EXSYS EX-41088 Manual


Læs gratis den danske manual til EXSYS EX-41088 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om EXSYS EX-41088, eller vil du spørge andre brugere om produktet?

Side 1/2
6 5
Die EX 41088 ist eine PCI serielle RS 232 Karte mit 8 seriellen FIFO 16C550 Ports, für den - -
Anschluss von High Speed seriellen RS 232 Peripherie Geräten (z.B. Terminal, Modem, Plotter - -
usw.). Der serielle PCI Bus unterstützt dabei optimal die Leistung des schnellen FTDI Chipset.
Die Karte gewährleistet so eine sichere Datenübertragung und exzellente Performance von bis
zu 115.2KBaud/s! Sie unterstützt alle PCI & PCI X Slots mit 3.3V und 5Volt. Es ist nicht möglich -
die I/O Adressen und Interrupts manuell einzustellen, da die Einstellungen der Karte vom
System (BIOS) und vom Betriebssystem automatisch vorgenommen werden.
Kompatibilität: PCI & PCI X, 5Volt oder 3,3Volt -
Betriebssysteme: Windows 9.x/ ME/ 2000/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ MAC
Anschlüsse: 8x 9 Pin D Sub serieller Stecker -
Lieferumfang: EX 41088, Oktopus Kabel, Treiber CD, Anleitung -
Zertifikate:
1
BESCHREIBUNG & TECHNISCHE DATEN
AUFBAU
Anleitun
Vers. 1.0 / 05.02.19
E 4108
ANSCHLÜSSE
DB 9M
Pin Signal Pin Signal Pin Signal
1 CDC 4 DTR 7 RTS
2 RXD 5 GND 8 CTS
3 TXD 6 DSR 9 RI
9 Pin Stecker Seriell RS 232-
HARDWARE INSTALLATION
DRIVER INSTALLATION
If you are ready with the jumper settings, please proceed with the following installation instructions.
Because there are large differences between PC’s, we can give you only a general installation
guide. Please refer to your computer’s reference manual whenever in doubt.
1. Turn off the power to your computer and any other connected peripherals.
2. Remove the mounting screws located at the rear and/ or sides panels of your Computer and
gently slide the cover off.
3. Locate an available PCI expansion slot and remove its covers from the rear panel of your
computer. Make sure it is the right PCI expansion slot for the card (see card description)
4. Align the card with the expansion slot, and then gently but firmly, insert the card. Make sure
the card is seated and oriented correctly. Never insert the card by force!
5. Then connect the card with a screw to the rear panel of the computer case.
6. Gently replace your computer’s cover and the mounting screws.
Windows
After the hardware installation Windows will recognize the card automatically and install the
drivers. If the driver should not be installed automatically, please insert the Driver CD into your
CD Rom drive (e.g. Drive D:) and open the folder „USB_to_IO/FTDI“. Please select the folder -
with your operating system and install the driver (see Picture). Follow the hardware assistant
and finish the installation. Restart your PC in any case after installing the drivers.Important!
CONNECTORS
CHECK INSTALLED DRIVER
Open the . Now you should see at >Device manager< Ports (COM & LPT) USB and -
Controller the following new entry’s:
If you see this or a similar information the device is installed correctly.
Pin Signal Pin Signal Pin Signal
1 TXD 1 22 RXD 1 43 CTS 1
2 DTR 1 23 DSR 1 44 RTS 1
3 RXD 2 24 DCD 1 45 GND
62 Pin Serial RS 232 Female Connector-
4 DSR 2 25 TXD 2 46 CTS 2
5 DCD 2 26 DTR 2 47 RTS 2
6 TXD 3 27 RXD 3 48 CTS 3
7 DTR 3 28 DSR 3 49 RTS 3
8 RXD 4 29 DCD 3 50 GND
9 DSR 4 30 TXD 4 51 CTS 4
10 DCD 4 31 DTR 4 52 RTS 4
11 RXD 5 32 GND 53 CTS 5
12 DSR 5 33 TXD 5 54 RTS 5
13 DCD 5 34 DTR 5 55 GND
14 TXD 6 35 RXD 6 56 CTS 6
15 DTR 6 36 DSR 6 57 RTS 6
16 RXD 7 37 DCD 6 58 GND
17 DSR 7 38 TXD 7 59 CTS 7
18 DCD 7 39 DTR 7 60 RTS 7
19 RXD 8 40 GND 61 CTS 8
20 DSR 8 41 TXD 8 62 RTS 8
21 DCD 8 42 DTR 8
DB62F:
S1 S4:- 62 Pin Stecker zu 8x 9Pin
Serieller Anschluss


Produkt Specifikationer

Mærke: EXSYS
Kategori: Ikke kategoriseret
Model: EX-41088

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-41088 stil et spørgsmål nedenfor, og andre brugere vil svare dig