulation (LB), Pitch Shift (PS).
Single Sideband frequency shifter with separate simultaneous upper
and lower sideband outputs.
Automatically tune the Ring Modulator to any incoming signal by
pressing and holding the PRESET FSW.
The Ring and SSB Modulators can automatically tune to a note you play on your
instrument
Pitch shifter with range of +/- 2 octaves.
Five modulation waveforms: Square, Sine, Ramp up/down, Triangle.
Expression Pedal control over carrier frequency or pitch shift amount.
Optional external oscillator/modulation input.
Mono Input / Stereo Output in all modes.
Save and load up to 9 presets.
WARNING:
The Ring Thing comes equipped with an Electro-Harmonix 9.6DC-200BI
power supply (same as used by Boss™ & Ibanez™: 9.6 Volts DC 200mA). The Ring
Thing requires 190mA at 9VDC with a plug that is center negative. Using the wrong AC
adapter, even those made by Electro-Harmonix, could cause harm to the unit, the
adapter or you. The Ring Thing does not use batteries.
2
- Quick Start Guide -
BASIC AMPLIFIER CONNECTION SETUP
1. Using an unbalanced instrument cable, plug the output of your instrument into
the INST Input Jack on the right side of the Ring Thing .
2. Connect an unbalanced instrument cable from the MONO L output jack on the
left side of the Ring Thing. Connect the other end of the instrument cable to the
input of a guitar, bass, or keyboard amplifier.
3. Plug the AC Adapter into a wall outlet.
4. Plug the barrel connector of the AC Adapter into the 9V power jack at the top of
the Ring Thing.
Polarity is center negative
.
5. Apply power to the amplifier.
BASIC SETTINGS FOR RING MODULATOR MODE
This mode brings back all the
sounds of the Frequency Analyzer, with a few extras.
1. Connect the Ring Thing as described in Basic Amplifier Connection Setup.
2. Press the BYPASS footswitch so the STATUS LED is on
3. Press the MODE knob so that the Left LED is lit: RM.
4. Turn the following knobs to 50% or 12 oclock: BLEND, WAVE, FINE/DEPTH, and
COARSE.
5. Turn the FILTER/RATE knob fully clockwise.
6. If an expression pedal is plugged in set it to the toe down position.
7. To change the modulation frequency, turn the FINE and/or COARSE knobs.
Automatically Tune the Ring Modulator
Play a single note on your
instrument and then press and hold the PRESET/TUNE footswitch for 1 second. The
Ring Thing will automatically tune its internal modulator to the note you are playing.
This function is monophonic, it is designed to search for the fundamental pitch rather
than figure out what chord is being played. The PRESET/TUNE footswitch can be held
down to continuously tune the ring modulator to the input signal.
The WAVE Function
the WAVE knob sets the waveform of the Ring Modulator
in RM and PS modes. Starting from full counter-clockwise, the choices are: SQUARE,
SINE, RAMP DOWN, RAMP UP, and TRIANGLE. Try turning the knob as you play, you
will notice some waveforms produce more harmonics than others. Additionally you
can crossfade from SQUARE to SINE to RAMP DOWN, then it switches to RAMP UP
and TRIANGLE.
Using an External Oscillator -
To use an external oscillator, as the RM’s carrier,
plug the output of another instrument, recording or mic pre into the MOD input jack
and turn the WAVE knob fully counter-clockwise. The signal at the MOD input jack
will override the Ring Thing’s internal modulator. In RM, UB and LB modes, the


Produkt Specifikationer

Mærke: Electro Harmonix
Kategori: Ikke kategoriseret
Model: Ring Thing

Har du brug for hjælp?

Hvis du har brug for hjælp til Electro Harmonix Ring Thing stil et spørgsmål nedenfor, og andre brugere vil svare dig