EtherWAN EX48000 Manual


Læs gratis den danske manual til EtherWAN EX48000 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om EtherWAN EX48000, eller vil du spørge andre brugere om produktet?

Side 1/2
Hardened Web-Smart High Power PoE Ethernet Switch
This quick start guide describes how to install and use the Hardened Web-Smart High Power PoE (Power
over Ethernet) Ethernet Switch. This is the switch of choice for harsh environments constrained by space.
Physical Description
The Port Status LEDs and Power Inputs
LED State Indication
Steady Power on.
Power1
Power2
Power3
Off Power off.
Steady
Power redundant system failure
occurred.
Fault
Off
Power redundant system failure is
not occurred.
10/100Base-TX, 100Base-FX/BX
Steady
A valid network connection
established.
Link/ACT
Flashing
Transmitting or receiving data.
ACT stands for ACTIVITY.
Steady Valid port connection at 100Mbps.
10/100
Off Valid port connection at 10Mbps.
Steady Powered Device (PD) is connected.
PoE
Off
Powered Device (PD) is
disconnected.
Power Input Assignment
Power3 55VDC DC Jack
55VDC
Power2
Power Ground
55VDC
Power1
Power Ground
Earth Ground
Terminal Block
Relay Output Rating 1A @ 24VDC
Relay Alarm Assignment
FAULT
*Relay warning signal disable for following:
1. The relay contact closes if Power1 and
Power2 are both failed but Power3 on.
2. The relay contact closes if Power3 is failed
but Power1 and Power2 are both on.
The 10/100Base-TX and 100Base-FX/BX Connectors
The 10/100Base-TX Connections
The following lists the pinouts of 10/100Base-TX ports.
Pin PoE Ports (Port 1-4) Non-PoE Port (Port 5)
1 Output Transmit Data + Output Transmit Data +
2 Output Transmit Data - Output Transmit Data -
3 Input Receive Data + Input Receive Data +
4 Positive (VCC+)
5 Positive (VCC+)
6 Input Receive Data - Input Receive Data -
7 Negative (VCC-)
8 Negative (VCC-)
The 100Base-FX Connections
The fiber port pinouts
The Tx (transmit) port of device I is connected to the Rx (receive) port of device II,
and the Rx (receive) port of device I to the Tx (transmit) port of device II.
The WDM 100Base-BX Connections
The fiber port pinouts
Only one optical fiber is required to transmit and receive data.
Functional Description
Meets NEMA TS1/TS2 Environmental requirements such as temperature, shock, and vibration for
traffic control equipment.
Meets EN61000-6-2 & EN61000-6-4 EMC Generic Standard Immunity for industrial environment.
Manageable via Web browser interface.
Port 1 – 4 support Power over Ethernet (PoE) Power Sourcing Equipment (PSE).
High Power PoE design up to 30W.
Supports 802.3/802.3u/802.3x. Auto-negotiation: 10/100Mbps, full/half-duplex. Auto MDI/MDIX.
100Base-FX: Multi mode/Single mode SC or ST type. 100Base-BX: WDM Multi mode/Single mode
SC type.
Supports 1024 MAC addresses. Provides 512K bits memory buffer.
Alarms for power and port link failure by relay output.
Power Supply: Redundant 55VDC Terminal Block power inputs and 55VDC DC JACK with optional
100-240VAC external power supply.
Operating voltage and Max. current consumption: 2.36A @ 55VDC. Power consumption: 130W
Max.
-40 to 75 (℃℃-40 to 167) operating temperature range. Tested for functional operation @
-40 to 85 ( -40 to 185).
Supports Wall and Desktop Mounting installation.
1 V3


Produkt Specifikationer

Mærke: EtherWAN
Kategori: Ikke kategoriseret
Model: EX48000

Har du brug for hjælp?

Hvis du har brug for hjælp til EtherWAN EX48000 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret EtherWAN Manualer

EtherWAN

EtherWAN EX48000 Manual

29 Oktober 2025
EtherWAN

EtherWAN EL100C Manual

19 Juli 2025
EtherWAN

EtherWAN EL100T Manual

11 December 2024
EtherWAN

EtherWAN EL100C-20 Manual

11 December 2024
EtherWAN

EtherWAN EL100T-20 Manual

10 December 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer