Gira 5533920 Manual

Gira Intercomsystem 5533920

Læs gratis den danske manual til Gira 5533920 (2 sider) i kategorien Intercomsystem. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Gira 5533920, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

General safety instructions

These instructions are part of the product

and must remain with the end customer.

Necessary accessories

• System 106 intercom module (item no.

5555 ..) or door station module (item

no..5565 ..).

• Audio control device (item no. 1287 00).

• Gira home station.

• System 106 surface-mounted housing,

1-gang to 5-gang.

Accessories

• System 106 camera module (item no.

5561 00).

• Video control device (item no. 1288 00) if

using a camera module

• Call-button cover plate for call-button

module (item no. 5541 9xx).

• Start-up key for call-button module (item

no. 5539 00)

Functional description

The call-button module covers the functions

“door call” and “switch” in the Gira door

communication System 106.

Scope of supply

1 x System 106 call-button module

1 x operating instructions

1 x tool for inscription label

Ensure the package contents are complete

and undamaged. When filing complaints,

see "Warranty".

Electrical devices may only be

installed and connected by a

qualified electrician.

Device description

Front view

Rear view

Installing the module

Starting up the device

The call-button module can only be started

up with an intercom or door station module

with a control device (see “Assigning call

buttons”).

All devices (System 106 module, home

stations, control devices etc.) must be

installed to successful start-up.previous

1 Module

2 Call button

3 Inscription label

1 Threaded hole for mounting screw

2 Turn-type lock (4 x)

3 Fastening screw for call button (non-

removable)

4 Slot (2x): System cable

Installing the module

The installation instructions for the

System 106 surface-mounted 1-gang to 5-

gang housing describes the following

working steps:

• Lock the module on the mounting

frame.

• Plug in the connection cable.

• Place terminating resistors.

Terminating resistor

From the 2-gang surface-mounted housing

up, there are always two terminating

resistors included.

The terminating resistors are always

connected to the first and last module on

the system cable.

Configuring the module

Assigning call buttons

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. Call-button module: Press the buttons in

the sequence in which the home

stations are to be assigned 3 seconds

each.

3. First call button: A brief

acknowledgement tone can be heard

after 3 s: Release the call button. Then a

long acknowledgement tone sounds.

Repeat step 3 for all other call buttons

than need to be assigned.

4. First home station: Press button for

about 3 s. Release the button after the

first brief acknowledgement tone .

Then a long acknowledgement tone

sounds. The call button has been

assigned to the home station

successfully.

5. Repeat step 4 for all other home

stations.

6. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Setting the speaker volume

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. : Briefly press the Door station module

already assigned call button.

3. : Accept call and start Home station

voice communication.

4. : Briefly press call Door station module

button again.

Volume control: Press the button during

voice communication to adjust volume

(total of five volume levels;

level 4 is preset). Each press of the call

button increases the volume by one

level. (After the highest volume level, the

system cycles to the lowest level.)

5. : End voice Home station

communication. The most recent volume

level is stored in the door station.

6. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Teaching sequence

Always teach the switching actions first, then

the call buttons.

Optical and acoustic status feedback

via the intercom module

While the programming mode is active, the

intercom module gives the following visual

and acoustic feedback:

• Programming mode started: LED flashes

orange.

• Programming via the call button: Every

3 s, a short acoustic acknowledgement

sounds and the LED flashes green.

• Programming finished: A long acoustic

acknowledgement sound can be heard,

and the LED lights up green.

• Programming mode cancelled: LED goes

out.

Deactivating/activating the acoustic

call button actuation

Acoustic call button actuation is

deactivated by default and is activated

automatically for each assigned call button.

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. : Press and hold any Call-button module

call button for 6 s.

Release the call button after the second

brief acknowledgement tone (= 6 s).

Then a long acknowledgement tone

sounds to indicated that the acoustic

call button actuation is deactivated for

all call buttons.

3. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Reactivation: Repeat steps 1 to 3.

Backlight

The backlight can be turned on and off for

each call button individually or for all call

buttons collectively.

Switching off the backlight for single

buttons

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. : Press and hold any Call-button module

call button for 9 s. Release the call

button after the third brief

acknowledgement tone (= 9 s). Then a

long acknowledgement tone sounds and

all backlit call buttons are visible. Press

any call button again: The backlight is

switched off for all call buttons of the

module.

3. : Briefly press (no Single call button

acknowledgement tone!) to turn the

backlight back on. Repeat this step for

all call buttons that you would like to be

backlit.

4. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Switching off the backlight for all buttons

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. : Press and hold a Call-button module

call button for 12 s. Release the call

button after the fourth brief

acknowledgement tone (= 12 s). Then a

long acknowledgement tone sounds.

The backlight is switched off completely.

3. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Turning the backlight back on: Repeat

steps 1 to 3.

Automatic backlight

When the backlight is active, then the

backlight can be switched on and off

automatically depending on the ambient

light via the voice or door station module.

The backlight is activated by default.

Operating the module

Door call

1. Press the call button to trigger a door

call at the assigned home station. The

button actuation can be confirmed

acoustically (acknowledgement tone) or

visually (backlight).

Light switching (requires switching

actuator)

1. Press call button to turn on the light or

any other consumer connected to the

switching actuator.

Changing the start-up button

Only applies to call button module with

start-up buttons: The start-up buttons must

be swapped for call buttons that can be

labelled individually, or for suitable call

button covers.

1. Open the housing and remove the

mounting frame.

2. Unlock the module and remove it from

the mounting frame.

3. Loosen the screws with a screwdriver

(blade width 2.5 x0.4 mm) and pull off to

the front.

4. Place new call button from the front and

tighten (torque: 0.3 Nm).

5. Re-mount the module in the reverse

order.

Delete functions

Delete acoustic call button actuation

The acoustic call button actuation can be

reset completely for each call-button

module. This makes sense e.g. if a call

button has been incorrectly assigned. The

function of the call buttons is also changed

to switching action.

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

Call buttons for individual labelling

Call buttons for individual labelling can be

ordered through the Gira labelling service

(www.beschriftung.gira.de).

2. : Press and hold a Call-button module

call button for 15 s. Release the call

button after the fifth brief

acknowledgement tone (= 15 s). Then a

long acknowledgement tone sounds to

indicated that the acoustic call button

actuation is deleted for all call buttons.

3. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

4. Incorrect or no longer needed call button

assignments can be deleted using the

home stations.

To reactivate the acoustic call button

actuation, the call buttons of the module

need to be reassigned.

Deleting all assignments

1. : Start programming Control device

mode; press the “Systemprog.” button

for about 3 s until the LED flashes

(orange).

2. : Press and hold any Call-button module

call button for 18 s. After five short and

one long acknowledgement tone (=

18 s), the assignments of all call buttons

and all call button modules are deleted.

3. : Exit the programming Control device

mode; press the “Systemprog.” button

briefly until the LED goes out.

Replacing the inscription space

Call buttons with inscription space: The

label under the transparent pane can be

exchanged with the included tool without a

need to remove the call button.

Technical data

Labels

Suitably designed labels are available from

the Gira labelling service

(www.beschriftung.gira.de).

Power

supply: Via system (flat

ribbon cable, 10-pin)

Power consumption

Backlight on:

160 mW

Stand-by mode: 14 mW

Connections: 2x System

Ambient

temperature: -25 °C to +70 °C

Protection IP54

Dimensions (W x H): 106.5 x 106.5 mm

MAIER

BRAUN

MAIER

BRAUN

MAIER

10864527 40/16

System 106

call-button module

5531 9.. (1-gang)

5532 9.. (2-gang)

5533 9.. (3-gang)

5534 9.. (4-gang)

5539 000 (4-gang with

start-up buttons)

Operating instructions

Warranty

The warranty is provided in accordance with

statutory requirements via the retailer.

Please submit or send faulty devices

postage paid and with an error description

to your sales representative (retailer/

installation company).

The salesperson will forward the devices to

the Gira Service Center.

Gira

Giersiepen GmbH & Co KG

Electrical installation systems

P.O. Box 1220

42461 Radevormwald

Phone: +49 (0) 2195 602 - 0

Fax: +49 (0) 2195 602 - 191

info@gira.de

www.gira.de

Produkt Specifikationer

Mærke:	Gira
Kategori:	Intercomsystem
Model:	5533920
Bredde:	106.5 mm
Højde:	106.5 mm
Produktfarve:	Rustfrit stål
Produkttype:	Modul til opkaldsknap
Driftstemperatur (T-T):	-20 - 70 °C
Materiale:	Rustfrit stål
Monteringstype:	Overflade
Strømforbrug:	160 mA
Mærke kompatibilitet:	GIRA