Erica Synths Fusion Manual

Erica Synths Ikke kategoriseret Fusion

Læs gratis den danske manual til Erica Synths Fusion (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Erica Synths Fusion, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
ERICA FUSION VCO
S
U
B
W
A
V
E
1
S
U
B
M
I
X
C
O
L
O
U
R
S
U
B
W
A
V
E
2
F
R
E
Q
U
E
N
C
Y
W
A
V
E
S
H
A
P
E
F
M
L
E
V
E
L
AUDIO IN 1V/OCTSUBMIX CV FM IN WAVE CV VCO OUT MIX OUT
-2-1
D
R
Y
/
W
E
T
FUSION VCO
THANK YOU FOR ORDERING
ERICA FUSION VCO MODULE!
The Erica Synths Fusion series modules
are designed combining vacuum
tubes and semiconductors therefore
they bring warm, powerful sound and
overdrive possibilities of vacuum tubes
into your modular system. Erica Fusion
series consist of range of modules
used in sound shaping circuit – VCO,
Mixer, real Ringmodulator using
audio transformers and germanium
diode ring, VCF, VCA and Analogue
Delay/Chorus.
Conventional wisdom says that
vacuum tubes have nonlinear
characteristics, and therefore VCOs
based on vacuum tubes need special
tuning for each note.
Erica Synths Fusion VCO is special
kind of VCO – it fuses good tuning
of digital VCO with warm, unique
sound of vacuum tubes that work in
suboscillator circuit. The module has to
vacuum tube based suboscillators: -1
and -2 octaves with plenty of mixing
opportunities for amazing sonic results.
If you wish to go really low frequencies
and have a sound that sets your
modular system apart from mass –
this is exactly module, you need!
FEATURES:
3 basic waveforms with VC morphing
Good 1V/oct tuning
Vacuum tube based suboscillators -1 and -2 oct
Manually and CV controlled -1/-2 oct mixing
Adjustable suboscillator waveshape
Dry/Wet (VCO/suboscillators) mixing
Passive Lowpass filter for extreme subbass sound
Audio input
TECHNICAL SPECIFICATIONS:
Audio input level: .....................................................................................................up to 20V ptp
VCO range: ......................................................................................................................... C1 – C8
Max Output level: ...............................................................................................................10V ptp
Panel width: ............................................................................................................................24HP
Module depth: ..................................................................................................................... 35mm
Power supply: ................. bipolar +-12V , eurorack standard and/or Erica Synths 6VAC PSU
Power consumption:
Tube heater PSU configuration: ..........................60mA@+12V, 30mA@-12V, 300mA@6VAC
Eurorack PSU configuration: ..........................................................215mA@+12V, 185mA@-12V
(NB – start-up power consumption for few seconds is +-250mA)
Choose one of principal
waveforms of VCO
Set the VCO frequency
manually
Dry/Wet potentiometer
provides smooth mix between
pure VCO and pure tube
suboscillator sound
Use COLOUR potentiometer
to filter o higher harmonics
for extreme bass sound and
almost pure sine waveform
on the output. Full CCW
setting works best at really
low frequencies –
C1 and below
Adjust -1 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Adjust a mix between
-1 octave and -2 octaves
suboscillators
Connect 1V/oct
signal to control
VCO frequency
Apply CV to fade
between -1oct
and -2oct mix
Patch
FM CV
here
Apply wave
morphing CV here.
It will be added
to waveshape
potentiometer
setting
This is dry VCO
output, no
suboscillator is
added
This is master output. Get
that fat tube sound here
Adjust -2 octave
suboscillator waverofm from
more harmonic rich CW to
almost sine CCW
Use waveshape
potentiometer to
morph/adjust waveforms.
12 ‘o’clock setting gives
you waveform, selected
by the switch, and then
morphing is applied:
• Sine morphs from
logarythmic wave to
overdriven sine
• Triangle morphs from
ramp to sawtooth
• Pule has adjustable PW –
from 5% to 95%
Patch external VCO (simple
waveforms will work best)
to route it to suboscillator
circuit. Internal VCO will be
automatically disconnected
Adjust FM level with this
potentiometer

Produkt Specifikationer

Mærke: Erica Synths
Kategori: Ikke kategoriseret
Model: Fusion

Har du brug for hjælp?

Hvis du har brug for hjælp til Erica Synths Fusion stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Erica Synths Manualer

Erica Synths

Erica Synths Echolocator Manual

9 September 2025
Erica Synths

Erica Synths Black Hole DSP III Manual

5 September 2025
Erica Synths

Erica Synths Perkons Voice Manual

30 Juli 2025
Erica Synths

Erica Synths Matrix Mixer Manual

30 Juli 2025
Erica Synths

Erica Synths Dual Drive Manual

23 August 2024
Erica Synths

Erica Synths Fusion VCO2 Manual

21 August 2024
Erica Synths

Erica Synths Black DJ VCF Manual

21 August 2024
Erica Synths

Erica Synths Black Dual VCF Manual

19 August 2024
Erica Synths

Erica Synths Pico Multi Manual

19 August 2024
Erica Synths

Erica Synths Hi-Hats A Manual

19 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Biltema

Biltema 25-8844 Manual

27 December 2025
Gamdias

Gamdias Aura GL360 Lcd Manual

27 December 2025
Grässlin

Grässlin talento 111 SK Manual

27 December 2025
Yamazen

Yamazen SUT-202 Manual

27 December 2025
Iogear

Iogear GRMVCH Manual

27 December 2025
Tineco

Tineco Floor One S7 Artist Manual

27 December 2025
Tunturi

Tunturi Cardio Fit T60 Manual

27 December 2025
Boompods

Boompods BOOMCARD Manual

27 December 2025
Akasa

Akasa Newton A-NUC35-M1B Manual

27 December 2025
Yamazen

Yamazen SUT-152 Manual

27 December 2025