Epcom TT744 Manual

Epcom AV forlænger TT744

Læs gratis den danske manual til Epcom TT744 (3 sider) i kategorien AV forlænger. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Epcom TT744, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

① DC12V Power Input

② Ethernet Control

③ RS232 Serial Port

④ LOCAL CONTROL PORT: Connect

with receiver extension cable,

receive signal from controller

2. Receiver unit (RX)

1. Plug and play

2. Support 20~60KHz IR pass back

3. Support intelligent EDID management

4. Support resolution up to 1080p@60Hz

5. Transmitter supports four HDMI loop-out

6. Transmission distance is up to 40 meters by CAT6/6A/7

7. Support to switch and select input source device and output

display by both remote control and button on unit device

8. Support IR remote control, Ethernet control and RS232 control

9. Can be powered by network cable. It only needs to connect the 12V

power supply on the transmitter unit, both transmitter and receivers

start work.

1. HDMI source device (DVD, PS3, Set top box, PC etc)

2. HDMI display device like SDTV, HDTV, and projector with

HDMI port.

3. UTP/STP CAT6/6A/7 cable, follow standard IEEE-568B.

Back Panel

① HDMI input indicator

② Switch: To select HDMI input

③ Power indicator

④ IR Receiving window

1 2 3

Remote controller ×1

IR receiver extension

cable ×4

· IMPORTANT SAFETY NOTICE

Please read below safety instructions carefully before installation and

operation:

1. Please pay attention to all the warnings and hints on this device.

2. Do not expose this unit to rain, moisture and liquid.

3. Do not put any stuff into the device.

4. Do not repaire the device or open the enclosure without professional

person guidence to avoid electronic shock.

5. Make sure good ventilation openings to avoid product overheating

damage.

6. Shut off power and make sure environment is safe before installation.

7. Do not plug-in/out the network cables and IR cables when it is in using

to avoid cables damage.

8. Use DC12V/3A only. Make sure the specification matched if using 3

party DC adapters.

Receiver

RJ45 output

HDMI input

HDMI source

HDMI output

HDMI local

output

HDMI display

HDMI Matrix Switch

Power

⑤ EDID

⑥ IR outputs for IR Blasters

⑦ HDMI Inputs

⑧ HDMI local outputs

⑨ RJ45 signal output

· FEATURES

· INSTALLATION REQUIREMENT

This product is a 4×4 HDMI Matrix Switch over network cable, with

4 HDMI inputs, 4 RJ45 output and 4 HDMI loop-out. 4 HDMI outputs

send the high definition audio/video signals to 4 HDTV displays at

local site, and at the same time, 4 RJ45 outputs transmit and extend

the audio/video signals to 4 HDTV displays in 40 meters far away via

4 receivers. RS232 control, Ethernet control, button control and remote

control make switching/ setting the input and output easily. This

product is perfect for security system, digital monitoring system,

school education system, exhibition center, multimedia conference,

command system etc.

• PRODUCT INTRODUCTION

· PACKAGE CONTENTS

5 6

DC12V/3A Power x1

IR blaster extension

cable x4

IR receiver extension cable

(LOCAL CONTROL port)×1

5- White/Blue 6- Green

7- White/Brown 8- Brown

2. Connection

• INSTALLATION PROCEDURES

1. How to make a CAT6/6A/7 network cable

Follow the stanard of IEEE-568B:

1- White/Orange 2- Orange

3- White/Green 4- Blue

1 unit (TX). Matrix Transmitter

· PANEL DESCRIPTION

③

Front Panel

1) Connect HDMI source devices to the transmitter(matrix) inputs via

HDMI cables.

2) If using the HDMI loop-output, connect the HD display devices to

the outputs on the transmitter(matrix) via HDMI cables.

3) Connect the receiver units to the transmitter(matrix) via network

cable, and connect the HD display devices to the HDMI outputs

of the receiver units

4) If using the IR function, connect the IR blaster to the IR OUT on the

transmitter(matrix), and the IR receiver cable to IR IN on the receiver.

5 )Plug the power supply into the Matrix power socket and plug the

power adaptor into a mains socket.

Connection instruction

3. PC Control

The Ehternet RJ45 port is the link for TCP/IP controls, connect to an active

ethernet link with an RJ45 terninater cable.

① The Outputs (TV side) are fixed and cannot be changed.

② Change the Input to display that onto the specified Output TV.

③ These buttons will force the chosen HDMI Input onto all Output TVs.

④ Press OK to confirm.

①

②

HDMI Matrix x1 HDMI Receivers x4

User Manual x1

HDMI source

a browser, please keep try in other browser), then will enter above

interface.

Wall-mount kit ×2pcs

Screws ×6pcs

HDMI source

RJ45 indicator led keeps on with

HDMI signal transmission flashes

with no signal transmission

Produkt Specifikationer

Mærke:	Epcom
Kategori:	AV forlænger
Model:	TT744

Har du brug for hjælp?

Hvis du har brug for hjælp til Epcom TT744 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

AV forlænger Epcom Manualer

Epcom TT388M Manual

29 August 2024

Epcom TT744 Manual

29 August 2024

Epcom TT-676 Manual

28 August 2024

Epcom TT388-DM Manual

28 August 2024

Epcom TT-108-PVR Manual

28 August 2024

Epcom TT372EDID Manual

28 August 2024

Epcom TT-688 Manual

28 August 2024

Epcom TT388DONGLE Manual

28 August 2024

AV forlænger Manualer

Nyeste AV forlænger Manualer

EtherWAN ED3638 Manual

1 November 2025

EtherWAN ED3538 Manual

30 Oktober 2025

Kramer TP-120-OD Manual

21 Oktober 2025

Kramer VM-218DT Manual

17 Oktober 2025

Kramer KIT-401 Manual

16 Oktober 2025

Kramer TP-580CT Manual

16 Oktober 2025

CYP PUV-1230PL-KIT Manual

15 Oktober 2025

Smart-AVI DVX-RXPROS Manual

13 Oktober 2025

Extron FOX3 SR 211 Manual

10 Oktober 2025

Extron FOX3 T 211 Manual

8 Oktober 2025