Harley Davidson J01521 (1999) Manual

Harley Davidson Motor J01521 (1999)

Læs gratis den danske manual til Harley Davidson J01521 (1999) (12 sider) i kategorien Motor. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om Harley Davidson J01521 (1999), eller vil du spørge andre brugere om produktet?

Side 1/12
INSTRUCTIONS
-J01521 REV. 3-22-99
MOTORCYCLE SERVICE LIFT ADAPTER KIT FOR DYNA TC88 MODELS
General
This kit is designed for 1999 and later Dyna TC88 model
motorcycles to be used with Motorcycle Service Lift (P/N
94653-98) and Motorcycle Cleaning Stand (P/N 94652-98).
Before using your adapter kit, it is your responsibility to read
and follow these installation and operating instructions
Harley Davidson strongly recommends that the
following procedures be performed by 2 people. Failure
to follow instructions can result in death or serious
injury.
This kit consists of the following components:
Qty DESCRIPTION PART No.
3 Frame lift adapter not sold
1 Frame leveling
extrusion not sold
Installation
A Service Manual for your motorcycle is available at your
Harley-Davidson Dealer.
1. See Figure 1. Position the motorcycle on a straight and
level surface. While the bike rests on the Jiffy Stand,
straighten the front wheel and place the frame leveling
extrusion under the front tire to keep the tire straight.
2. Slide the motorcycle lift (fully lowered) under the bike
from the right side (opposite jiffy stand side) lining up
the frame rails with each of the perpendicular jacking
rails on the lift. When properly aligned, the left frame rail
will be approximately 1” from the lift end section (Figure
2) and lift base will be adjacent to the Jiffy Stand (Figure
3). This will allow bike to be centered when moved to an
upright position.
1WARNING
®
1 of 3
Kit Number 98965-99
i01478
Figure 1 Frame Level Extrusion
Figure 2.
Figure 3.
i01479
i01480
Frame leveling extrusion
Side of frame
approximately
1” from end of
lift rail
Bottom of
frame rail
Lift adjacent to
Jiffy Stand
Jiffy
Stand
extended
Forward
lift rail
Forward
lift rail
3. See Figure 4. Install one frame lift adapter to the right
front frame rail. When properly installed, frame lift
adapter should butt against frame/footpeg support as
shown.
4. Holding motorcycle securely, carefully lean the bike
slightly to the right and install one of the frame lift
adapters to the left front frame rail (Figure 5) and one
frame lift adapter to the left rear frame rail (Figure 6).
Note that rear frame lift adapter follows the frame rail at
an angle inward under the bike.
5. Recheck overall position of lift. Frame lift adapters
should be centered over lift rails. Release friction pad
latch as shown in Figure 7.
-J01521 2 of 3
Figure 4.
Figure 5.
i01481
Figure 7.
Frame rail adapter
should rest snugly
against
footpeg/frame
support
i01484
Figure 6.
Use brake to
help hold bike
securely
Install frame lift
adapter over front
section of rail
i01483
Install frame lift adapter over
rear section of frame rail
Friction pad
latch Friction pad
i01482
Frame lift adapter


Produkt Specifikationer

Mærke: Harley Davidson
Kategori: Motor
Model: J01521 (1999)

Har du brug for hjælp?

Hvis du har brug for hjælp til Harley Davidson J01521 (1999) stil et spørgsmål nedenfor, og andre brugere vil svare dig