Fluotec VegaLux 300 HP Manual

Fluotec Lys VegaLux 300 HP

Læs gratis den danske manual til Fluotec VegaLux 300 HP (2 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Fluotec VegaLux 300 HP, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
G6LED300 AC-POWERCON 3000K- 5600K ≥95 10 kg (22.2 lb)
G6LED127
8 LEAF BARNDOOR
G6FLT059
SAFETY CABLE (2)
G6LED128
GEL FRAME
G6FLT262
C-CLAMP
G6CNT154
AC CORD WITH
POWERCON CONECTOR
16 ft (4.82 m)
Most electrical equipment briefly draws a larger amount of electrical current during startup (ignition). Please refer to the chart to confirm that your
electrical wiring is sufficient for the units used. All fuses must be rated at 250VAC.
50.2 cm
19.76” 33.1cm
13.03”
45.3 cm
17.83” 31.2 cm
12.28”
The VegaLux 300 HP BICOLOR unit has a liquid crystal display to visualize its
functions.
MENU: Returns to the previous menu.
ENTER: Allows access to the selected menu and saves and confirms the
desired value.
UP: Allows navigation through the different menus and submenus.
Increases the selected value.
DOWN: Allows navigation through the different menus and submenus.
Decrements the selected value.
CCT: Rotate the knob left and/or right to modify the color temperature
value in a range of 300Ok-5600K. Press for fine adjustment. Press 2 times
quickly to select between 3000K-5600K.
DIM: Turn the knob left and/or right to modify the intensity value from 0 to
100%. Press for fine adjustment. Press 2 times quickly to select between
0%-100.
ZOOM: Turn the knob left and/or right to modify the angle of the light
beam from 25º to 55%. Press 2 times quickly to select between 25º-55º.
If there is no manipulation of the knobs and/or buttons for 1 minute, the
display screen will go into "standby".
5 A @ 250 VAC
346
90-240
2.89 A @ 120 VAC / 1.44 A @ 240 VAC
G6FLT057
STAND MOUNT SPIGOT
5/8”
The Vegalux 300 HP BICOLOR is a professional lighting system. Read these instructions, as well as any applicable accessory
instructions and warnings before operating the unit:
Do not leave the device unattended.
For fixed (stationary) use in studios, theaters, and similar places.
Not for home use.
Use for photographic lighting (TV, video, and film)
Always unplug the unit before changing the fuse.
Do not use near standing water.
Never remove the ground pin from the plug.
Do not interfere with the ventilation of the unit.
Do not operate the unit with barndoors closed.
Make sure the clamp is tight to the yoke.
Always use the safety cable when connecting to pipes or vents.
Always use it with the supplied AC cord.
Avoid looking directly at the luminaire (LED source).
1.- Do not operate this product if it is damaged.
2.- Avoid contact with water or other liquids to protect yourself from electric shock.
3.- You must turn the unit off before connecting it to the electrical network; also, when removing the unit from a grid or
tripod, turn it off before disconnecting it from an electrical network.
4.- In case of failure or malfunction, to avoid electric shocks, Do not disassemble the unit; call your FLUOTEC®
AUTHORIZED SERVICE CENTER.
Improper assembly or disassembly of this unit may cause a malfunction.
5.- Using accessories not designed or recommended by FLUOTEC® may cause dangerous conditions or damage the device.
Cleaning
CHASSIS.
Use a damp, almost dry cloth to remove dust and any stains.
NEVER USE ABRASIVE FIBER AND NEVER USE SOLVENTS; they can damage the appliance or its finish.
Repairs, problems, suggestions and requests for brochures, catalogs, illustrations and parts lists can be handled through
your authorized FLUOTEC® dealer or directly through FLUOTEC®. Electrical repairs must be carried out only by FLUOTEC®
or a qualified electrician.
FLUOTEC®
TEL. +1-213-296-4202
email : info@fluotec.com
Attach the clamp (C-clamp) firmly to the fixture's yoke, hang the clamp on the pipe or rack, and tighten the large screw so that
the clamp and fixture are securely mounted.
Do not loosen the screw that secures the clamp to the fixture to attach the light.
Connect the security cable between the ring and the grill rail to obtain the necessary security.
Use the 5/8" bracket accessory (not included), and choose an appropriate size tripod or bracket for the fixture.
Always use enough weight stabilizers (sandbags) at the base of the stand.
The 5/8" bracket accessory allows you to mount the fixture to a tripod or bracket with a 5/8" male stud (not included). Ensure the
tripod is large enough to support the fixture's weight while holding a good balance at the desired height. Hold the female
mounting fitting firmly to the yoke and tighten, hold the locking lever and place the 5/8" female fitting over the tripod, ensuring
its locking screw is loose enough to allow the fixture to fit through. completely over the 5/8" bolt of the bracket.
Tighten the knob, ensuring its screw is under the 5/8" bolt safety cutout on the fixture bracket. Add additional weight to the
tripod base or fixture bracket to increase stability.
1.- Confirm in the "Setting" menu that "Mode" is in "DMX".
2.- Confirm in the "Setting" menu that "Program" is "None".
3.- Check that the DMX controller is connected.
4.- Assign the desired DMX address.
1.- Disconnect the luminaire from the DMX controller.
2.- Select the "master" unit in the DMX chain through the configuration:
"Setting" ->" Mode" -> "M" and "progN” "Automatic operation".
3.- This mode is only compatible with similar products.
1.- Remove the DMX controller from the unit.
2.- Verify they unit is in "none" in "program" in the "setting"
menu.
3.- Press "ENTER" in the "CTRL" menu to enter the manual
configuration.
4.- In the DMX option press “ENTER” / “UP” / “DOWN”
to change the DMX address.
5.- Press "MENU" to exit the option to modify parameters.
6.- Repeat steps 4 and 5 with any other parameter you
wish to modify.
1.- Select the "Setting" menu and press "Enter".
2.- Through "Up" or "Down" select the desired option.
3.- Press "MENU" to return to the previous menu or exit.
1.- Select "ADDR," press "ENTER".
2.- Using "UP" and/or "DOWN," select the desired address.
3.- Press "MENU" to save the changes and return to
the previous menu.
1.- Select "Info" and press "ENTER", detailed system
information will be displayed:
DMX, M/S.
Standard / Reduced
None, Prog1, Prog2, Prog3
English
Normal / Inverted
ON / OFF
Square, Linear, I-Square, S-Shape,
Tungsten, Led effect
24KHz,18KHz,12KHz,6KHz,4.8KHz,3.6KHz,2.4KHz,
1.2KHz (Refreshment rate)
0-255
Press “ENTER”
********
0-99999
mm:ss
0-99 Hz
-55.0 - 125.0 ºC
rpm
MODE
CHANNEL VALUE FUNCTION
REDUCED STANDARD
1
1Dim 0~100%000-255
2
2Fine tuning Fine tuning DIM000-255
3
3CCT 000-255 CCT 3000~5600K
4
4Strobe
000-002 Open
003-127 1-20Hz
128-252 Random
253-255 Open
5 5 Zoom 000-255 25°~55°
\ 6 Dim Curve
000-063 Square
064-127 I-square
128-191 S-Shape
192-255 Lineal
\ 7 Dim Speed
000-127 Tungsten effect
128-255 LED effect
\ 8 Refreshment
000-031 24KHz
032-063 18KHz
064-095 12KHz
096-127 6KHz
128-159 4.8KHz
160-191 3.6KHz
192-223 2.4KHz
224-255 1.2KHz
9Fan Mode
000-010 None
011-064 Noiseless
065-096 Low speed
097-128 Automatic
129-255 Manual

Produkt Specifikationer

Mærke: Fluotec
Kategori: Lys
Model: VegaLux 300 HP

Har du brug for hjælp?

Hvis du har brug for hjælp til Fluotec VegaLux 300 HP stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys Fluotec Manualer

Fluotec

Fluotec VegaLux 300 HP Manual

2 Januar 2025

Lys Manualer

Nyeste Lys Manualer

LUPO

LUPO DayledPRO Full Color 311 Manual

9 Oktober 2025
Cateye

Cateye Nano F TL-LD830 Manual

9 Oktober 2025
IFootage

IFootage SL1 130BNA Manual

8 Oktober 2025
Caliber

Caliber HWL 1101 Manual

8 Oktober 2025
Westcott

Westcott Ice Light 3 Manual

8 Oktober 2025
Kichler

Kichler Eloise 43720PN Manual

8 Oktober 2025
IFootage

IFootage Anglerfish SL1 200BNA Manual

8 Oktober 2025
Godox

Godox Knowled P1200R Hard PRO Manual

8 Oktober 2025
Dracast

Dracast LED500 Pro Manual

8 Oktober 2025
VIJIM

VIJIM VL66 Manual

8 Oktober 2025