EXSYS EX-13102 Manual


Læs gratis den danske manual til EXSYS EX-13102 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om EXSYS EX-13102, eller vil du spørge andre brugere om produktet?

Side 1/2
6 5
Das EX 13102 USB zu RS485 UART Konverter Board besteht aus einer Platine mit fest - -
montiertem USB Stecker und einem FTDI Chip FT232RL, der alle USB Signale und Protokolle - - - -
verarbeitet. Es eignet sich ideal für Testzwecke oder zum erstellen von USB zu Seriell Kabeln
nach eigenen Kriterien.
Kompatibilität: USB 1.1, 2.0 & 3.2
Betriebssysteme: Windows 9.x / ME / 2000 / XP / Vista / 7 / 8.x / 10 / 11 / Server 20xx/
Linux / MAC
Anschlüsse: 1x USB 2.0 A Stecker, 1x 3 Lötpunkte seriell RS - -485
Zertifikate:
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitun
Vers. 1.0 / 30.10.23
E 1310
ANSCHLÜSSE & STATUS LED S
RS- - 485 Anschlussbelegung 2 Draht:
CONNECTORS & STATUS LED S
CLEANING
USB 2.0 A Plug:-
HARDWARE INSTALLATION
DRIVER INSTALLATION
Because there are large differences between PCs, we can give you only a general installation
guide for the EX 13102. Please refer your computers reference manual whenever in doubt.-
1. - - Connect the EX 13102 USB to the USB A Port at the your PC.
2. When you are ready you can start your PC and continue with the point Driver Installation“.
Windows
After the hardware installation Windows will recognize the device automatically and install the
drivers. If the driver shoul not be installed automatically, please download the driver from our
homepage (www.exsys.de / www.exsys.ch) first. Now select the folder with your operating
system and install the driver. Follow the hardware assistant and finish the installation.
Important! Restart your PC in any case after installing the drivers.
CHECK INSTALLED DRIVER
Open the . Now you should see at >Device manager< Ports (COM & LPT) USB and -
Controller the following new entry:
If you see this or a similar information the device is installed correctly.
To clean the unit, use only a dry, lint free cloth and apply light pressure to remove dirt. Be -
careful not to leave any fibres of the cloth in the connector area.
Never use a damp or wet cloth for cleaning!
USB 2.0 A Plug-
Pin Pin Signal Signal
1 VCC 3 DATA+
2 DATA 4 GND -
Switzerland:
EXSYS Vertriebs GmbH
Dübendorfstrasse 17
8602 Wangen
www.exsys.ch
Germany:
EXSYS Vertriebs GmbH
Industriestrasse 8
61449 Steinbach
www.exsys.de
USB A Stecker -
zum Anschluss an PC
3 Lötpunkte seriell RS-485
Lötpunkte
Pin Pin Signal Signal
1 GND 3 DATA+ (A)
2 DATA (B) -
Lötpunkte:
3 1 2


Produkt Specifikationer

Mærke: EXSYS
Kategori: Ikke kategoriseret
Model: EX-13102

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-13102 stil et spørgsmål nedenfor, og andre brugere vil svare dig