GE GNWH38S Manual

GE Vandfilter GNWH38S

Læs gratis den danske manual til GE GNWH38S (8 sider) i kategorien Vandfilter. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 6 anmeldelser. Har du et spørgsmål om GE GNWH38S, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

REQUIRED TOOLS AND ACCESSORIES FOR INSTALLATION

■2 Adjustable wrenches

■Pipe cutter

■Ruler or tape measure

■Cordless drill

■File

■Emery paper

■Screwdriver

Optional accessories are available (Visa, MasterCard or Discover cards accepted)

by visiting our Website at www.GEAppliances.com or from Parts and Accessories,

call 800.626.2002 (U.S.) or 800.663.6060 (Canada).

CONTENTS INCLUDED WITH PRODUCT

■Filter system (head and canister)

■Product literature

■Canister wrench

■Timer and batteries

■Mounting bracket

■Four 5/16″ Hex-head screws and four 5/16″Hex washer-head

screws

■2 sets of fitting, ferrule, and nut

■2 UL-approved grounding clamps and a #6 AWG grounding

wire

■White sealing tape

GE Smar tWater ™

INSTALLATION INSTRUCTIONS

Heavy Duty Water Filtration System—GNWH38F

SAFETY PRECAUTIONS

■Check with your state and local public works department for

plumbing and sanitation codes. You must follow these guidelines

as you install the Heavy Duty Water Filtration System. Using a

qualified installer is recommended.

■Be sure the water supply conforms with the Performance Data.

If the water supply conditions are unknown, contact your

municipal water company.

WARNING: Do not use with water that is

microbiologically unsafe or of unknown quality without

adequate disinfection before or after the system.

■It is highly recommended that a water shut-off valve be placed

directly upstream of your household filter.

■Check with your local public works department for plumbing codes.

You must follow their guides as you install the Heavy Duty Water

Filtration System.

■Use the Heavy Duty Water Filtration System on a potable, safe-to-

drink, home COLD water supply only. The filter cartridge will not

purify water or make unsafe water safe to drink. DO NOT use on

HOT water (100 F max).°

■Protect the Heavy Duty Water Filtration System and piping from

freezing. Water freezing in the system will damage it.

■Your Heavy Duty Water Filtration System will withstand up to

100 psi water pressure. If your house water supply pressure is

higher than 100 psi during the day (it may reach higher levels

at night), install a pressure reducing valve before the system

is installed.

■Do not install on HOT WATER. The temperature of the water

supply to the Heavy Duty Water Filtration System must be

between the minimum of 40°F and the maximum of 100°F.

See the Filter Cartridge Life section.

■Do not install the Heavy Duty Water Filtration System using

copper solder fittings. The heat from the soldering process

will damage the unit.

■If making a soldered copper installation, do all sweat soldering

before connecting pipes to the system. Torch heat will damage

plastic parts.

WARNING: Discard all unused parts and packaging

material after installation. Small parts remaining after installation

could be a choke hazard.

■Do not install filter in an outside location or anywhere it will be

exposed to sunlight.

PROPER INSTALLATION

This Heavy Duty Water Filtration System must be properly installed and located in accordance with the Installation Instructions

before it is used.

GNWH38F is

Tested and Certified by NSF International

against NSF/ANSI

Standard 42 for materials and

structural integrity requirements only.

184D1064P001 (04--04 JR) 49-50125

www.GEAppliances.com

GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225

COMPONENT

GNWH38F is tested and certified by NSF International

against NSF/ANSI Standard 42 with cartridge FXHTC

for the reduction of Chlorine: Taste and Odor.

Filter Cartridge Replacement

You should change your filter when the water flow is noticeably reduced or at least every 3 months.

Turn off water to filter. Water must be shut off from

an upstream valve.

Press the red pressure release button to release

pressure.

Unscrew the filter canister and discard used filter.

Wash the filter canister with mild soap and water.

Do not use harsh cleaners or hot water.

Inspect the filter canister O-ring. Make sure it is

lightly lubricated with clean food grade silicone

grease (silicone grease is available through GE

Parts and Service: 1.800.626.2002, part number

WS60X10005). Be sure the o-ring is seated in the

groove. It is recommended that you replace the

O-ring if it is damaged.

Place a new filter cartridge into the canister,

making sure it is centered and completely seated

on the bottom seal.

Reinstall the filter canister to the unit. Use the

canister wrench to tighten the canister. DO NOT

OVERTIGHTEN.

Slowly turn on water to the filter by using the

upstream shut-off valve.

Press the red pressure release button to remove

trapped air.

After installation, flush the cartridge for

10 minutes, wait one hour, then flush again

for 10 minutes before using the water.

Installation Overview

NOTE: Be sure to allow a minimum space of 11⁄ –2 under2″ ″

the filter for removing the sump to change the cartridge.

Turn canister wrench

clockwise to remove

Canister

Turn

clockwise

to remove

canister

Turn

counterclockwise

to tighten

Red pressure

release button

Filter

cartridge O-ring seal

Filter canister

Head

STEP-BY-STEP INSTALLATION INSTRUCTIONS

Recommended

shut-off valve

Recommended

shut-off valve

Fitting

Ferrule

Hex nut

Fitting

Ferrule

Hex nut

11⁄2″–2″

Typical installation

Remote timer

Mounting

bracket

CARTRIDGE SPECIFICATIONS

Influent Challenge Reduction Average

Substance Concentration Requirements Reduction

Standard 42

Chlorine: Taste and Odor 2.0 mg/L ± ≥10% 50% 95.5%

Performance Data

This system has been tested according to NSF/ANSI 42

for the reduction of the substances listed below. The

concentration of the indicated substances in water

entering the system was reduced to a concentration

less than or equal to the permissible limit for water

leaving the system, as specified in NSF/ANSI 42.

FXHTC Cartridge

Test Conditions

Flow Rate: 3 gpm (11.4 Lpm)

pH: 7.5 ±1

Inlet Pressure: 60 PSI (4.1 bar)

Temperature: 68°F ± 5°F (19.8°C ± 2.5°C)

Operating Requirements

Pressure: 30–125 psi (2.1–6.9 bar)

Turbidity: 5 NTU Max.

Temperature: 40°F–100°F (4.4°C–37.7°C)

Capacity: 5,000 gallons (18,927L) or 3 months

Testing was performed under standard laboratory conditions, actual performance may vary.

GE Model Function Life Construction

FXHSC Sediment* 3 months/ Pleated

30 Micron* 24,000 gallons

Additional Replacement Filter

FXHSC Filter could be used as a replacement filter.

FXHSC Cartridge

Operating Guidelines

Minimum–Maximum Supply Water Pressure: 20–125 psi

Minimum–Maximum Supply Water Temperatures: 40°F–100°F

*Based on manufacturer’s internal testing.

Produkt Specifikationer

Mærke:	GE
Kategori:	Vandfilter
Model:	GNWH38S

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GNWH38S stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vandfilter GE Manualer

GE GXRLQK Manual

21 Februar 2025

GE Profile PNRQ15RBL Manual

9 December 2024

GE GX1S15C Manual

13 Oktober 2024

GE GXSF18G Manual

2 September 2024

GE Profile PNRQ20FBB Manual

2 August 2024

GE GX1S01C Manual

2 August 2024

GE GNWH38S Manual

31 Juli 2024

GE Profile PXCR33KSSDM Manual

29 Juli 2024

GE GXCF03KWW Manual

25 Juli 2024

GE Profile PXCR33KSS Manual

25 Juli 2024

Vandfilter Manualer

Nyeste Vandfilter Manualer

Hendi 231234 Manual

10 August 2025

Breville the Chill Control BWC200 Manual

9 August 2025

Philips AWP2941 Manual

6 August 2025

6 August 2025

5 August 2025

5 August 2025

4 August 2025

Bestway Flowclear 58774 Manual

4 August 2025

Haier HP16 Manual

27 Juli 2025

Haier HU612-4G Manual

27 Juli 2025