Elektrobock PT713-EI Manual


Læs gratis den danske manual til Elektrobock PT713-EI (24 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 67 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 34 anmeldelser. Har du et spørgsmål om Elektrobock PT713-EI, eller vil du spørge andre brugere om produktet?

Side 1/24
MADE IN CZECH REPUBLIC
maintaining minimum oor temperature
monitoring maximum fl oor temperature
PI regulation and predictive system
backup in case of voltage failure > 100 hours
direct installation on junction box
well-arranged backlit display
VENUS switch design
including external sensor
2
DESCRIPTION
PT713-EI is a digital thermostat with a room and oor sensor, specially designed for electric oor heating
control. The internal-external sensor combination provides for the regulation (for setting, see page 8)
of:
1) room temperature (internal sensor) - when comfortable room temperature is required;
(external sensor) - when comfortable room temperature is required; locate the external
sensor in a suitable place where the measured values will not be
distorted;
2) oor temperature (external sensor) - suitable, for instance, for bathrooms where a warm fl oor is
desirable, irrespective of the room temperature;
3) combined (both sensors) - the internal sensor scans the room temperature, and the external
one monitors the maximum fl oor temperature; comfortable room
temperature is required, however, with simultaneous monitoring of
the fl oor temperature (suitable for wooden and laminated fl oors).
Another advantage is the simple installation in KU/KP68 junction boxes by means of the PLUG-IN sys-
tem; the possibility of setting 9 weekly programs with 6 temperature changes per day; regulation type
selection (page 6); as well as other functions for effi cient regulation of the fl oor heating.
INSTALLATION AND LOCATION
Install the thermostat in a suitable place (minimum height of 1.2-1.5 m above the oor) where its
operation will not be affected by direct hot/cold air ows, sunshine or other disturbing infl uences.
Do not mount the thermostat on an exterior wall either. In rooms with increased humidity (bathroom,
kitchen), observe valid standards and install the thermostat as far from the bathtub, shower, basin
or sink as possible.
The external oor sensor (type CT04-10k P, CYXY 2 x 0.5 mm, 10 k , length 3 m, PVC plastic case) Ω
must be located in a fl exible plastic tube embedded in the fl oor, as near to the surface as possible.
The tube must be sealed and protected against in-leak of building materials so that the oor sensor
can be replaced easily if need be. It must not run parallel with power conductors! It can be extended
to a maximum length of 30 metres.
The installation must only be executed by a properly qualifi ed person!
Switch off power supply before installation!
1) Switch off the main circuit breaker.
2) Check that the junction box is placed parallel with the wall.
3) Separate the power part of the thermostat from its microprocessor (main) part; see Fig. 1.
4) Pull the connecting terminals out of the thermostat rear part, see Fig. 2.
5) Connect conductors to the terminals acc. to the wiring diagram below, see page 3 and Fig. 3.
6) Insert the terminals into the thermostat terminals and fasten the power part to the junction
box, see Fig. 4 and 5.
7) Insert the main part connector into the power part and push it; the metal springs must
t in the given holes, see Fig. 6 and 7.
8) Switch on the main circuit breaker; the thermostat is ready for operation.
Note: We recommend you test correct connection after installation, see the TEST function (page 10).


Produkt Specifikationer

Mærke: Elektrobock
Kategori: Termostat
Model: PT713-EI

Har du brug for hjælp?

Hvis du har brug for hjælp til Elektrobock PT713-EI stil et spørgsmål nedenfor, og andre brugere vil svare dig