HP Aruba RAP-108 Manual

HP Adgangspunkt Aruba RAP-108

Læs gratis den danske manual til HP Aruba RAP-108 (2 sider) i kategorien Adgangspunkt. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om HP Aruba RAP-108, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
Aruba RAP-108 and RAP-109 Remote Access Point
Installation Guide
The Aruba RAP-108 and RAP-109 are dual-radio, dual-band remote access points
that supports the IEEE 802.11n standard for high-performance WLAN. These
access point uses MIMO (Multiple-in, Multiple-out) technology and other high-
throughput mode techniques to deliver high-performance, 802.11n 2.4 GHz and 5
GHz functionality while simultaneously supporting existing 802.11a/b/g wireless
services.
The RAP-108/RAP-109 ships with Aruba Instant software. Therefore, out of the
box, the RAP-108/RAP-109 will operate as a Virtual Controller (VC) or an Instant
AP. However, the RAP-108/RAP-109 can be converted to operate as a Remote AP
(RAP). For information about the IAP to RAP conversion, see .RAP Conversion
The Aruba RAP-108/RAP-109 remote access point provides the following
capabilities:
Wireless transceiver
Protocol-independent networking functionality
IEEE 802.11a/b/g/n operation as a wireless access point
IEEE 802.11a/b/g/n operation as a wireless air monitor
Compatibility with IEEE 802.3af and 802.3at
Package Contents
RAP-108 or RAP-109 Remote Access Point
RAP-108/RAP-109 Mounting Stand
Installation Guide
RAP-108/RAP-109 Hardware Overview
Figure 1 Ports
Reset Button
The reset button can be used to return the AP to factory default settings. To reset
the AP:
1. Power off the AP.
2. Press and hold the reset button using a small, narrow object, such as a
paperclip.
3. Power-on the AP without releasing the reset button. The power LED will
flash within 5 seconds.
4. Release the reset button.
The power LED will flash again within 15 seconds indicating that the reset is
completed. The AP will now continue to boot with the factory default settings.
USB Interface
The RAP-108/RAP-109 is equipped with a USB interface for connectivity with
cellular modems.
Console Port
Use the console port to connect to a terminal for direct local management.
ENET 0
For primary network connectivity, RAP-108/RAP-109 is equipped with a 10/100/
1000BASE-T (RJ-45) auto-sensing, MDI/MDX Gigabit Ethernet port. This port
supports IEEE 802.3af Power over Ethernet (PoE) compliance, accepting 48VDC
as a standard defined Powered Device (PD) from a Power Sourcing Equipment
(PSE) such as a PoE midspan injector, or network infrastructure that supports
PoE.
ENET 1
For secondary network connectivity, RAP-108/RAP-109 is equipped with a 10/
100BASE-T (RJ-45) auto-sensing, MDI/MDX Fast Ethernet port.
DC Power Socket
If PoE is not available, an optional Aruba AP AC-DC adapter kit (sold separately)
can be used to power the RAP-108/RAP-109.
External Antenna Connectors (RAP-108 Only)
The RAP-108 is equipped with two RP-SMA external antenna connectors and
requires the use of two dual-band antennas. These ports are marked ANT0 and
ANT1, matching radio chains 0 and 1.
In order to ensure accurate RF power level setting and reporting in software, as
well as compliance with any regulatory restrictions, the correct gain for
antennas used (adjusted for any additional cabling loss, if applicable) needs to
be entered in software when provisioning the RAP-108. Two antenna gain
numbers are needed for this; one for each supported band (2.4GHz and 5GHz).
These numbers can be obtained from the antenna datasheet or specifications.
Antenna gain for RAP-109 is hardcoded to the correct values already, so there is
no need for any additional action on that platform.
Figure 2 LEDs
LEDs
PWR: Indicates whether or not the RAP-108/RAP-109 is powered-on
ENET0 and ENET1: Indicates the status of the RAP-108/RAP-109’s Ethernet
ports
5 GHz: Indicates the status of the 802.11a/n radio
2.4 GHz: Indicates the status of the 802.11b/g/n radio
Installing the AP
Tabletop Mounting
The RAP-108/RAP-109 is shipped with a stand to use on flat (i.e. table top)
surfaces. Place the RAP-108/RAP-109 in the stand (see ) and place the Figure 3
stand on a flat, level surface.
To attach the RAP to the stand:
1. Align the center peg of the stand with recessed hole on the unit.
2. Align the mounting posts on the back of the AP with corresponding openings
on the stand.
3. Rotate the AP clockwise until it clicks into place.
Figure 3 Stand Installation
Connecting the Required Cables
The RAP-108/RAP-109 must be connected to a network device that has access to
the Internet, such as a router or modem. To complete the installation of the RAP-
108/RAP-109:
1. Connect one end of the provided RJ-45 cable to port E0 on the RAP-108/RAP-
109.
2. Connect the other end of the RJ-45 cable to a free RJ-45 port on your modem
or router.
3. Attach the provided power adapter to the DC IN port on the RAP-108/RAP-
109.
4. Connect the other end of the power adapter to a power outlet.
The RAP-108/RAP-109 is now powered on. To verify this, ensure that the PWR
LED is solid green.
Verifying Successful Installation
Once the RAP-108/RAP-109’s PWR LED has come up, the device will take 2 to 3
minutes to complete the boot cycle. Once the boot cycle is complete, you can
connect to your company or corporate network.
RAP Conversion
If your network administrator has instructed you to convert the RAP-108/RAP-
109 to work in RAP mode, follow the process below to complete the RAP
conversion.
1. Power up the RAP-108/RAP-109.
2. Connect to SSID.Instant
3. Login to the RAP-108/RAP-109 by navigating to http://
instant.arubanetworks.com and login to the Instant WebUI. The default
username is and the default password is . See the included admin admin
Aruba Instant Quick Start Guide for more information.
4. Navigate to the tab in the top right.Maintenance
5. Click on the tab.Convert
6. Select from the drop Remote APs managed by a Mobility Controller
down menu.
7. Enter the IP address of the controller. This is provided by your network
administrator.
8. Click to complete the conversion (see ).Convert Now Figure 4
9. The RAP-108/RAP-109 will reboot and begin operating in RAP mode.
Figure 4 IAP-RAP Conversion over the Internet
The RAP-108/RAP-109 requires Aruba Instant 3.2 or ArubaOS 6.2.
Inform your supplier if there are any incorrect, missing, or damaged
parts. If possible, retain the carton, including the original packing
materials. Use these materials to repack and return the unit to the
supplier if needed.
The USB interface is disabled when the RAP-108/RAP-109 is powered from
802.3af PoE.
ENET 1
ENET 0
56V 350mA
1.25A
CONSOLE
Table 1 RAP-108/RAP-109 Series LED Meanings
LED Color/State Meaning
PWR Off No power to AP
Red steady System initializing
Green flashing Device booting, not ready
Green steady Device ready
ENET0 Off No link
Amber 10/100 Mbps link
Green 1000 Mbps link
Flashing Ethernet link activity
ENET1 Off No link
Green 10/100 Mbps link
Flashing Ethernet link activity
5 GHz Off 5 GHz radio is disabled
Amber steady 5 GHz radio enabled in WLAN
mode
Green steady 5 GHz radio enabled in 11n mode
Green flashing 5 GHz Air Monitor mode
2.4 G Hz
5 GHz
ENET 1
ENET 0
PWR
2.4 GHz Off 2.4 GHz radio disabled
Amber steady 2.4 GHz radio enabled in WLAN
mode
Green steady 2.4 GHz radio enabled in 11n
mode
Green flashing 2.4 GHz Air Monitor mode
Table 1 RAP-108/RAP-109 Series LED Meanings (Continued)
LED Color/State Meaning
RAP-108_02

Produkt Specifikationer

Mærke: HP
Kategori: Adgangspunkt
Model: Aruba RAP-108

Har du brug for hjælp?

Hvis du har brug for hjælp til HP Aruba RAP-108 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Adgangspunkt HP Manualer

HP

HP Aruba Instant On AP11 Manual

4 Juli 2025
HP

HP Aruba AP-565 Manual

10 August 2024
HP

HP Aruba Unified AP-505 Manual

28 Juni 2024
HP

HP Aruba Unified AP-345 Manual

28 Juni 2024
HP

HP Aruba Instant On AP22 Manual

27 April 2024
HP

HP Aruba Unified AP-535 Manual

8 Marts 2024
HP

HP Aruba RAP-108 Manual

9 Maj 2023
HP

HP 417 Manual

4 December 2022

Adgangspunkt Manualer

Nyeste Adgangspunkt Manualer

Draytek

Draytek VigorAP 700 Manual

19 Oktober 2025
Lancom

Lancom LN-860 Manual

16 Oktober 2025
Mikrotik

Mikrotik SXT 5 ac Manual

15 Oktober 2025
Lancom

Lancom LX-7400 Manual

8 Oktober 2025
Draytek

Draytek Vigor AP 1000C Manual

7 Oktober 2025
Conceptronic

Conceptronic C150APM Manual

7 Oktober 2025
Draytek

Draytek VigorAP 910C Manual

6 Oktober 2025
Draytek

Draytek VigorAP 1062C Manual

6 Oktober 2025
Draytek

Draytek AP918RPD Manual

6 Oktober 2025
Draytek

Draytek VigorAP 918R Manual

6 Oktober 2025