Horizon Fitness Express 200 Manual

Horizon Fitness Cykel træner Express 200

Læs gratis den danske manual til Horizon Fitness Express 200 (1 sider) i kategorien Cykel træner. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Horizon Fitness Express 200, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

REAR FOOT TUBE

REAR FOOT PAD

POP PIN

SEAT

GRIP PULSE

CONSOLE

CONSOLE DATA CABLE

TENSION KNO

CABLE

CTION

EBARS

U N P A C K I N G

Unpack your Exercise Bike where you will be

using it. Place your bike on a level flat surface. It

is recommended that you place a protective cov-

ering on your floor. You will only need to attach

the following items. Verify that the following parts

and tools are included:

Parts

•1 Rear Foot Tube

•2 Handlebar Set

•1 Seat Post

•1 Seat

•1 Console Mast

•1 Console Mast Boot

•2 Mobile Wheels

•1 Console

•2 AA Batteries

•2 Pedals

•2 Wheel Sleeves

•1 Tension Knob

•2 Handlebar Links

•1 Hardware Pack (contents listed below)

E) 13mm Nut

Quantity: 2

J) 14mm Washer

Quantity: 2

K) 20mm Bolt

Quantity: 2

I) 12mm Screw

Quantity: 2

A) 20mm Bolt

Quantity: 2

D) 15mm Bolt

Quantity: 4

F) 45mm Bolt

Quantity: 2

Tools (included)

•5mm Allen Wrench/

Phillips Screw Driver

•Flat Wrench

NOTE: It is recommended that you apply grease

to the threads of each bolt as you assemble your

Exercise Bike, to prevent loosening and noise.

Also, during each assembly step, ensure that ALL

nuts and bolts are in place and partially threaded

in before completely tightening any ONE bolt.

STEP 4

Connecting the Tension Knob

a. Remove the 20mm long bolt (Q)

on the back of the tension knob.

b. Turn the tension knob to level 15.

Connect the tension knob to the

bottom of the tension knob cable

(Figure A, Step 2).

c. Grasp the tension knob and firmly

pull the tension knob assembly

away from the machine in order to

attach to the top of the tension knob

cable (Figure B, Step 3). Make sure

that the copper cable end is seated

properly into the "key hole".

d. Insert the tension knob into the rec-

tangular opening on the console

mast (Figure C, Step 5).

e. Secure the tension knob with the

20mm bolt (C) by using a screw

driver (Figure D, Step 6).

STEP 1

Attach the Front Foot Wheels

a. Insert the wheel sleeves on each

side of the front wheel tube.

b. Align the holes in the wheel sleeves

with the holes in the wheel tube.

Insert two 12mm screws (I) and

secure with the screwdriver.

c. Attach the mobile wheels to the

wheel sleeves. Insert two 14mm

washers (T) and two 20mm bolts

(K) and secure with a screwdriver.

STEP 8

Attach the Pedals

a. Attach pedal spacer (P), handlebar

link, and 30mm washer (O) onto the

right pedal. Note: The pedals are

labeled on the end of each thread-

ed shaft for reference.

b. Tighten the pedal with the flat

wrench.

c. Repeat for left side.

STEP 5

Attaching the Dual-Action

Handlebars

a. Attach console mast spacer (C)

onto the console mast.

b. Align the holes of the handlebar

and slide it onto the console mast.

Attach a 35mm washer (B) and

20mm bolt (A) and secure with a

5mm Allen wrench. Repeat for

other side.

c. Insert two link arm spacers (H,G)

into the lower handlebar bracket.

d. Align the holes for the handlebar

link and the lower handlebar.

Insert a 45mm bolt (F) and

secure with a 13mm nut (E) using

a flat wrench. Repeat for other

side.

STEP 6

Attaching the Console

a. Open the battery cover on the

back of the console, insert two AA

batteries into the console and

replace the battery cover.

b. Connect the cables from the con

sole to the console cables running

through the console mast, mak-

ing sure that both ends snap togeth-

er tight.

c. Attach the console to the console

mast plate with the 15mm screws

(R). Secure using a screwdriver.

Note: Screws (R) are located on the

back side of the console.

STEP 3

Attaching the Console Mast

a. Unfold the console cable and the

tension knob cable, which is folded

into the console mast base.

b. Slide the console mast boot onto

the bottom of the console mast.

c. Slide the tension knob cable and

the console cable through the con-

sole mast. (Note: The tension knob

cable will only pull as far as the rec-

tangular opening in the console

mast. The console cable will need

to be pulled through the end of the

console mast.) To assist in pulling

the console cable and tension knob

cable through the console mast,

there should be a guide wire

attached to the top of the console

mast.

d. Insert the console mast into the

base, secure both sides of the

mast with four 15mm bolts (D)

using the 5mm allen wrench. Slide

the console mast boot into place.

STEP 7

Attach the Seat

a. Remove the three nuts (S) and

washers (T) from the bottom of the

seat.

b. Attach the seat to the seat post with

the three nuts (S) and washers (T),

securing with the flat wrench.

c. Loosen the pop pin by turning it one

or two revolutions, then pull the pop

pin mechanism to the outward

position.

d. With the pop pin in the outward

position, slide the seat post into

the base.

e. Release the pop pin and tighten to

the proper position.

Figure A

Figure B

Figure C

Figure D

C U S T O M E R A S S I S T A N C E C E N T E R 1 . 8 8 8 . 9 9 3 . 3 1 9 9 o r w w w . h o r i z o n f i t n e s s . c o m

H a r d w a r e (Actual Size)

Express

B) 35mm Washer

Quantity: 2

G) Linkarm Spacer (Inner)

Quantity:2

C) Teflon Washer

Quantity: 2

N) 20mm Arc Washer

Quantity: 4

O) Pedal Spacer (Outer)

Quantity: 2

H) Linkarm Spacer (Outer)

Quantity:2

P) Pedal Spacer (Inner)

Quantity: 2

L) 90mm Bolt

Quantity: 2

M) Acorn Nut

Quantity: 2

STEP 2

Attach the Rear Foot Tube and

Pads

a. Align the holes of the rear foot

tube with the holes in the base

frame.

b. Insert two 90mm bolts (L), two

20mm arc washers (N) and acorn

nut (M) secure with a 5mm allen

wrench.

c. Slide the rear foot pads to each

end of the rear foot tube.

NEW Express 200 assembly guidev1.0.qxd 3/12/2003 4:12 PM Page 1

Produkt Specifikationer

Mærke:	Horizon Fitness
Kategori:	Cykel træner
Model:	Express 200

Har du brug for hjælp?

Hvis du har brug for hjælp til Horizon Fitness Express 200 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Cykel træner Horizon Fitness Manualer

Horizon Fitness R52HR Manual

5 September 2024

Horizon Fitness Limited R6055HR Manual

5 September 2024

Horizon Fitness RB1 Manual

5 September 2024

Horizon Fitness Elite 3.1B Manual

5 September 2024

Horizon Fitness RC40 Manual

5 September 2024

Horizon Fitness B701 Manual

5 September 2024

Horizon Fitness R51 Manual

5 September 2024

Horizon Fitness Express 200 Manual

5 September 2024

Horizon Fitness Express II Manual

5 September 2024

Horizon Fitness R30 Manual

5 September 2024

Cykel træner Manualer

Nyeste Cykel træner Manualer

Gymform Swivel Manual

4 Marts 2025

LifeSpan Ampera Office Bike Manual

30 Januar 2025

LifeSpan C7000i Manual

6 Januar 2025

Wahoo Smart Bike Trainer Manual

30 December 2025

Wahoo Kickr Smart Bike Trainer Manual

30 December 2025

Cecotec Drumfit CrossFit 3000 Eolo Manual

26 December 2024

Cecotec DrumFit Static 6000 Seat Manual

26 December 2024

Fortis FSMNPFDLBKA Manual

19 December 2024

Fortis FSMNMFPDBKA Manual

19 December 2024

Cardiostrong EX90 Touch Manual

15 December 2024