Focal FDP 1.900 Manual

Focal Modtager FDP 1.900

Læs gratis den danske manual til Focal FDP 1.900 (8 sider) i kategorien Modtager. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Focal FDP 1.900, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

POWER PER CHANNEL:

• 1 x 500 wRMS @ 4ohms

• 1 x 850 wRMS @ 2ohms

• 1 x 500 wRMS @ 1 ohms

• 1 x 1700 wRMS (Two FDP 1.900s Bridged @ 4 ohms only)

INPUT/OUTPUT CONFIGURATIONS

Because this is a one channel ampliﬁer, if both left and right inputs are used, they are mixed to mono, which is useful

for subwoofers.

CROSSOVER CONFIGURATION

The 24 dB per octave crossover can be adjusted so this ampliﬁer can function as:

1. Full range

2. Low Pass for a subwoofer.

3. Band Pass for a subwoofer or midbass of a 3 way speaker.v

4. High Pass for a midbass, midrange or tweeter.

• The amplifier can be used full range with switch in HP position and frequency set to 10 Hz.

HP is always on so it can be used as a subsonic filter.

HP X1 frequency range is 10 Hz to 400 Hz.

HP X10 frequency range is 100 Hz to 4000 Hz.

LP: Adjustment range is 30 Hz to 350 Hz.

Band Pass with switch in LP position and adjusting both HP and LP to desired frequency.

• The remote volume control is always active.

There is a clip distortion light on the remote volume control.

If you see this light on, reduce volume until the light goes out so that you do not damage your speaker.

• Phase is continuously adjustable between 0 degrees and 180 degrees. Adjust by measuring frequency response

at the crossover frequency. Frequency response should be as smooth as possible.

• 40 Hz EQ is adjustable between 0dB and +6dB.

Measure the subwoofer frequency response and adjust EQ to get the smoothest frequency response.

Avoid excess EQ boost because this will make the subwoofer sound “muddy” and cause the amplifier have clip

distortion prematurely.

AUTOMATIC POWER TURN ON/OFF

1. The best way to automatically turn the amplifier power on and off is to use the REM wire from your source radio

connected to the REM amplifier terminal.

2. If your original equipment stereo or source radio has a BTL amplifier then the RCA inputs have an auto turn

on sensing circuit. When you connect the high level BTL speaker wires to the RCA input the REM wire is not

necessary.

FDP 1.900 : ONE CHANNEL AMPLIFIER

Operation / Configuration

RCA INPUT, BOTH LOW LEVEL AND HIGH LEVEL.

The ampliﬁer control has sufﬁcient adjustment range for both low level and high level input into the RCA LEVEL

jacks. A factory source radio that does not have RCA output, using the wires that are connected to the speakers, can be

directly connected to the RCA jacks when the ampliﬁer control is adjusted to 8V.LEVEL

SETTING LEVEL

• Set the amplifier control to minimum before you turn on the amplifier for the first time.LEVEL

• For lowest distortion and lowest noise the ampliﬁer should be set at the lowest setting that yields LEVEL

sufﬁcient loudness without distortion. For lowest noise your source radio volume control should be near

maximum that does not cause distortion.

• To ﬁnd the best ampliﬁer setting: LEVEL

With the ampliﬁer at minimum, slowly increase the source radio volume to around 3/4 without distortion. LEVEL

Then, slowly turn up the ampliﬁer control to the maximum desired loudness. Listen very carefully and LEVEL

turn down the ampliﬁer control if you hear any distortion.LEVEL

SETTING SUBWOOFER HIGH PASS SUBSONIC FILTER:

• A subwoofer should have a high pass filter often called a subsonic filter. The purpose of a subsonic filter is to

limit very low frequencies that your subwoofer can not play loud enough without damage. Removing subsonic

frequencies can allow your subwoofer to play louder.

• For a sealed box the high pass is typically set between 10 Hz and 30 Hz to increase power handling capacity.

• For a vented box the high pass ﬁlter must be set 5 Hz lower than the port tune frequency to prevent woofer

damage.

Produkt Specifikationer

Mærke:	Focal
Kategori:	Modtager
Model:	FDP 1.900

Har du brug for hjælp?

Hvis du har brug for hjælp til Focal FDP 1.900 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Modtager Focal Manualer

Focal FDP 1.900V2 Manual

28 August 2024

Focal FPX 1.100 Manual

21 August 2024

Focal FPS 4160 Manual

21 August 2024

Focal FDP 6.900 Manual

20 August 2024

Focal FDP 6.900 V2 Manual

19 August 2024

Focal FDS 2.350 Manual

19 August 2024

Focal FPS 2160 Manual

19 August 2024

Focal FDP 4.600 Manual

19 August 2024

Focal FDP 1.2000 Manual

19 August 2024

Focal FDS 1.350 Manual

19 August 2024

Modtager Manualer

Nyeste Modtager Manualer

Albrecht HAE75 Manual

1 August 2025

CYP AU-A220 Manual

30 Juli 2025

Sirus I-Amp 8.150T Manual

30 Juli 2025

AER Colourizer 2 Manual

30 Juli 2025

Sirus I-Amp 1.300T Manual

30 Juli 2025

PAC AP4-FD32 Manual

30 Juli 2025

CYP PUV-1540S-RX Manual

30 Juli 2025

ART USB Dual Pre Manual

29 Juli 2025

SSL Pure Drive Quad Manual

29 Juli 2025

SSL Pure Drive Octo Manual

29 Juli 2025