Fredrick Ramond FR45608BNI Manual

Fredrick Ramond Lys FR45608BNI

Læs gratis den danske manual til Fredrick Ramond FR45608BNI (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 57 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 29 anmeldelser. Har du et spørgsmål om Fredrick Ramond FR45608BNI, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/3
FR45608BNI/FBZ
MIME
ASSEMBLY I N STR UC TIONS
Assembly of this fixture will be accomplished by first assembling the main body,
installing the mounting hardware to the junction box, hanging the fixture and then
installing the shade and crystals.
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
1
STEP 2 Refer to Hanging Instruction Sheet to hang fixture. Then refer[FRIS19]
back to this sheet to continue installation of this fixture.
STEP 3
1
2
3
[DRAWING 1]
Bulbs: 6-60W CAND. Replacement Parts: SHADE:
11.23.09
Slip center stem with top main body along wire and thread onto threaded(4) (b)
tube located on the top of socket body assembly .(t) (a)
Slip loop along wire and thread onto top of fixture.(5)
Spread arms until they are 60 degrees apar t.(b)
Fixture is ready for installation.
2
3
4
Take shade and line up holes in tabs with the holes in (7) (d)
end of arms . Shade tab shold be on top of the arm. (b)
1Slip center col
main body with the three arms see (b) - DRAWING 1.
umn
(4) along wire and thread onto swivel (s) located on the top
: R45608SH (BNI FINISH),
R455608AMBSH ( fbz FINISH),
R45602CRY-A
Slip ball knob stud through hole in shade tab and thread it into (8)
arm . Repeat process with the remaining shade tabs. (b)
attach crystals to loop (9) (e).
Next thread knob onto threaded tube . Then(10) (f)
4
8
d
ce
5
b
e
e
9
7
9
t
a
f
10
HANGING INSTRUCTIONS
FRIS19
SAFETY WARNING: Read wiring and grounding instructions [FRIS 18]
and any additional directions. Turn power supply off during installation. If new wiring
is required, consult a qualified electrician or local authorities for code requirements.
STEP 1
Shut off electrical current before starting. If the fixture you are replacing is1
turned on and off by a wall switch, simply turn the switch off. If not, remove the
appropriate fuse (or open the circut breakers) until the fixture is dead.
• DO NOT restore current - either by fuse, breaker or switch - until the new
fixture is completely wired and in place.
STEP 2
STEP 3
Taking the chain, determine the length you require to hang the fixture.1
Attach one end of the chain to the top loop of the fixture - see .2 Drawing 2
Now slip loop collar and canopy onto chain .3 (6) (B) (C)
4 Attach other end of chain to loop . Get assistance for this step since fixture (5)
may be heavy and difficult to hold while attaching the chain.
STEP 4
1 Unwrap supply wire and ground wire and weave them up through the chain.
Slip supply wire and ground wire through center of loop2 (5).
Connect ground wire to mounting strap using green ground screw .3 (1) (GS)
4 Make electrical connections from supply wire to fixture lead wires. Refer to
instruction sheet and follow all instructions to make all necessary [FRIS18]
wiring connections.
Slip canopy up firmly against the ceiling and secure by turning the threaded 5
loop collar onto loop until tight.(6) (5)
[DRAWING 1]
[DRAWING 2]
1
2
A
4
B5
C
6
weave supply wire and
ground wire through chain
GS
3c
3b
3a
half of threaded area
exposed
1 Fasten mounting strap to outlet box with the two 8-32 screws (not provide) (1) (A)
(2) Drawing 1. -see
2 (3a) (3b) (4) Thread 2 - hex nuts and onto threaded tubing .
3 (4) (5) Thread one end of threaded tubing into loop a minimum of 1/2” to 3/4”.
Thighten hexnut against loop to lock loop in position.(3a) (5)
4 (4) Thread other end of threaded tube into mounting strap approximately 1/2”.
5 (B) (5) Slip canopy over loop and adjust height of loop so half of the threaded area
on the loop is exposed - see below. After loop height is adjusted, thigtenDrawing 2
hex nut up against mounting strap, tighten against mounting strap to lock (3b)
in position.
6 (1) (A) (3c) Remove mounting strap from junction box , and thread third hex nut onto
end of threaded tube above the mounting strap , tighten against mounting strap (4), (1)
to lock assembly in position.
7 Remount mounting strap to junction box.
021714

Produkt Specifikationer

Mærke: Fredrick Ramond
Kategori: Lys
Model: FR45608BNI

Har du brug for hjælp?

Hvis du har brug for hjælp til Fredrick Ramond FR45608BNI stil et spørgsmål nedenfor, og andre brugere vil svare dig


Lys Fredrick Ramond Manualer

Fredrick Ramond

Fredrick Ramond FR45601BNI Manual

2 September 2024
Fredrick Ramond

Fredrick Ramond FR45608BNI Manual

2 September 2024

Lys Manualer

Nyeste Lys Manualer

LUPO

LUPO DayledPRO Full Color 311 Manual

9 Oktober 2025
Cateye

Cateye Nano F TL-LD830 Manual

9 Oktober 2025
IFootage

IFootage SL1 130BNA Manual

8 Oktober 2025
Caliber

Caliber HWL 1101 Manual

8 Oktober 2025
Westcott

Westcott Ice Light 3 Manual

8 Oktober 2025
Kichler

Kichler Eloise 43720PN Manual

8 Oktober 2025
IFootage

IFootage Anglerfish SL1 200BNA Manual

8 Oktober 2025
Godox

Godox Knowled P1200R Hard PRO Manual

8 Oktober 2025
Dracast

Dracast LED500 Pro Manual

8 Oktober 2025
VIJIM

VIJIM VL66 Manual

8 Oktober 2025