Honeywell CT410A1001/E1 Manual

Honeywell Termostat CT410A1001/E1

Læs gratis den danske manual til Honeywell CT410A1001/E1 (4 sider) i kategorien Termostat. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Honeywell CT410A1001/E1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTALLATION INSTRUCTIONS

69-1562-02

T410A,B Line Voltage

Electric Heat Thermostats

T410A provides single-line break.

T410B provides double-line break.

Temperature Range: 40°F to 80°F (4°C to 27°C)

Electrical Ratings: 60 Hz noninductive

22A at 120-240 Vac; 19A at 277 Vac

Your Resideo Thermostat

Your new Resideo T410 Electric Heating Thermostat

provides line voltage control of a radiant cable,

electric baseboard, and resistive-rated fan forced

heaters within the ratings listed above.

WARNING

Electric shock hazard

This thermostat is a line voltage control (120

Volts to 277 Volts.) Do not install it if you are

not completely familiar with house wiring. If

handled improperly, there can be risk of a 120

Volt to 277 Volt electric shock hazard, which

may cause serious injury or death.

MERCURY NOTICE

If this control is replacing a control that

contains mercury in a sealed tube, do not

place you old control in the trash. Dispose of

properly.

Contact you local waste management

authority for instruction regarding recycling

and the proper disposal of a old control.

1 PREPARATION

Proper installation of your Resideo thermostat will

occur if you follow these instructions STEP-

BYSTEP. It is recommended that as you read,

understand and complete each step, you check it

off with pencil or pen.

Check thermostat suitability for your home system

by reviewing the ratings listed on this page.

Make certain that your heating system is working,

especially if it has been inoperative for a length of

time. If the system does not work, contact your

local electrician for assistance.

Carefully unpack your new thermostat. To avoid

damage to the sensing element, do NOT remove

the thermostat cover until wiring has been

completed.

Save packages of screws, instructions, receipt and

proof-of-purchase.

T410A,B LINE VOLTAGE ELECTRIC HEAT THERMOSTATS

69-1562—02 2

2 REMOVE OLD

THERMOSTAT

WARNING

Electric shock hazard

Begin by turning off power to the heating

circuit at the main service panel.

Remove cover of old thermostat. Cover normally

snaps off when pulled firmly from the bottom. If it

resists, check for a screw that locks the cover.

Loosen screws holding thermostat base to outlet

box and lift away.

Disconnect wires from old thermostat. As you

disconnect each wire, tape the end and label it with

the letter of the terminal designation to make

reconnection to new thermostat easier.

Check the old insulation for cracks, nicks or fraying,

and apply high quality plastic tape where necessary

for adequate insulation.

Retain the old thermostat for reference purposes

and until your new thermostat is functioning

smoothly.

3 WIRE AND MOUNT NEW

THERMOSTAT

Connect wires to the thermostat as shown in the

applicable wiring diagram.

Remove thermostat cover by grasping the top and

bottom ends with fingers, and pulling outward.

Push the wires into the outlet box, and insert the

thermostat into the box for mounting by pushing

against top and bottom of the thermostat base.

IMPORTANT

Do not press on setting knob.

Secure the thermostat to the box with the two

captive mounting screws provided.

Replace thermostat cover.

Set knob to desired room temperature.

IMPORTANT

Rough handling or strong pressure can dam-

age knob or sensing element, and change cali-

bration.

Fig. 1.

4 CHECK OUT THERMOSTAT

Turn on the power to the heating system.

Turn setting knob all the way clockwise ; listen

for clicking sound as switch makes contact. Electric

heater should begin operation.

Turn knob all the way counterclockwise ; listen

for clicking sound as switch breaks contact. Electric

heater should shut off.

5 SETTING THERMOSTAT

Begin with knob to the desired setting (typically

70°F [20°C] on the scale).

If this setting is not satisfactory after at least two

hours of operation, turn setting knob upscale to

raise the temperature, or downscale to lower the

temperature. Move knob only a degree each time.

(HOT) L2

244

POWER SUPPLY. PROVIDE DISCONNECT MEANS AND OVERLOAD

PROTECTION AS REQUIRED.

BREAKS ON POSITIVE OFF.

EXPOSED UNUSED LEADWIRES TO BE PROPERLY INSULATED.

THERMALLY ACTIVATED—BREAKS ON TEMPERATURE

RISE. MAKES ON TEMPERATURE FALL.

L2 L1 L1

T2 T1 T1

T410AT410B

ELECTRIC

HEATER

CAUTION:

SPECIAL SERVICE CO/ALR SOLDERLESS CONNECTORS MUST

BE USED WHEN CONNECTING WITH ALUMINUM CONDUCTORS;

OTHERWISE, A FIRE HAZARD CAN RESULT.

ELECTRIC

HEATER

M19099

Produkt Specifikationer

Mærke:	Honeywell
Kategori:	Termostat
Model:	CT410A1001/E1

Har du brug for hjælp?

Hvis du har brug for hjælp til Honeywell CT410A1001/E1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Termostat Honeywell Manualer

Honeywell CT50K1028/E Manual

12 August 2025

Honeywell RET97B5D1002/U Manual

12 August 2025

Honeywell RCHT9510WFW2001/W Manual

12 August 2025

Honeywell CT87K1004/E1 Manual

12 August 2025

Honeywell YCT87N1006 Manual

12 August 2025

Honeywell RTH7500D1049/A Manual

12 August 2025

Honeywell YCT50K1006 Manual

12 August 2025

Honeywell RTH2510B1000/U Manual

12 August 2025

Honeywell RTH221B1039/E1 Manual

12 August 2025

Honeywell RLV3150A1004/E Manual

12 August 2025

Termostat Manualer

Nyeste Termostat Manualer

GE RAK190V Manual

12 August 2025

Daikin BRC1H519W Manual

11 August 2025

Daikin BRC1D528 Manual

11 August 2025

Carrier Infinity SYSTXCCITC01-B Manual

10 August 2025

Hager WXF315 Manual

9 August 2025

Hama 176592 Manual

9 August 2025

Eberle UTE 1002 Manual

7 August 2025

Eberle UTE 1012 Manual

7 August 2025

Eberle SSR-E 6905 Manual

7 August 2025

JUNG CD 500 Manual

7 August 2025