Elektrobock PT14 Manual

Elektrobock Termostat PT14

Læs gratis den danske manual til Elektrobock PT14 (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Elektrobock PT14, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

• direct heaters

• rediant panels

• electric ﬂ oor heating

Intended for:

INSTALLATION AND LOCATION

Install the thermostat at a suitable place where its operation cannot be affected by direct ﬂ ow

of hot air from the heater, sunshine or other disturbing effects. Neither install it on an external

wall. The installation height should be approx. 1.5 m above the ﬂ oor. Place the thermostat in

the “reference room”, such as the living room (the heating source will switch according to the

temperature in this room).

The installation must only be done by a properly qualiﬁ ed person!

Before installation, disconnect the power supply!

1) Switch off the main circuit breaker.

2) Loosen the locking screw and remove the front part of the thermostat with the

electronics (Fig. 1).

3) Fix the back part of the thermostat to the wall (Fig. 2).

4) Connect conductors to the terminals acc. to the wiring diagram below, see Fig. 3.

5) Put on the front part of the thermostat with LCD and ensure the thermostat with the

locking screw against splitting.

6) Switch on the main circuit breaker. If everything is OK, the LCD shows the current

temperature.

INSTALLATION PROCEDURE

DESCRIPTION OF THE FUNCTION

The LCD backlight is activated by the ﬁ rst pressing of

or button! Next pressing of this buttons change

the required temperature. Thermostat allows to set-up

temperature in range 3 °C to 39°C.

This temperature can be change by pressing of

and buttons or you can switch between two

temperature levels by pressing / buttons.

For you can set up e.g. 19°C, for e.g. 23°C.

Then you can only in the morning set and in the

evening .

If power failure occurs, then after its restoration is ther-

mostat set on mode on 18°C.

The factory-set is:

18°C

21°C

Theese values are always set up after power failure.

indication of heating

switched ON

Push-button for

temperature

damp

Temperature

mode switch

Push-button for

temperature

increase

Produkt Specifikationer

Mærke:	Elektrobock
Kategori:	Termostat
Model:	PT14

Har du brug for hjælp?

Hvis du har brug for hjælp til Elektrobock PT14 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Elektrobock Manualer

Elektrobock BT730 Manual

31 August 2024

Elektrobock PT712-EI Manual

31 August 2024

Elektrobock PT 32 GST Manual

26 August 2024

Elektrobock BPT 32 Manual

26 August 2024

Elektrobock PT 14 Manual

26 August 2024

Elektrobock PT 713 EI Manual

26 August 2024

Elektrobock PT 713 Manual

26 August 2024

Elektrobock BPT 22 Manual

26 August 2024

Elektrobock BT52 Manual

20 August 2024

Elektrobock BT710 Manual

17 August 2024

Termostat Manualer

Nyeste Termostat Manualer

Tado Bridge X Manual

16 Juni 2025

Carrier ComfortVu Manual

16 Juni 2025

Mainstreet Equipment GMC-12 Manual

15 Juni 2025

Honeywell RTH21B Manual

14 Juni 2025

Tado Wireless Temperature Sensor X Manual

9 Juni 2025

Fantini Cosmi CH123E Manual

26 Marts 2025

Netatmo Smart Radiator Valve Manual

26 Februar 2025

Netatmo Smart Thermostat Manual

26 Februar 2025

Rose LM TER-9 Manual

5 Februar 2025

Rose LM TH-H Manual

1 Februar 2025