Erica Synths Fusion Delay Manual


Læs gratis den danske manual til Erica Synths Fusion Delay (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om Erica Synths Fusion Delay, eller vil du spørge andre brugere om produktet?

Side 1/4
INPUT L OUT R OUTCV IN
C
V
L
E
V
E
L
D
R
Y
/
W
E
T
C
O
L
O
U
R
I
N
L
E
V
E
L
F
E
E
D
B
A
C
K
O
V
E
R
D
R
I
V
E
D
E
L
A
Y
T
I
M
E
M
O
D
.
F
R
E
Q
FUSION DELAY
FLANGER
VINTAGE ENSEMBLE
SHORT
LONG
THANK YOU FOR ORDERING ERICA
FUsION DElAY/FlANGER/VINTAGE
ENsEmblE mODUlE!
The Erica Synths Fusion series modules are
designed combining vacuum tubes and
semiconductors therefore they bring warm,
powerful sound and overdrive possibilities
of vacuum tubes into your modular system.
Erica Fusion series consist of range of
modules used in sound shaping circuit
VCO, Mixer, real Ringmodulator using audio
transformers and germanium diode ring,
VCF, VCA and Analogue Delay/Flanger.
Erica Synths Fusion Delay/Flanger/Vintage
Ensemble module is distinct multifunctional
analogue eects module that combines
BBD chip based eects with an adjustable
tube overdrive in the delay output and
feedback path for extra thickness of sound.
For more flexibility, lowpass filtering is fully
adjustable from none to extreme. Special
feature, not found in eurorack, is Vintage
Stereo Ensemble – eect that’s common on
vintage synthesizers to create moving and
thick spatial sound from a monaural tone
generator, be it FM, DCO or any other kind.
Such a spatial eect is achieved by mixing
dry source with delayed and lowpass
filtered out of phase signal.
FEATUREs:
2 BBD chips (1024 and 4096 stages)
Delay and Flanger eects
Vintage Ensemble Stereo eect
Tube overdrive in the delay output and feedback path
Dry/Wet mixing
Passive Lowpass filter for extreme subbass sound
TECHNICAl sPECIFICATIONs:
Audio input level: up to 20V ptp .....................................................................................................
Max delay time SHORT setting: 20ms ..........................................................................................
Max delay time LONG setting: 200ms .........................................................................................
LFO range: 0,1Hz – 30Hz .................................................................................................................
Panel width: ............................................................................................................................20HP
Module depth: 35mm .....................................................................................................................
Power supply: bipolar +-12V , eurorack standard and/or Erica Synths 6VAC PSU .................
Power consumption:
Tube heater PSU configuration: 35mA@+12V, 20mA@-12V, 300mA@6VAC ..........................
Eurorack PSU configuration: ........................................................... 35mA@+12V, 185mA@-12V
(NB – start-up power consumption for few seconds is -250mA)
Adjust Delay time
manually! Full CW setting
will give you extreme
delays and obscure eects
Use COLOUR
potentiometer to filter
o higher harmonics for
extreme bass sound. Full
CCW setting works best at
really low frequencies
C1 and below
Select between 1024 and
4096 stage delay!
Adjust eect feedback
manually! Turning the
know CW will initiate self
oscillation
This knob provides smooth
mix between Dry and Wet
signals
These are Left and Right outputs.
To enjoy Vintage Ensemble eect,
use stereo mixer.
Adjust manually internal
modulation LFO frequency
that alters BBD sample rate
and thus delay time
Adjust overdrive level form
none to extreme in full
CW setting. This is dual
potentiometer that controls
tube overdrive level in the
delay output and feedback
path simultaneously.
Try it with guitar!
Adjust input audio signal
level! Fusion modules are
sensitive to input signal
levels too high input
signals give interesting
overdrive eects, but
reduce brightness of
delay eect
This is internal and external
modulation level attenuator
Connect audio
signal here!
Patch an external modulation
sinal (LFO, EG, etc) here.
Internal LFO will be
automatically disconnected
Erica Fusion DElay
You can configure Erica Fusion modules for two PSU options.
1. When used with easy to install 6VAC Erica Tube heater PSU, Fusion modules have insignificant (max 35 mA) power consumption from
eurorack PSU. Erica Fusion 6VAC PSU is designed to power up to 7 Erica Fusion modules, but your eurorack case needs 220VAC or 110VAC
routed inside the case (this is typical for most Doepfer cases and some other producers that use switching PSU). Latest Erica Synths cases
have Fusion tube heater connectors on integrated PSU boards.
2. When configured to work with standard +-12V eurorack PSU, power consumption is about 35mA@+12V and 185mA@-12V, and you do not
need to install Fusion PSU. This configuration is the best for Make Noise and similar PSU systems that route only +12V in the case and use
switching ICs to generate +-12V.
For +-12V operation install 2 jumpers
on the tube heater connector on the
left side as shown on the picture!
For 6VAC operation from the Fusion
PSU, install jumpers on the right side.
Also, you can refer to small 12V or 6V
notes next to jumpers
For +-12V operation install 2 jumpers
on the Fusion PSU connector as
shown on the picture. If you use this
module with the Erica Fusion PSU,
no need to install these jumpers. You
connect Fusion PSU ribbon cable
here.
Erica Fusion DElay


Produkt Specifikationer

Mærke: Erica Synths
Kategori: Ikke kategoriseret
Model: Fusion Delay

Har du brug for hjælp?

Hvis du har brug for hjælp til Erica Synths Fusion Delay stil et spørgsmål nedenfor, og andre brugere vil svare dig