Golden Lighting Torbellino 8106-M1L CDB Manual

Golden Lighting Lys Torbellino 8106-M1L CDB

Læs gratis den danske manual til Golden Lighting Torbellino 8106-M1L CDB (3 sider) i kategorien Lys. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Golden Lighting Torbellino 8106-M1L CDB, eller vil du spørge andre brugere om produktet?

Side 1/3
Canopy 1ea Hex nut 1ea Wire connectors 2ea
Mounting
bracket 1ea Nipple 1ea Top loop 1ea
Chain 1ft Canopy loop 1ea Socket rings 1ea
Chain
connector 2ea Canopy loop
collar 1ea Socket washer 1ea
Chain 1ft Mounting
screws 2ea Washer 3ea
12" Rod 3ea
Part Needed Quantity
Part Needed Quantity
Reason why ( missing, scratched, broken glass, bent, bad nish)
Comments
8106-M1L CDB
Read and review installation instruction sheet, but
do not install before assembling the xture.
F A IIXTURE SSEMBLY NSTRUCTIONS
For Customer Service, contact the place of purchase to arrange for replacement parts.
NOTE: INSTALL THE GLASS ASSEMBLY
AFTER THE FIXTURE IS HUNG.
1. By measuring determine correct number of rods
needed for proper hanging height. There are 2 optional
12" rods included.
2. To shorten the xture trim the wires to the desired
length plus at least 8~10 inches. You must use at least
one Rod (K).
3. To lengthen the xture add additional rods (ROD-12
CDB) or additional chain (CHAIN-CDB) available
separately.
Fig 1
Notice: Please review the parts listing and check for all parts before assembling the xture. If any parts are
missing or damaged, please note onthis sheet and contact the place of purchase to arrange for
replacement parts.
PARTS LIST Company Name:_______________________Co. Account #:_____________
to be lled out by retailer
PARTS & ASSEMBLY SHEET
This xture assembled PO:__________ Date: ________
Fixture Name: Torbellino 8106-M1L CDB
These two Rods may
be removed
or
additional Rods and/or
Chain may be added.
For Customer Service, contact the place of purchase to arrange for replacement parts.
PARTS & ASSEMBLY SHEET
Fixture Name: Torbellino 8106-M1L CDB
4. Pull the xture’s wire through the Rods.
5. Place Washer (S) between Rod (M) and Frame
(N),thread Rod (M) into Frame (N) until tight.
6. Place Washer (S) between Rods (M) and (L),thread
Rod (L) into Rod (M) until tight. repeat for any additional
rods.
7. Feed the xture wires through the Top loop (J) and
pull the wires until taut.
8. Thread Top loop (J) into Rod (K) until tight.
9. By measuring determine correct number of links
needed for proper hanging height. Use a pair of pliers to
open one link of the Chain then remove the excess
Chain and discard it.
10. Use one chain connector (T) to attach one end of the
chain to the Top loop (J) and close the chain connector.
11. Feed the xture wires through the Chain (every three
links) and pull the wires until taut.
Fig 2
12. Slip Canopy loop collar (H) over the Chain, then do
the same with the canopy (G).
13. When ready to complete the installation Use the
other chain connector and attach the other end of the
chain to the canopy loop (F) and close the chain
connector.
14. Make sure the weight of the chandelier is supported
by the chain-not the electrical wire.
* You may now install the xture.
15. Place the glass shade (P) over the threaded socket
(O) and place the Socket Washer (Q) onto the threaded
socket (O) and secure both by threading the Socket ring
(R) until tight.
16. Install the light bulb in accordance with the xture’s
specications.
(DO NOT EXCEED MAXIMUM WATTAGE RATING!)
G
CHAIN
J
H
F
expanded view of assembly
T
S


Produkt Specifikationer

Mærke: Golden Lighting
Kategori: Lys
Model: Torbellino 8106-M1L CDB

Har du brug for hjælp?

Hvis du har brug for hjælp til Golden Lighting Torbellino 8106-M1L CDB stil et spørgsmål nedenfor, og andre brugere vil svare dig