EXSYS EX-48210 Manual

EXSYS Ikke kategoriseret EX-48210

Læs gratis den danske manual til EXSYS EX-48210 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 24 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 12.5 anmeldelser. Har du et spørgsmål om EXSYS EX-48210, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

6 5

Die EX 48210 ist eine M.2 Karte zur Umsetzung auf zwei RS 422/485 Schnittstellen mit FIFO - -

16C550 Port für den Anschluss von High Speed Seriellen RS-422/485 Peripherie Geräten (z.B.

Modem, Plotter usw.). Die EX 48210 nutzt den Exar Chipsatz, der die neueste High Speed- - -

Interface Technologie beinhaltet. Die Karte gewährleistet so eine sichere Datenübertragung und -

exzellente Performance von bis zu 921.6 KBaud/s für jedes angeschlossene serielle Gerät! Sie

unterstützt den M.2 NGFF Bus mit A Key. Es ist nicht möglich die I/O Adressen und Interrupts -

manuell einzustellen, da die Einstellungen der Karte vom System (BIOS) und beim installieren

des Betriebssystems automatisch vorgenommen werden.

Kompatibilität: M.2 NGFF mit A Key -

Betriebssysteme: Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx/ Linux/ QNX 6.0

Anschlüsse: 2x 9 Pin Stecker Seriell RS 422/485 -

Lieferumfang: EX 48210, 2x Flachbandkabel, Treiber CD, Anleitung -

Zertifikate:

BESCHREIBUNG & TECHNISCHE DATEN

AUFBAU

Anleitun

Vers. 1.0 / 20.02.19

E 4821

ANSCHLÜSSE & JUMPERS

9 Pin Stecker Seriell

RS 422 & RS 485 4 Draht- - -

Pin Signal Pin Signal

1 TXD 6 NC -

2 TXD+ 7 NC

3 RXD+ 8 NC

4 RXD 9 RI -

5 GND

DB 9M

DRIVER INSTALLATION

Windows CE

After starting Windows is recognizes a new . Insert the driver CD into „Serial PCI Connector“-

you CD ROM drive (eg drive D:) and then use the driver which located in the folder „windows -

CE 6 7“ (see picture):

Linux

After starting Linux is recognizes a new . Insert the driver CD into you „Serial PCI Connector“-

CD ROM drive (eg drive D:) and then use the driver which located in the folder „Linux“ (see -

picture):

QNX

After starting the system is recognizes a new . Insert the driver CD into „Serial PCI Connector“-

you CD ROM drive (eg drive D:) and then use the driver which located in the folder „QNX“ (see -

picture):

COM1&COM2: 2x 10 Pin Floppy Anschluss für

- RS 422/485 9 Pin Flachbandkabel

JP3: Jumper zur Einstellung

des Mode am COM1

JP5: Jumper zur Einstellung

des Mode am COM2

HARDWARE INSTALLATION

DRIVER INSTALLATION

Please note the following installation instructions. Because there are large differences between the

PC’s, we can give you only a general installation instructions for the EX 48210. Please refer your -

computer’s reference manual whenever in doubt.

1. Turn off the power to your computer and any other connected peripherals.

2. Remove the mounting screws located at the rear and/or sides panels of your Computer and

gently slide the cover off.

3. Now connect the two Ribbon Cable with the 10 Pin Floppy Connectors at the EX 48210. -

4. Now set the Jumper JP3 & JP5 in the desired mode (see Connectors & Jumpers).

5. Locate an available M.2 NGFF expansion slot and insert the card. Make sure that the card is

plugged in correctly.

6. Gently replace your computer’s cover and the mounting screws.

Windows 200x/ XP/ Vista/ 7/ 8.x/ 10/ Server 20xx

After starting Windows is recognizes a new . Insert the driver CD into „Serial PCI Connector“-

you CD ROM drive (eg drive D:) and then start the installer -„xr17v35x_win_single_installer“

which located in folder „Ver_5100_installer_uninstaller“ (see picture). Follow the installation

instructions and finish the installation:

CHECK INSTALLED DRIVER

Open the > Device Manager Ports (COM & LPT) Multiple -<. Now you should see at „ “ and at „

Connection Adapter (serial) “ the following new entry‘s:

If you see this or a similar information the device is installed correctly.

CONNECTORS & JUMPERS

JP3 & JP5

You have the option of operating the EX-48210 in RS 422/485 4 wire or - -

RS 485 2 wire mode. For this purpose, you will find the following setting - -

options at jumper JP3 (COM1) & JP5 (COM2).

1/2 (Factory Setting) - -= RS 422/485 4 wire

3/4 - -= RS 485 2 wire

9 Pin Stecker Seriell

RS 485 2 Draht- -

Pin Signal Pin Signal

1 DATA 6 NC -

2 DATA+ 7 NC

3 NC 8 NC

4 NC 9 RI

5 GND

Produkt Specifikationer

Mærke:	EXSYS
Kategori:	Ikke kategoriseret
Model:	EX-48210

Har du brug for hjælp?

Hvis du har brug for hjælp til EXSYS EX-48210 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret EXSYS Manualer

EXSYS EX-44344 Manual

23 September 2025

EXSYS EX-44343 Manual

23 September 2025

EXSYS EX-45032IS Manual

24 Juli 2025

EXSYS EX-42034 Manual

24 Juli 2025

EXSYS EX-1311VIS Manual

24 Juli 2025

EXSYS EX-47925 Manual

24 Juli 2025

EXSYS EX-47200 Manual

23 Juli 2025

EXSYS EX-1305 Manual

23 Juli 2025

EXSYS EX-40032 Manual

23 Juli 2025

EXSYS EX-1332HMV Manual

23 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

RADEMACHER Troll Comfort-3D 5635 Manual

1 November 2025

Beverage-Air VueMax VMHC-7-1-B Manual

1 November 2025

SmallRig 4842 Manual

1 November 2025

Ikea TALGJE 702.982.38 Manual

1 November 2025

Lindy 43339 Manual

1 November 2025

Ikea VINTERFINT 805.800.24 Manual

1 November 2025

RADEMACHER RolloTron Schwenkwickler Comfort 1500 Manual

1 November 2025

Lantronix ION C2110 Manual

1 November 2025

Wiesenfield WIE-CHP-110 Manual

1 November 2025

Ikea KLOTTHUJA 105.506.76 Manual

1 November 2025