FLIR Zebra2 Manual

FLIR Ikke kategoriseret Zebra2

Læs gratis den danske manual til FLIR Zebra2 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 50 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 25.5 anmeldelser. Har du et spørgsmål om FLIR Zebra2, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
G
G
G
GGETTI
ETTI
ETTI
ETTIETTING
NG
NG
NGNG
STARTE
STARTE
STARTE
STARTESTARTED
D
D
DD
FLIR
ZEBRA®2
GigE
Vision
The Zebra2 is designed for use with both an HD-SDI interface and a GigEinterface.
Each interface can be installed and used independently.
Co
Co
Co
CoCon
n
n
nnnecti
necti
necti
nectinecting
ng
ng
ngng with
with
with
withwith HD-SD
HD-SD
HD-SD
HD-SDHD-SDI
I
I
II Co
Co
Co
CoCon
n
n
nnnecti
necti
necti
nectinecting
ng
ng
ngng with
with
with
withwith G
G
G
GGigE
igE
igE
igEigE
such as surveillance where no computer or control of the camera is
required.
The Zebra2 GigEinterface also allows for viewing video but also offers
camera control, image processing, and streaming to disk for applications
such as license plate recognition.
Pre
Pre
Pre
PrePrepari
pari
pari
pariparing
ng
ng
ngng for
for
for
forfor H
H
H
HHD-S
D-S
D-S
D-SD-SDI
DI
DI
DIDI Pre
Pre
Pre
PrePrepari
pari
pari
pariparing
ng
ng
ngng for
for
for
forfor Gi
Gi
Gi
GiGigE
gE
gE
gEgE
Before installation ensure you have the following:
nHD-SDI coaxial cable
nHD-SDI converter box
nHD-SDI interface, such as a monitor or TV
(HD-SDI ready devices do not require a converter box)
n4-pin Phoenix power terminal block
nCS-mount (or C-mount with adaptor) Lens
n6-pin Phoenix GPIOconnector for external device control
(optional—requires GigE connection for configuration)
nDownloads account to access firmware updates and documentation
Before installation ensure you have the following:
nEthernet cable
nNetwork adaptor card
nComputer: IntelCore 2 Duo, 2 GBRAM, PCIe 128 MB, Windows
Vista/7 or Linux Ubuntu 11.10
(or equivalent)
nPowered Ethernet switch or injector (if using PoE) or 4-pin Phoenix
power terminal block
nCS-mount (or C-mount with adaptor) lens
n6-pin Phoenix GPIOconnector for external device control
(optional)
nDownloads account to access software, firmware updates, and
documentation
nMicrosoft Visual Studio 2005 or 2010 (to compile and run example
code with FlyCapture SDK)
FLIR sells a number of the additional parts required for installation.
To purchase, visit our Accessories page.
FLIR sells a number of the additional parts required for installation.
To purchase, visit our Accessories page.
I
I
I
IIn
n
n
nnsta
sta
sta
stastall
ll
ll
llllin
in
in
ining
g
g
gg Yo
Yo
Yo
YoYou
u
u
uur
r
r
rr C
C
C
CCa
a
a
aam
m
m
mmera
era
era
eraera w
w
w
wwit
it
it
itith
h
h
hh HD-
HD-
HD-
HD-HD-SDI
SDI
SDI
SDISDI
1. Install the Tripod Mounting Bracket (optional)
The ASA and ISO- compliant tripod mounting bracket attaches to the
camera using the included screws.
2. Attach a Lens
Unscrew the dust cap from the CS-mount lens holder to install a lens.
Note: the camera can be used with a removable 5 mm C-mount adapter
and the back focus can be adjusted manually.
3. Connect the power
The 4-pin Phoenix power terminal block is used to power the camera.
4. Connect the HD-SDI cable
Plug the HD-SDI cable into the camera and the HD-SDI interface. HD-
SDI is always streaming and is available without user input after the
camera is started.
I
I
I
IIn
n
n
nnsta
sta
sta
stastall
ll
ll
llllin
in
in
ining
g
g
gg Yo
Yo
Yo
YoYou
u
u
uur
r
r
rr C
C
C
CCa
a
a
aam
m
m
mmera
era
era
eraera w
w
w
wwit
it
it
itith
h
h
hh G
G
G
GGig
ig
ig
igigE
E
E
EE
1. Install the Tripod Mounting Bracket (optional)
The ASA and ISO-compliant tripod mounting bracket attaches to the
camera using the included screws.
2. Attach a Lens
Unscrew the dust cap from the CS-mount lens holder to install a lens.
Note: the camera can be used with a removable 5 mm C-mount adapter
and the back focus can be adjusted manually.
3. Connect the power
If using PoE, connect a powered Ethernet switch or Ethernet power
injector in between the card and the camera. If not using PoE, plug in a 4-
pin Phoenix power terminal block.
4. Connect the Ethernet Cable
Plug the Ethernet cable into the camera. The cable jack screws can be
used for a secure connection.
Continue to Next Page for GPIO pin functions, mechanical properties,
and where to find more information.
Continue to Next Page for instructions on installing your network
adaptor card and software, GPIOpin functions, mechanical properties,
as well as where to find more information.
1/27/2017
Names and marks appearing on the products herein are either
registered trademarks or trademarks of FLIR Systems, Inc.
and/or its subsidiaries.
© 2012-2017 FLIR Integrated Imaging Solutions Inc. All rights
reserved.
Co
Co
Co
CoConn
nn
nn
nnnne
e
e
eecti
cti
cti
cticting
ng
ng
ngng the
the
the
thethe GPIO
GPIO
GPIO
GPIOGPIO
The camera is equipped with a 6-pin GPIO connector on the back of the
case and comes with a contact terminal for external device control. The
GPIO can be used for trigger, pulse width modulation, RS 485 serial
input output, and strobe.
GPIOfunctions can be used with either HD-SDI or GigE, however a
GigE connection is required for configuration.
Diagram Pin Function Description
1
OPTO IN (IO0) Opto-isolated input
2
OPTO GND Ground (opto-isolated pins)
3
OPTO OUT (IO2) Opto-isolated output
4
GND Ground
5
RS485B RS-485 Signal (inverting)
6
RS485A RS-485 Signal (non-inverting)
To configure the GPIOpins, consult the General Purpose
Input/Output section of the Technical Reference Manual.
Ze
Ze
Ze
ZeZebr
br
br
brbra2
a2
a2
a2a2 M
M
M
MMe
e
e
eechanic
chanic
chanic
chanicchanica
a
a
aal
l
l
ll Pr
Pr
Pr
PrPro
o
o
oopertie
pertie
pertie
pertieperties
s
s
ss
1. GPIO 4-pin connector
Phoenix 4-pin power terminal block.
2. GigEconnector
10/100/1000 BASE-TEthernet.
3. Auto Iris connector
DCDrive Auto Iris.
4. HD-SDI connector
5. Status LED
Indicates the current state of the
camera operation. (GigEonly)
6. GPIO6-pin connector
Phoenix GPIOfor Alarm/Event
trigger.
I
I
I
IInstal
nstal
nstal
nstalnstalling
ling
ling
lingling Y
Y
Y
YYo
o
o
oou
u
u
uur
r
r
rr N
N
N
NNe
e
e
eetwo
two
two
twotwork
rk
rk
rkrk A
A
A
AAd
d
d
dda
a
a
aapte
pte
pte
ptepter
r
r
rr Ca
Ca
Ca
CaCard
rd
rd
rdrd
a
a
a
aand
nd
nd
ndnd So
So
So
SoSof
f
f
fftware
tware
tware
twaretware (G
(G
(G
(G(GigE
igE
igE
igEigE o
o
o
oonly)
nly)
nly)
nly)nly)
1. Install your Interface Card
Ensure the card is installed per the manufacturer's instructions.
Open the Windows Device Manager. Ensure the card is properly
installed under Network Adaptors.
An exclamation point (!) next to the card indicates the driver has not yet
been installed.
2. Install the FlyCapture® Software
Note: We recommend having the latest FlyCapture version
installed.
a. Login to the downloads page.
b. Select from the drop-down list and click theZebra2 Search
button.
c. Click on the Software search results to expand the list.
d. Under , click the appropriate link to begin theFlyCapture v2x
download and installation.
After the download is complete, the FlyCapture setup wizard begins. If
the wizard does not start automatically, double- click the .exe file to
open it. Follow the steps in each setup dialog.
3. Enable the Drivers for the card
During the FlyCapture installation, you are prompted to select your
interface driver.
In the dialog, select theInterface Driver Selection I will use GigE
cameras.
Thisselection installs and enables the optional Image Filter driver.
Note: GigEVision cameras on Linux systems use native Ubuntu
drivers.
After installation is complete, the GigEConfigurator opens. This tool
allows you to configure the IPsettings of the camera and network
adaptor.
Ne
Ne
Ne
NeNeed
ed
ed
eded M
M
M
MMo
o
o
oor
r
r
rre
e
e
ee I
I
I
IIn
n
n
nnf
f
f
ffo
o
o
oorm
rm
rm
rmrma
a
a
aatio
tio
tio
tiotion
n
n
nn?
?
?
??
The Zebra2 Technical Reference is available from the Downloads site.
The Knowledge Base is available to answer many questions.
See also:Setting Up Multiple GigECameras TAN 10351 and Zebra2
and Compression TAN 10348
FlyCapture SDK help is in the All Programs>Point Grey
FlyCapture2 SDK>Documentation directory.
Co
Co
Co
CoContac
ntac
ntac
ntacntacting
ting
ting
tingting U
U
U
UUs
s
s
ss
For all general questions please contact us at mv-sales@flir.com.
For technical support (existing customers only) contact us at
www.ptgrey.com/support/ticket.
1/27/2017
Names and marks appearing onthe products herein are either
registered trademarks or trademarks of FLIR Systems, Inc.
and/or its subsidiaries.
© 2012-2017 FLIR Integrated Imaging Solutions Inc. All rights
reserved.

Produkt Specifikationer

Mærke: FLIR
Kategori: Ikke kategoriseret
Model: Zebra2

Har du brug for hjælp?

Hvis du har brug for hjælp til FLIR Zebra2 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret FLIR Manualer

FLIR

FLIR Tau SWIR Manual

8 September 2025
FLIR

FLIR Lepton Manual

8 September 2025
FLIR

FLIR Tau 2 Manual

7 September 2025
FLIR

FLIR Flea3 Manual

7 August 2025
FLIR

FLIR Blackfly S Manual

5 August 2025
FLIR

FLIR Forge Manual

5 August 2025
FLIR

FLIR Thermal Studio Manual

5 August 2025
FLIR

FLIR SkyWatch Manual

22 Juli 2025
FLIR

FLIR LS-X Manual

7 Juli 2025
FLIR

FLIR Horizon 9.3 Manual

11 Marts 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Brandson

Brandson 306618 Manual

15 September 2025
Daewoo

Daewoo AVS1412 Manual

14 September 2025
Neutrik

Neutrik NO4SBB2D-A Manual

14 September 2025
Invacare

Invacare Perfecto IRC5PO2AW Manual

14 September 2025
Neutrik

Neutrik NO12SABB3Q-A Manual

14 September 2025
JILONG

JILONG JL097205NPF Manual

14 September 2025
Brandson

Brandson 306570 Manual

14 September 2025
Nedis

Nedis PIM30012EGY Manual

14 September 2025
Neutrik

Neutrik SCD-W Manual

14 September 2025
BSS Audio

BSS Audio FCS-926 Manual

14 September 2025