EXSYS EX-41084 Manual

EXSYS Ikke kategoriseret EX-41084

Læs gratis den danske manual til EXSYS EX-41084 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 7 anmeldelser. Har du et spørgsmål om EXSYS EX-41084, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6 5

Die EX 41084 ist eine PCI serielle RS 232 Karte mit 4 seriellen FIFO 16C550 Ports, für den - -

Anschluss von High Speed seriellen RS 232 Peripherie Geräten (z.B. Terminal, Modem, Plotter - -

usw.). Der serielle PCI Bus unterstützt dabei optimal die Leistung des schnellen FTDI Chipset.

Die Karte gewährleistet so eine sichere Datenübertragung und exzellente Performance von bis

zu 921.6KBaud/s! Sie unterstützt alle PCI & PCI X Slots mit 3.3V und 5Volt. Es ist nicht möglich -

die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte vom

System (BIOS) und vom Betriebssystem automatisch vorgenommen werden. Die EX 41084 -

bietet Ihnen die Möglichkeit, +5V und +12V auf Pin 1 und Pin 9 der seriellen Anschlüsse zur Verfü-

gung zu stellen.

Kompatibilität: PCI & PCI X, 5Volt oder 3,3Volt -

Betriebssysteme: Windows 9.x/ ME/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ MAC

Anschlüsse: 4x 9 Pin D Sub serieller Stecker -

Lieferumfang: EX 41084, Oktopus Kabel, Treiber CD, Anleitung -

Zertifikate:

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.0 / 19.06.19

E 4108

ANSCHLÜSSE & JUMPER EINSTELLUNG

DB 9M:

Pin Signal Pin Signal Pin Signal

1 CDC 4 DTR 7 RTS

2 RXD 5 GND 8 CTS

3 TXD 6 DSR 9 RI

9 Pin Stecker Seriell RS 232-

HARDWARE INSTALLATION

DRIVER INSTALLATION

If you are ready with the jumper settings, please proceed with the following installation instructions.

Because there are large differences between PC’s, we can give you only a general installation

guide. Please refer to your computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/ or sides panels of your Computer and

gently slide the cover off.

3. Locate an available PCI expansion slot and remove its covers from the rear panel of your

computer. Make sure it is the right PCI expansion slot for the card (see card description)

4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make sure

the card is seated and oriented correctly. Never insert the card by force!

5. Then connect the card with a screw to the rear panel of the computer case.

6. Gently replace your computer’s cover and the mounting screws.

Windows

After the hardware installation Windows will recognize the card automatically and install the

drivers. If the driver should not be installed automatically, please insert the Driver CD into your

CD Rom drive (e.g. Drive D:) and open the folder „USB_to_IO/FTDI“. Please select the folder -

with your operating system and install the driver (see Picture). Follow the hardware assistant

and finish the installation. Restart your PC in any case after installing the drivers.Important!

CONNECTORS & JUMPER SETTING

CHECK INSTALLED DRIVER

Open the . Now you should see at „>Device manager< Ports (COM & LPT) USB“ and „ -

Controller “ the following new entry’s:

If you see this or a similar information the device is installed correctly.

S1 S4:- 37 Pin Stecker zu

4x 9Pin Serieller Anschluss

S1~S4_PWR: Power auf Pin 1 oder Pin 9

- des RS 232 Stecker Ein/Aus

S1 S4_PWR:-

+5V to Pin1

+12V to Pin1

+5V to Pin9

+12V to Pin9

No Power Supplied on Pin1 or Pin9

Pin1= DCD

Pin9= RI

(Factory Setting)

S1 S4_PWR Jumper Setting-

DCD RI

5V P#1 12V P#9 5V

DCD RI

5V P#1 12V P#9 5V

DCD RI

5V P#1 12V P#9 5V

DCD RI

5V P#1 12V P#9 5V

DCD RI

5V P#1 12V P#9 5V

DB37F:

37 Pin Serial RS 232 Female Connector-

Pin Signal Pin Signal Pin Signal

1 NC 14 RXD2 27 CTS3

2 DCD4 15 RI1 28 RXD3

3 GND 16 DTR1 29 RI2

4 CTS4 17 DSR1 30 DTR2

5 RXD4 18 RTS1 31 DSR2

6 RI3 19 TXD1 32 RTS2

7 DTR3 20 RI4 33 TXD2

8 DSR3 21 DTR4 34 DCD1

9 RTS3 22 DSR4 35 GND

10 TXD3 23 RTS4 36 CTS1

11 DCD2 24 TXD4 37 RXD1

12 GND 25 DCD3

13 CTS2 26 GND

Produkt Specifikationer

Mærke:	EXSYS
Kategori:	Ikke kategoriseret
Model:	EX-41084

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-41084 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret EXSYS Manualer

EXSYS EX-62030MPOE Manual

3 December 2025

EXSYS EX-62030MPOE-SFP Manual

2 December 2025

EXSYS EX-6009POE Manual

30 November 2025

EXSYS EX-6083 Manual

28 November 2025

EXSYS EX-46022 Manual

27 November 2025

EXSYS EX-6008POE Manual

26 November 2025

EXSYS EX-42372 Manual

12 November 2025

EXSYS EX-1334HMV-2 Manual

12 November 2025

EXSYS EX-1331TTL-VIS Manual

12 November 2025

EXSYS EX-44044-2 Manual

12 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Wind River KG250 Manual

17 December 2025

Vaxcel T0450 Manual

17 December 2025

Akasa Newton A-NUC13-M1B Manual

17 December 2025

Gamdias Aura GC9M ARGB Manual

17 December 2025

Wine-Mate WM-6500SSDWC Manual

17 December 2025

ORNO OR-CR-297 Manual

17 December 2025

Sanus VF2022 Manual

17 December 2025

Wine-Mate WM-2500SSW Manual

17 December 2025

Wine-Mate WM-6500SSR Manual

17 December 2025

Vinotemp BR-MW OH16-S Manual

17 December 2025