EtherWAN EX75900 Manual

EtherWAN bryter EX75900

Læs gratis den danske manual til EtherWAN EX75900 (2 sider) i kategorien bryter. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om EtherWAN EX75900, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

W70G-EX75900Q3 Page 1

Installation Guide

EX75900 Series | Hardened Managed PoE Ethernet Switch

Unpacking

Open the carton and unpack the items. Your package should include:

▪ One EX75900 switch

▪ One RJ-45 console cable

▪ Rack-mounting hardware brackets

If any items are missing or damaged, notify your EtherWAN representative. If

possible, save the carton and packing material in case you need to ship or store the

switch in the future.

What Else You Need

▪ Appropriate cables for data ports. To prevent damage to the switch from

electrical surges, it is recommended to use STP (Shielded twisted pair)

cabling.

▪ Personal computer or laptop

Select a Location

▪ Desktop installations: Mount on a flat table or shelf surface.

▪ Rack installations: Use a 19-inch (48.3-centimeter) EIA standard equipment

rack that is grounded and physically secure.

▪ Choose a dry area with ambient temperature between -40 and 75ºC (-40

and 167ºF).

▪ Keep away from heat sources, sunlight, warm air exhausts, hot-air vents,

and heaters.

▪ Be sure there is adequate airflow.

Connect to the Data Ports

Depending on the model, your switch can have the following ports:

▪ 24 10/100/1000Base-TX PoE ports

▪ 4 1G SFP or 4 1G/10G SFP slots

10/100/1000BASE-TX Ports

Ports that support Power over Ethernet provide power to networked devices such

as IP Phones, Wireless LAN Access Points, and IP security cameras. Total power

budget is 720 Watts, 60 Watts per port.

1G/10G SFP Ports

SFP transceivers can be installed directly into SFP slots. Ensure that the same type

of transceiver is used at both ends of the link and that the correct type of fiber

cable is used.

Connect DC Power

The switch has two terminal block power inputs. Only one power input is required

to operate the switch. However, redundant power supply functionality is

supported. Input voltage is 52-57 VDC.

Relay Output Alarm

The switch provides relay output contacts for signaling of a user-defined power or

port failure. The relay output can be connected to an alarm signaling device.

Current is 0.5A at 48VDC.

3 Normal Open | 2 Ground | 1 Normal Close

Power-Up Sequence

When the switch is powered up:

▪ All Link/ACT LEDs blink momentarily.

▪ The Power LED light goes ON.

▪ Booting ⮕ The Alarm LED goes ON

▪ System ready ⮕ The Alarm LED goes off

Front Panel LEDs

LED

Color

Status

Power 1 & 2

Green

On: Power on

Off: Power off

Link/Act

Green

On: Network connection established

Flashing: Port sending or receiving data

PoE

Amber

ON = Powered Device is connected

Off = Powered Device is disconnected

Alarm

Red

Link down or power down

Digital IO-Setting

Connecting the Digital Inputs

The pin definitions for the digital input module are shown below. Each digital input

consists of two contacts on the 5-pin connector located on the top of the switch. The

inputs can be wired as either dry or wet contacts.

Dry Contacts:

[DI1-/GND] [DI2-/GND]

Logic level 1: Close to GND

Logic level 0: Open

Wet Contacts:

[DI1+/DI1-] [DI2+/DI2-]

Logic level 1 (High): 13~30 Volts

Logic level 0 (Low): 0~3 Volts

Configuring Digital Input Alarms Using the Web Interface

Located under the Diagnostics group, the Digital IO-Setting page allows for quick

configuration and enabling of digital input and environmental alarms.

Produkt Specifikationer

Mærke:	EtherWAN
Kategori:	bryter
Model:	EX75900

Har du brug for hjælp?

Hvis du har brug for hjælp til EtherWAN EX75900 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bryter EtherWAN Manualer

EtherWAN EX17008 Manual

4 November 2025

EtherWAN EX78900X Manual

4 November 2025

EtherWAN EX75000 Manual

3 November 2025

EtherWAN EasyPoE Box Manual

2 November 2025

EtherWAN EG97023 Manual

2 November 2025

EtherWAN ED3601 Manual

2 November 2025

EtherWAN InfraGreEn IG5 Manual

2 November 2025

EtherWAN EX26484 V2 Manual

2 November 2025

EtherWAN EX78162 Manual

1 November 2025

EtherWAN EX17082A Manual

1 November 2025

bryter Manualer

Nyeste bryter Manualer

D-Link DMS-1016 Manual

3 November 2025

D-Link DMS-1024 Manual

3 November 2025

F-Tronic JUMBO60+10 Manual

3 November 2025

Dahua Technology PFS3210-8ET2GF-96 Manual

26 Oktober 2025

TP-Link Omada DS106GPP Manual

19 Oktober 2025

Draytek VigorSwitch PQ2200xb Manual

17 Oktober 2025

Kramer VS-88H2 Manual

16 Oktober 2025

Lancom GS-3126X Manual

16 Oktober 2025

Lancom GS-2310 Manual

16 Oktober 2025

Lancom GS-3628X Manual

16 Oktober 2025