Fredrick Ramond FR45601BNI Manual

Fredrick Ramond Lys FR45601BNI

Læs gratis den danske manual til Fredrick Ramond FR45601BNI (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 43 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 22 anmeldelser. Har du et spørgsmål om Fredrick Ramond FR45601BNI, eller vil du spørge andre brugere om produktet?

Side 1/3
FR45601BNI/FBZ
MIME
ASSEMBLY I N STR UC TIONS
Assembly of this fixture will be accomplished by first assembling the main body,
installing the mounting hardware to the junction box, hanging the fixture and then
installing the shade and crystals.
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1
STEP 2 Refer to Hanging Instruction Sheet to hang fixture. Then refer[FRIS19-41 ]
back to this sheet to continue installation of this fixture.
STEP 3
1
2
3
[DRAWING 1]
Bulbs: 3-60W CAND. Replacement Parts: SHADE: R45601SH (BNI FINISH),
R455601AMBSH ( fbz FINISH),
R45602CRY-A
01.01.13
3d
ce
1b
e
4
2
5
After unpacking fixture main body can be installed prior to attaching the shade.
Take shade and line up holes in tabs with the holes in (1) (d)
end of arms . Shade tab shold be on top of the arm -see . (b) Drawing 1
Slip flat head screw (2) through hole in arm and hole in shade
tab. Thread barrel knob onto end of screw to secure shade.(3) (2)
Repeat process with the remaining arms.
Thread finial (4) onto threaded tube (t) found at the bottom of the fixture.
Attach crystals (5) at point (e) as indicated in .Drawing 1
e
5
t
4
HA GI NSTN NG I RUCT NSIO
FRIS19 41-
SA Y FET WA NG:RNI Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
EP 1ST
1 Shut off electrical current before starting. If the fixture you are replacing is
turned on and off by a wall switch, simply turn the switch off. If not, remove the
appropriate fuse (or open the circuit breakers) until the fixture is dead.
N• DO OT restore current - either by fuse, breaker or switch - until the new
fixture is completely wired and in place.
EP 2ST
[DRA N ]WI G 2
01.01.13
3
4
1 Prepare mounting strap (a) by threading screws (b) into appropriately threaded hole
(h) - see Drawing 1. Make sure spacing of screws matches spacing of mounting holes
(3) in Canopy (c) -see Drawing 2.
2 Install mounting strap (a) to junction box (j), with two 8-32 screws (1) - see Drawing 2.
1 To mount fixture to ceiling , slip screws (b) in mounting strap (a) through
holes (3) in canopy (c) - see Drawing 2.
2 Hold canopy (c) up to ceiling and thread deocrative knobs (4) onto end of
screws (b) and tighten to secure fixture to ceiling.
3 Return to previous instruction sheet to complete fixture assembly.
c
[DRA N ]WI G 1
EP 3ST
Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet and follow all instructions to make all necessary [FRIS18]
wiring connections. Then refer back to this sheet to continue installation of
this fixture.
EPST 4
a
1
b
a
j
b


Produkt Specifikationer

Mærke: Fredrick Ramond
Kategori: Lys
Model: FR45601BNI

Har du brug for hjælp?

Hvis du har brug for hjælp til Fredrick Ramond FR45601BNI stil et spørgsmål nedenfor, og andre brugere vil svare dig