HP Aruba Unified AP-535 Manual

HP Adgangspunkt Aruba Unified AP-535

Læs gratis den danske manual til HP Aruba Unified AP-535 (14 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 79 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 40 anmeldelser. Har du et spørgsmål om HP Aruba Unified AP-535, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/14
Aruba 530 Series Campus Access Points
Installation Guide
Installation Guide | May 2019 1
Aruba 530 Series access points (AP-534 and AP-535) are high-performance, multi-radio wireless devices that can
be deployed in either controller-based (ArubaOS) or controllerless (InstantOS) network environments. These
access points deliver high-performance concurrent 2.4 GHz and 5 GHz 802.11ax Wi-Fi functionality with 4x4
MIMO radios, while also supporting legacy 802.11a/b/g/n/ac wireless services.
Ethernet ports located on the back of this access point are used to connect the device to the wired networking
infrastructure and to provide power over Ethernet (PoE) to the device (802.3at class 4 or 802.3bt class 5).
In addition to both Wi-Fi radios, these APs also incorporate a Bluetooth Low Energy (BLE) and Zigbee radio,
supporting a variety of use-cases and services, such as locationing and IoT.
A variety of mounting scenarios is supported by a range of mount kits (sold separately). Make sure to purchase
the correct mount kit for the intended deployment of the AP.
Hardware Overview
The following sections outline the hardware components of the 530 Series access point.
Figure 1 Aruba AP-535 (front view)
Figure 2 Aruba AP-534 (LEDs)
2Aruba 530 Series Campus Access Points | Installation Guide
External Antenna Connectors
The AP-534 access points are equipped with four external antenna connectors located on the front corners of
the access point (see Figure 2). Antenna ports A0 through A3 (corresponding with radio chains 0 through 3), are
used for both radios and bands (RF signals are diplexed).
LEDs
The LED displays located on the front panel of the access point indicate the following functions:
System Status
The System Status LED indicates the operating condition of the access point, See Table 1.
Table 1 System Status LEDs
1 Blinking: one second on/one second off, 2 second cycle.
2 Flashing Pattern 1: mostly on, briefly off, 2 second cycle.
3 Flashing Pattern 2: mostly off, briefly on, 2 second cycle.
Radio Status
The Radio Status LED indicates the operating mode of the access point’s radios. See Table 2.
!
!
!
!!
External antennas for this device must be installed by an Aruba Certified Mobility Professional (ACMP) or other
Aruba-certified technician, using manufacturer-approved antennas only.
The Equivalent Isotropically Radiated Power (EIRP) levels for all external antenna devices must not exceed the
regulatory limit set by the host country/domain.
Installers are required to record the antenna gain for this device in the system management software. A list of
approved antennas can be found at: http://www.arubanetworks.com/assets/og/OG_AP-530Series.pdf.
Les antennes externes pour cet appareil doivent être installées par un professionnel de la mobilité certifié Aruba
(ACMP) ou un autre technicien certifié Aruba, en utilisant uniquement des antennes approuvées par le fabricant.
Les niveaux équivalents de puissance à rayonnement isotrope (EIRP) pour tous les périphériques d'antenne
externe ne doivent pas dépasser la limite réglementaire définie par le pays hôte / domaine.
Les installateurs doivent enregistrer le gain d'antenne pour cet appareil dans le logiciel de gestion du système.
Une liste d'antennes approuvées peut être trouvée à http://www.arubanetworks.com/assets/og/OG_AP-
530Series.pdf.
Color/State Meaning
Off Device powered off
Green- blinking 1Device booting, not ready
Green- solid Device ready, fully functional, no network restrictions
Green- flashing pattern 12Device ready, fully functional, either uplink negotiated in sub-optimal speed
(<1Gbps)
Green- flashing pattern 23Deep sleep mode
Amber- solid Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), no network restrictions
Amber- flashing pattern 1 Device ready, restricted power mode (limited PoE power available, or IPM
restrictions applied), uplink negotiated in sub-optimal speed (<1Gbps)
Red System error condition - Immediate attention required

Produkt Specifikationer

Mærke: HP
Kategori: Adgangspunkt
Model: Aruba Unified AP-535

Har du brug for hjælp?

Hvis du har brug for hjælp til HP Aruba Unified AP-535 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Adgangspunkt HP Manualer

HP

HP Aruba Instant On AP11 Manual

4 Juli 2025
HP

HP Aruba AP-565 Manual

10 August 2024
HP

HP Aruba Unified AP-505 Manual

28 Juni 2024
HP

HP Aruba Unified AP-345 Manual

28 Juni 2024
HP

HP Aruba Instant On AP22 Manual

27 April 2024
HP

HP Aruba Unified AP-535 Manual

8 Marts 2024
HP

HP Aruba RAP-108 Manual

9 Maj 2023
HP

HP 417 Manual

4 December 2022

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

TP-Link

TP-Link Omada EAP215-Bridge KIT Manual

12 August 2025
Tenda

Tenda OAP1200 Manual

12 August 2025
Aruba

Aruba R9B33A Manual

10 August 2025
Planet

Planet IAP-1800AX Manual

8 August 2025
Planet

Planet WDAP-850AC Manual

8 August 2025
Planet

Planet WDAP-W1200E Manual

8 August 2025
Planet

Planet WDAP-C3000AX Manual

8 August 2025
Planet

Planet WDAP-C1800AX Manual

8 August 2025
Planet

Planet IAP-2400AX Manual

8 August 2025
Planet

Planet WDAP-C7210E Manual

8 August 2025