GE GXRV10ABL Manual

GE Vandfilter GXRV10ABL

Læs gratis den danske manual til GE GXRV10ABL (6 sider) i kategorien Vandfilter. Denne vejledning er vurderet som hjælpsom af 47 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 24 anmeldelser. Har du et spørgsmål om GE GXRV10ABL, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

■ Use pipe thread-sealing tape (provided) on threaded

connections.

■ Tubing may be cut to desired length.

■ When connecting the kit to a refrigerator water dispenser,

a slightly lower dispenser water pressure may be noticed.

This is normal.

■ It is normal for the GREEN light to flash on the faucet monitor

when the icemaker or dispenser calls for water (on some

models).

■ Before installing the icemaker kit, install the Reverse Osmosis

Filtration System according to the installation instructions.

INSTALLATION NOTES

Fig. 1

To drain

point

RO water faucet

(lift lever to open)

Water supply

valve

GE SmartWater

Water Filtration System Icemaker Connection Kit (RVKIT)

INSTALLATION INSTRUCTIONS

For use with models GXRV10, GXRM10, PNRQ15, PNRQ20,

PNRV12 (beginning on page 1) and PNRV18 (beginning on page 4)

215C1044P031 (11-04 JR) 49-50138

www.GEAppliances.com

GENERAL ELECTRIC COMPANY, Appliance Park, Louisville, KY 40225

1. Turn off the icemaker.

2. Turn off the water supply to the Reverse Osmosis Filtration

System by closing the water supply valve (Fig. 1).

3. Drain the RO system and tank. Turn on the RO faucet located

on the sink or countertop (Fig. 1). Let the water drain from the

system until water has stopped flowing. On models equipped

with a tank shutoff valve, make sure the valve is open so that the

tank will drain. Close the RO faucet.

4. Cut the 3/8″tubing that connects the storage tank to the RO

system (Fig. 2); this tubing will be either orange, gray or white,

depending on model. Make sure the cut is clean and straight

with no burrs or crimps. Insert on Tee fitting between the two

cut ends of the tubing (Fig. 2). Push the tubing into the fitting

until it stops—about 1/2″. Give tubing a tug to make sure it is

seated securely.

5. Connect the tank to the Tee using the 6 ft. length orange

tubing.

CONNECTING THE AUXILIARY TANK—FOR MODELS GXRV10, GXRM10, PNRQ15, PNRQ20, PNRV12

■ Storage tank

■ Tank adapter

■6 ft. 3/8″orange tubing

■ 2 Tee fittings with

push-to-connect ends

■ Brass tubing adapter, nut and

washer assembly

■33 ft. 3/8″blue tubing

■ Pipe thread tape

■1 ft. 3/8″orange tubing

KIT CONTENTS

■ Utility knife

■ Pliers and adjustable jaw wrench

TOOLS AND MATERIALS REQUIRED

ColdHot

Fig. 2

Storage tank

Orange tubing

Auxiliary

storage tank

(included

with RVKIT)

Tee fitting

Nut

Tubing

Reverse Osmosis

system

Cut

From water

supply valve

Tee

Tank shutoff valve

Storage tank

Electronics box

(on some models)

Fig. 3

This tubing adapter can be used

on most icemakers. Obtain needed

fitting for others.

Fig. 4

To drain

point

RO water

faucet

Cut

icemaker

Insert

Tee

fitting

Nut

Tubing

1. Locate the 3/8″tubing that supplies the product water to the

RO faucet. It will be blue, gray or white, depending on the

model. Do not confuse the product water tubing with the drain

water tubing that also goes to the faucet (black or white on most

models). At a convenient point between the faucet and the

electronics box (on some models), cut the tubing and install

the second Tee fitting. Connect one end of the 33-foot length

of blue tubing as shown in Fig. 4.

2. Turn off icemaker water supply. Disconnect the water source

tubing from the refrigerator.

3. Connect the brass tubing adapter to the free end of the

33-foot length of blue tubing. Shorten tubing to desired length.

Attach the other end of the adapter to the icemaker water

valve. Be sure to install the plastic washer into the tubing

adapter as shown in Fig. 5.

CONNECTING TO THE ICEMAKER—FOR MODELS GXRV10, GXRM10, PNRV12

See your Reverse Osmosis System Owner’s Manual for complete

Sanitization Instructions.

1. Remove the sumps. Remove the filters and place in a clean

plastic bag. If it has been six months since you last replaced

filters, go ahead and discard them and replace with new filters.

2. Thoroughly wash sumps with dish soap. Thoroughly wipe

inside of head with a paper towel moistened with dish soap.

Rinse well.

3. Remove cap from RO cartridge housing. Remove the RO

cartridge and place in a clean plastic bag. Thoroughly wipe

inside the housing and cap with a paper towel or dish brush

moistened with dish soap. Rinse well.

4. Replace empty postfilter sump and RO housing cap.

5. Fill prefilter sump with water to within 1″of o-ring. Add 2 oz.

(4 Tbsp.) of ordinary household bleach. Replace prefilter

sump.

6. Make sure both tanks are sitting at the same elevation.

Otherwise, the higher tank may not be sanitized properly. Turn

on water supply. Open RO faucet until water begins to flow,

then close. Allow system to fill for one minute.

7. Open the faucet and allow water to flow for 10 minutes. Close

faucet for one minute more, then open and allow water to flow

for another 10 minutes, or until the bleach odor is gone. Turn

off water supply again. Drain RO system.

8. Remove sumps. Insert filters. Lubricate o-ring with food-grade

silicone grease, if necessary. Do not use petroleum jelly. Tighten

sumps securely.

9. Remove cap from RO cartridge housing. Install RO cartridge,

o-ring end first. Lubricate cover o-ring with food-grade silicone

grease, if necessary. Do not use petroleum jelly. Tighten cap

securely.

10. Turn on water supply. Allow to fill. It may take 4–8 hours to fill

both tanks. Check for leaks.

11. If you replace the prefilter and postfilter, allow faucet to run a

few minutes to remove harmless carbon particles.

12. Once storage tanks are full, turn on icemaker. If you have a

concern that some of the bleach water may have backwashed

into the icemaker inlet lines, discard the first two batches of

ice. Or, drain your dispenser tank until water no longer runs

cold, and check for bleach taste and odor.

SANITIZING THE SYSTEM—FOR MODELS GXRV10, GXRM10, PNRV12

Secondary storage tank

(included with RVKIT)

Tank shutoff valve

(on some models)

Product

water tube

Fig. 5

Plastic

washer

Icemaker

water valve

Brass tubing

adapter

3/8″tubing

Nut

Produkt Specifikationer

Mærke:	GE
Kategori:	Vandfilter
Model:	GXRV10ABL

Har du brug for hjælp?

Hvis du har brug for hjælp til GE GXRV10ABL stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vandfilter GE Manualer

GE GXRLQK Manual

21 Februar 2025

GE Profile PNRQ15RBL Manual

9 December 2024

GE GX1S15C Manual

13 Oktober 2024

GE GXSF18G Manual

2 September 2024

GE Profile PNRQ20FBB Manual

2 August 2024

GE GX1S01C Manual

2 August 2024

GE GNWH38S Manual

31 Juli 2024

GE Profile PXCR33KSSDM Manual

29 Juli 2024

GE GXCF03KWW Manual

25 Juli 2024

GE Profile PXCR33KSS Manual

25 Juli 2024

Vandfilter Manualer

Nyeste Vandfilter Manualer

Manitowoc AR-40000-P Manual

15 Juni 2025

Manitowoc AR-20000-P Manual

15 Juni 2025

Scotsman SSM2-P Manual

14 Juni 2025

Scotsman SSM3-P Manual

14 Juni 2025

Emga 340001 Manual

31 Marts 2025

Everpure H-1200 Manual

21 Februar 2025

Philips AWP1812 Manual

7 Februar 2025

Oase AquaSkim 20 Manual

3 Februar 2025

Seagull IV X-1F Manual

16 Januar 2025

AstralPool Oslo Manual

11 Januar 2025