Icom HS-102 Manual

Icom Headset HS-102

Læs gratis den danske manual til Icom HS-102 (2 sider) i kategorien Headset. Denne vejledning er vurderet som hjælpsom af 2 personer og har en gennemsnitlig bedømmelse på 4.1 stjerner ud af 1.5 anmeldelser. Har du et spørgsmål om Icom HS-102, eller vil du spørge andre brugere om produktet?

Side 1/2
Gracias por haber adquirido este prodcuto Icom.
Los auriculares HS-102 son para conectar con el
OPC-2359 cable de interruptor PTT.
Lea las instrucciones completamente antes de
utilizar el HS-102.
INSTRUCCIONES
AURICULARES
HS-102
de Icom Incorporated (Japón) en los Estados Unidos,
Reino Unido, Alemania, Francia, España, Rusia,
Australia, Nueva Zelandia y/u otros países.
Los auriculares no tienen la protección resistente
al agua y polvo.
NUNCA coloque objetos pesados sobre los
auriculares o no los pellizque.
NO deje caer los auriculares sobre una superficie
dura. Esto podría dañar los auriculares.
NO exponga los auriculares a la luz directa del sol.
Esto puede deformar o decolorar los auriculares.
UTILICE únicamente con el cable especificado
por Icom. De lo contrario esto podría dañar los
auriculares o no podrían funcionar correctamente.
MANTENGA los auriculares fuera del alcance de
los niños.
Se requiere el OPC-2359 (se compran por separado).
1) Inserte los soportes laterales en la unidad
principal del micrófono.
2) Conecte los auriculares y gire los soportes
laterales.
PRECAUCIONES ASAMBLEA DE AURICULARES
Lado derecho
Lado izquierdo
CUIDADO: Tenga cuidado de no hacer daño a sus
dedos o uñas al insertar o quitar los soportes.
Quitar los soportes laterales:
Quite los soportes como se
muestra a la derecha.
Soportes laterales
Auriculares
Ajuste los
soportes a
su cabeza.
Micrófono
2.5 mm (d)
Conector de
auriculares
Interruptor de
sensibilidad del
micrófono
(Por defecto: HI)
OPC-2359
El símbolo de reciclaje tachado en el
producto, documentación o embalaje
le recuerda que en la Unión Europea,
todos los productos eléctricos y
electrónicos, baterías y acumuladores
(baterías recargables) deben llevarse a puntos
de recogida concretos al final de su vida útil.
No deseche estos productos con la basura
doméstica no clasificada.
Deséchelos de acuerdo con las normativas y
leyes locales aplicables.
DESECHO
Imagen
Acerca de la sensibilidad del micrófono
Seleccione la sensibilidad alta (HI) o baja (LO).
Si siente alguna molestia con
las piezas de los auriculares
estándar, cámbielas con las
piezas estrechas.
Asegúrese de que las piezas
estén colocadas firmamente.
PIEZAS AURICULARES
(0.35”) (0.41”)
9 mm 10.5 mm
Unidad principal
del micrófono
Soportes laterales
Merci d’avoir choisi ce produit ICOM.
Le casque HS-102 doit être connecté avec le
câble PTT référence OPC-2359. Merci de lire
attentivement les instructions ci-après avant
toute utilisation du casque HS-102.
INSTRUCTIONS
CASQUE
HS-102
de commerce enregistrées d'Icom Incorporated
(Japon) pour le Japon, les États-Unis, le Royaume-
Uni, l'Allemagne, la France, l'Espagne, la Russie et/ou
d'autres pays.
Ce casque n’est pas étanche à l’eau et à la
poussière.
NE JAMAIS poser d’objet lourd sur le casque.
NE PAS faire tomber le casque sur une surface
dure pour éviter de l’endommager
.
NE PAS exposer le casque directement au rayon
du soleil afin qu’il ne se déforme pas ou que sa
couleur se ternisse.
UTILISER toujours ce casque avec les câbles
ICOM adaptés afin de ne pas l’endommager et
de permettre un fonctionnement optimal.
GARDER le casque hors de portée des enfants.
Le câble optionnel OPC-2359 est nécessaire pour
le montage.
1) Insérez le support latéral au niveau du boitier
du microphone.
2) Branchez l’oreillette et faites pivoter les
supports latéraux.
AVERTISSEMENT MONTAGE DU CASQUE
Supports latéraux
Utilisation
pour droitier
Utilisation
pour gaucher
Boitier du microphone
AVERTISSEMENT: attention de ne pas vous blesser
le doigt quand vous manipulez le support latéral.
Enlever le support lateral:
Enlever le support latéral
comme indiqué dans le
schéma de droite.
Supports latéraux
Oreillette
Ajuster le
support latéral
à votre tête.
Microphone
Jack
oreillette
2.5 mm
Bouton de réglage
de la sensibilité
du microphone
(réglage par défaut
avec sensibilité
élevée)
OPC-2359
Le pictogramme poubelle barrée sur
notre produit, notre documentation ou
nos emballages vous rappelle qu’au sein
de l’Union européenne, tous les produits
électriques et électroniques, batteries et
accumulateurs (batteries rechargeables) doivent
être mise au rebut dans les centres de collecte
indiqués à la fin de leur période de vie. Vous ne
devez pas mettre au rebut ces produits avec les
déchets municipaux non triés.
Ils doivent être mis au rebut dans le respect de
la réglementation en vigueur dans votre secteur.
MISE AU REBUT
Image
A propos de la sensibilité du microphone
En fonction des besoins, régler la sensibilité sur la
position HI ou LO.
Si vous ressentez un inconfort avec l’oreillette
standard, vous pouvez la
remplacer par celle plus fine
également fournie.
Assurez-vous que l’oreillette
est correctement fixée.
A PROPOS DE L’OREILLETTE
(0.35”) (0.41”)
9 mm 10.5 mm
Thank you for choosing this Icom product.
The HS-102 is the headset to connect headset
with the OPC-2359 .ptt switch cable
Please read these instructions thoroughly
before using the HS-102.
INSTRUCTIONS
HEADSET
HS-102
Icom, Icom Inc. and Icom logo are registered
United States, the United Kingdom, Germany, France,
Spain, Russia, Australia, New Zealand, and/or other
countries.
The headset does not have waterproof or
dustproof protection.
NEVER place any heavy object on the
headset, or pinch it.
DO NOT drop the headset on a hard surface.
Otherwise it may damage the headset.
DO NOT expose the headset to direct sunlight.
It may deform or discolor the headset.
USE with only the specified Icom cable.
Otherwise it may damage the headset, or
the headset may not function correctly.
KEEP the headset out of the reach of children.
The OPC-2359 (purchase separately) is required.
1) Insert the side support into the microphone’s
main unit.
2) Connect the earphone and rotate the side
supports.
PRECAUTIONS HEADSET ASSEMBLY
Side supports
Right side use
Left side use
Microphone’s
main unit
CAUTION: Be careful not to hurt your finger or nail
when you insert or remove the side support.
Removing the side support:
Remove the side support as
shown to the right.
Side supports
Earphone
Fit side
supports to
your head.
Microphone
2.5 mm (d)
Earphone
jack
Microphone
sensitivity
switch
(Default: HI)
OPC-2359
The crossed-out wheeled-bin
symbol on your product, literature,
or packaging reminds you that in
the European Union, all electrical
and electronic products, batteries, and
accumulators (rechargeable batteries) must
be taken to designated collection locations at
the end of their working life. Do not dispose
of these products as unsorted municipal
waste. Dispose of them according to the laws
in your area.
DISPOSAL
Image
About Microphone sensitivity
Select HI or LO sensitivity as necessary.
If you feel any discomfort with the standard
ear-piece, replace it with
the supplied thin type.
Make sure the ear-piece
is correctly attached.
ABOUT THE EAR-PIECE
(0.35”) (0.41”)
9 mm 10.5 mm
 こびはお買げいただ
て、にあす。
 は、 OPC-2359(
スイケール)にする
ン型ヘです。
 使用の前にの取扱説明書をお読
い。
取扱説明書
イヤホン型ヘッドセット
HS-102
使用上の注意
◎本製品は、防塵/防水構造はあません。
◎の上に重いもんだいで
い。
本製品を、強い衝撃を与えないださい。
故障の原因になるがあます
◎本製品を直射日光の当たる場所、温度変化の激い場
所に放置す、変形や変色があます
◎指定以外のケーブルに接続ないださい。
故障の原因になるがあます
◎赤ちんや小さなお子さの手が届かない場所で使用、保
い。
組み立ての手順
本製品をお使いには、別売品のOPC-2359(通話スチ内蔵型接続ケーブル)が必要です
OPC-2359へ
ヤホ
(付属品)
装着バ
マイ
マイ
替え
(初期設定HI)
イク感度ついて
「HI」感度が高「LO」す。
※マイクロ離、声の大きさ周囲の騒音ど、環
に応、切替えてい。
方で長さ
を調
q 装着バドの先端挿入口に込む
w 付属のヤホンを接続
装着バ回転さ
左耳で聞場合
右耳で聞場合
注意
着バドが易にれなな構造にいま
んだきは、指いため
注意
い。
(φ2.5mm)
ム株式会社、アイム、IcomInc.、アイコムは、株式会社の登録商標です。
はずすと
ら装
ドをなが
い。
装着バ
挿入口
付属のイヤースつい
◎本製品には細いタプのイヤーピーが付属ていす。
お好み合わせて交換使用ださい。
◎するきはれないよに奥実に取
付けださい。
約9 約10.5mm
※出荷時に装着されていま
装着メー
日本
ENGLISH
FRANÇAIS ESPAÑOL
A-7221X-1G-
q
a Printed in Japan
© 2015–2016 Icom Inc.
1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan
547ー0003

大阪市平野区加美南
1ー1ー32
Vielen Dank, dass Sie sich für dieses Icom
Produkt entschieden haben.
Das Headset HS-102 ist mit dem PTT-Kabel
OPC-2359 zu verwenden.
Bitte lesen Sie diese Anleitung sorgfältig vor
der Inbetriebnahme des HS-102.
ANLEITUNG
HEADSET
HS-102
Icom, Icom Inc. und das Icom-Logo sind registrierte
Marken der Icom Inc. (Japan) in Japan, den
Vereinigten Staaten, im Vereinigten Königreich, in
Deutschland, Frankreich, Spanien, Russland und/
oder in anderen Ländern.
Das Headset ist nicht wasserdicht oder
staubgeschützt.
NIEMALS schwere Gegenstände auf das Headset
stellen oder es einklemmen.
NIEMALS das Headset auf eine harte Oberfläche
fallen lassen, da es sonst beschädigt werden könnte.
SETZEN Sie das Headset nicht direktem Sonnenlicht
aus. Dies kann zu Verformungen oder Verfärbungen
des Headsets führen.
VERWENDEN Sie es nur mit dem angegebenen
Icom-Kabel. Ansonsten kann das Headset
beschädigt werden oder möglicherweise nicht korrekt
funktionieren.
BEWAHREN Sie das Headset außerhalb der
Reichweite von Kindern auf.
Das OPC-2359 wird benötigt (bitte separat
bestellen).
1) Setzen Sie die Seitenstützen in die
Haupteinheit des Mikrofons ein.
2) Schließen Sie den Kopfhörer an und drehen
Sie die Seitenstützen.
SICHERHEITSHINWEISE HEADSET MONTAGE
Seitenstützen
Verwendung
rechte Seite
Verwendung
linke Seite
Haupteinheit
des Mikrofons
ACHTUNG: Achten Sie darauf, Ihre Finger
oder Nägel beim Einlegen oder Entfernen der
Seitenstützen nicht zu verletzen.
Entfernen der Seitenstütze:
Entfernen Sie die seitliche
Unterstützung, wie rechts
gezeigt.
Seitenstützen
Ohrhörer
Passen Sie die
Seitenstützen an
Ihren Kopf an.
Mikrofon
2,5 mm (D)
Ohrhörer-
anschluss
Umschalttaste
für Mikrofon-
empfindlichkeit
(Standard: HI)
OPC-2359
Das Symbol einer durchgestrichenen
Abfalltonne auf Rädern auf dem
Produkt, den zugehörigen Unterlagen
oder der Verpackung weist darauf
hin, dass in den Ländern der EU
alle elektrischen und elektronischen Produkte,
Batterien und Akkumulatoren (aufladbare
Batterien) am Ende ihrer Lebensdauer bei einer
benannten Sammelstelle abgegeben werden
müssen. Entsorgen Sie diese Produkte nicht über
den unsortierten Hausmüll.
Entsorgen Sie sie entsprechend den bei Ihnen
geltenden Bestimmungen.
ENTSORGUNG
Bild
Über die Mikrofonempfindlichkeit
Wählen Sie nach Bedarf die die Empfindlichkeit HI
(Hoch) oder LO (Gering)
Wenn Ihnen der Standard-Ohrstöpsel
unangenehm ist, ersetzen
Sie ihn bitte durch den
mitgelieferten dünneren.
Stellen Sie sicher, dass der
Ohrstöpsel korrekt befestigt ist.
ÜBER DEN OHRSTÖPSEL
(0.35”) (0.41”)
9 mm 10.5 mm
Vi ringraziamo per aver scelto un prodotto Icom.
La cuffia microfono/auricolare HS-102 deve
essere utilizzata con il cavo con switch PTT
OPC-2359.
Vi preghiamo di leggere attentamente le
istruzioni per l’uso prima di utilizzare la cuffia
HS-102.
INSTRUZIONE
CUFFIA MICROFONO/AURICOLARE
HS-102
La cuffia microfono/auricolare non p2-ha alcun
indice di protezione da acqua o polvere.
NON MAI appoggiare oggetti pesanti sulle
cuffie e non schiacciarle in alcun modo.
NON far cadere le cuffie su superficie dure, in
quanto le cuffie potrebbero danneggiarsi.
NON esporre le cuffie alla luce solare diretta
in quanto potrebbero deformarsi o scolorirsi.
UTILIZZARE le cuffie solo con il cavo Icom
specifico; in caso contrario le cuffie potrebbero
danneggiarsi o non funzionare correttamente.
TENERE le cuffie al di fuori della portata dei
bambini.
E’ necessario il cavo OPC-2359, acquistabile
separatamente.
1)
Inserire il supporto laterale nell’unitá principale
del microfono.
2) Connettere l’auricolare e ruotare i supporti
laterali.
PRECAUZIONI MONTAGGIO CUFFIE
Supporti laterali
Utilizzo dal
lato destro
Unitá principale
del microfono
ATTENZIONE: Fate attenzione a non ferirvi il dito
o l’unghia quando inserite o rimuovere i supporto
laterale.
Rimozione del supporto
laterale:
Rimuovere il supporto laterale
come mostrato a lato.
Sppurti laterali
Auricolare
Adattare i
supporti alla
vostra testa.
Microfono
Jack
auricolare
2.5 mm (ø)
Switch sensibilitá
microfono
OPC-2359
Il simbolo del cassonetto barrato
riportato sul prodotto, sulle
pubblicazioni o sull’imballaggio
ricorda che nell’Unione Europea tutti
i prodotti elettrici ed elettronici, le
batterie e gli accumulatori (batterie ricaricabili)
devono essere portati in punti raccolta stabiliti
alla fine della durata in servizio. Non smaltire
questi prodotti come rifiuti urbani indifferenziati.
Smaltirli in base alle leggi vigenti nella propria
area.
SMALTIMENTO
Immagine
Sensibilitá del microfono
Selezionare HI (alta) o LO (bassa) a seconda della
necessità.
Qualora non troviate confortevole l’auricolare
standard, è possibile
sostituirlo con il modello più
sottile fornito in dotazione.
Assicuratevi che l’auricolare
sia allegato correttamente.
AURICOLARE
(0.35”) (0.41”)
9 mm 10.5 mm
Icom, Icom Inc. e il logo da Icom sono i marchi
registrati di Icom Incorporated (Japan) in Giappone,
Stati Uniti, Regno Unito, Germania, Francia, Spagna,
Russia, Australia, Nuova Zelanda, e/o altri paesi.
(Valore Imp.
di default: HI)
DEUTSCH ITALIANO
Utilizzo dal
lato sinistro


Produkt Specifikationer

Mærke: Icom
Kategori: Headset
Model: HS-102

Har du brug for hjælp?

Hvis du har brug for hjælp til Icom HS-102 stil et spørgsmål nedenfor, og andre brugere vil svare dig